Cisco WAN :: How To Setup 4500 CatOs
Oct 26, 2011
how to setup this old switch 4500. It is running CATOS and I want to make sure that when I connect it to the network it doesn't create a loop since it has to be compatible with other vendors, not just Cisco.I don't have anything connected but these are my concerns: It doesn't show my lacp-channel (i believe this is what is used to for Teaming network cards), it doesn't show my trunk ports.
TestSwitch> (enable) show lacp-channel
No ports channelling
TestSwitch> (enable) show trunk ?
detail Show detailed information
<mod> Module number
<mod/port> Module number and Port number(s)
[code]....
View 4 Replies
ADVERTISEMENT
Jul 28, 2012
My issue is that when trying to run the setup software for my new cisco 4500 router, an error message comes up which states that the new mac operating system 10.8 aka mountain lion is not supported. so now i had no choice but to leave my network unprotected as i cannot run setup. I was just wondering if there was another method by which i can configure the router without running the setup cd.
View 3 Replies
View Related
Oct 26, 2012
I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.
View 9 Replies
View Related
Jun 28, 2012
I want absolute max throughput possible to be achieved in all focal points. We're all in internet related industries. Between gaming and web-development latency and throughput are major factors for us.
1) Garage (office). downstairs
2) Each bedroom x4. upstairs
3) Living room. downstairs
The fastest line we can get is Comcast 50mbdown/5up (Wideband).
I am looking for the best way to achieve wireless and wired performance for our setup.
Our gaming computers may be in our bedroom, and we also may bring it down to the office every now and then for LAN sessions. Most wireless will be happening downstairs with our laptops, but since we may do LAN sessions then hard wired latency may be important there too.
I dont know if placing one D-link DGL 4500 on the top floor would be enough; which I currently own. url...As far as I'm aware wireless signals transfer best top down. Would this wireless router be enough on top floor and that's it?
View 12 Replies
View Related
Oct 23, 2011
i am unable to setup a Bluetooth connection between my nokia phone and my Dell inspiron N 4500. I am currently using windows 7 and the bluetooth icon in the Device manager window is unavailable.
View 5 Replies
View Related
May 1, 2011
I just started a new Position and they have CATos still runing on some of there 4506 and 6509 switches. I amy trying to come up with a plan to upgrade the switches to IOS but I dont know if they will take it or not. I know I need to get flash Cards to hold the IOS but i need to make sure that I get the right IOS for the Switches.
View 1 Replies
View Related
Jul 31, 2012
I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I need to pull the running config from the CatOS chassis and make it work on the IOS chassis. i can do this manually but was wondering if there are any trade secrets on doing this.
View 3 Replies
View Related
Nov 29, 2011
I have a 6506 with SUP1, no MSFC running CatOS.
Module 1: Removed
Module 2: WS-X6K-SUP1A-2GE
Module 3: WS-X6348
Module 4: WS-X6348
Module 5: WS-X6408A-GBIC
Module 6: WS-X6408A-GBIC
However, it doesn't seems to be able to bootup properly. Could this be an hardware issue? What should I do?
View 5 Replies
View Related
May 4, 2005
can i use vb scripts or bat files to execute cli commands on 6509 catos 7.6?any useful links or scripts?
View 2 Replies
View Related
Oct 24, 2012
I have a client who is changing their management IP scheme as a bridge to replacing equipment and much of the old equipment (Catalyst 4000) is running CatOS and I am a bit weak in CatOS. The existing Management IP is setup as follows:
set interface sc0 1 192.168.252.209/255.255.255.0 192.168.252.255
set ip route 0.0.0.0/0.0.0.0 192.168.252.1
What we want to change this to is as follows:
set interface sc0 110 192.168.197.209/255.255.255.0 192.168.197.255
set ip route 0.0.0.0/0.0.0.0 192.168.197.1
The devices are spreadout over a large area and visiting each device is almost out of the question due to a time deadline I was wondering if I run this set of commands will this allow me to keep a remote session (SSH) running until the change is complete?
set ip route 192.168.197.0/255.255.255.0 192.168.197.1
set interface sc0 110 192.168.197.209/255.255.255.0 192.168.197.255
set ip route 0.0.0.0/0.0.0.0 192.168.197.1
View 5 Replies
View Related
Feb 10, 2013
We are implementing NAC in our environment and unfortunately still some of our obsolete 6500 switches are running CATOS, the current (cat6000-sup2cvk9.8-6-4.bin) image does not support some of the commands related to NAC implementation. Therefore, I would like to urge you to provide me the 8.7 image which supports all the NAC related commands and will be easier to finish the long pending assignment.
We are in process of replacing the obselete hardware but that will take time.
So, 8.7 K9 CATOS image required.
View 4 Replies
View Related
Nov 7, 2012
I have to upgrade two Cisco Catalyst 6509E from Catos to IOS. I would want to know the requirements hardware or software for upgrading. Which are the recommended images I must download? From cat6000-sup32pfc3k9.8-4-5 to the latest stable version of IOS, is it recomended to pass to another previously version before?
I have viewed the following links,[URL]but, it doesn`t mention anything about that. The image below is the result of the "show version" command of one of our Cisco Catalyst.
WS-C6509-E Software, Version NmpSW: 8.4(5)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Aug 3 2005, 13:13:36
[code]....
View 2 Replies
View Related
Jul 23, 2011
If we have catos 6509 and MSFC and we need to connect new building with L3 I want to Do static route between two network i need to but ip in interface of switch should I but this ip on catos or MSFC,
Switch(config)# interface fastethernet 2/1
Switch(config-if)# ip address x.x.x.x x.x.x.x
In catos if want want do like above command what is the command .
View 6 Replies
View Related
May 27, 2013
I am trying to Disable Telnet and enable SSH in CatOS for 6500 .
View 12 Replies
View Related
Sep 26, 2012
I need to convert configuration from CatOS on 4006 to IOS on 4510. I am unable to find the conversion tool.
View 5 Replies
View Related
Nov 14, 2012
I am trying to find a command for dhcp snooping rate-limiting on a CatOS. The PFC card is PFC. PFC3B is said to support that command. But there seems no this command.
-6k> (enable) sh ver
WS-C6509-E Software, Version NmpSW: 8.4(5)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Aug 3 2005, 13:26:46
[Code] ......
Up time is 1183 days, 1 hour, 41 minutes
View 3 Replies
View Related
Oct 14, 2012
I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I would like to convert my CatOS running configs to IOS, and I know there used to be a tool for this.
I have searched around and found many broken links to an old Cisco tool to convert my former configs, is there any way to get this tool today? I have tried over 20 links and not been able to find a working one yet.
View 2 Replies
View Related
Apr 22, 2012
I have a question. I have a 6500 with two supervosrs and they both have CATOS. One of them failed and I need to replace. As long as the hardware is the same does the CATOS have to be indentical or can this be different.
View 4 Replies
View Related
Jul 17, 2012
how to convert configuration catos on 6500 to IOS image.
View 3 Replies
View Related
Nov 30, 2012
I need to replace a faulty fan unit on the catos WS-6509 switch. this Catos switch does not support show inventory so any other catos commands which will show me this part id?
View 2 Replies
View Related
May 15, 2013
I'm trying to configure an LACP channel trunk between a CatOS C6000 and a Dell PowerConnect.
I use mode active in both sides and it works great.
But, when I connect a Catalyst 3750X to the Dell PowerConnect the channel between C6000 and PWC shutdown:
2013 May 16 09:08:20 CEST +02:00 %SPANTREE-2-CHNMISCFG: STP loop - channel 5/19-20 is disabled in vlan/instance 20
2013 May 16 09:08:20 CEST +02:00 %SPANTREE-2-CHNMISCFG2: BPDU source mac addresses: 00-04-6d-43-a4-e2, 70-ca-9b-27-46-99
View 3 Replies
View Related
Oct 25, 2012
I am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
View 5 Replies
View Related
Jul 17, 2012
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
View 1 Replies
View Related
Feb 20, 2013
Have a new 4500-x (Comes with IPBase enabled), but I see only universal image is available for download (Which I understand has "all" features)...assume it is safe to use the latest universal image on 4500-x and the IPBase license will be automatically applied?
I also see there is a new rom upgrade available - Is this the correct procedure to follow: [URL]
Should I be doing the rom upgrade first?
View 1 Replies
View Related
Nov 8, 2011
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies
View Related
Sep 6, 2011
I have a 4510R+E switch that won't change to the SSO redundancy mode. After entering the 'mode SSO' command, the switch reboots the peer supervisor (as it says it will), but after it comes back up it remains in RPR mode. I've tried rebooting the peer supervisor manually, rebooting the entire chassis, manually power cycling the entire chassis, and reseating the sups, but the switch remains in RPR mode. The issue started when I swapped the switch's supervisor with the supervisor of another 4500. The same issue was observed on the other 4500 as well, but after several reboots, I got it to change to SSO mode. Prior to the swap, both switches were running in SSO mode just fine.Since we're running IOS version 15.0 with the 'spare sup' license, I suspect the issue arose because of licensing complications (with relation to the chassis serial number and the like) when I swapped the sups....although this doesn't explain why the other switch changed to SSO after some troubleshooting.
View 1 Replies
View Related
Oct 27, 2012
I do terminal monitor on my 4500 switch.I can't see the status of the interface ( when it become up or down)What is the problem? I need to add a command?
View 3 Replies
View Related
Dec 12, 2011
Im trying to locate the PDLM for the RTP audio for the 4500 series switch,
System image file is "boot flash:cat4500-entservices-mz.150-2.SG.bin"
Cisco WS-C4507R+E (MPC8245) processor (revision 7) with 524288K bytes of memory.
MPC8245 CPU at 333Mhz, Supervisor IV
Last reset from Power Up
8 Virtual Ethernet interfaces
48 Fast Ethernet interfaces
100 Gigabit Ethernet interfaces
403K bytes of non-volatile configuration memory.
It seems to be an easy task for routers:
[URL]
But not for these 4500's
[URL]
View 1 Replies
View Related
Jun 8, 2011
we got 2 Cisco 4005 Switches with IOS 12.x. t.Now we have two new Cisco 4500 Switches with Supervisor 6E-L.But i dont really understand the new syntax / configuration method of ios 15.
View 2 Replies
View Related
Jan 1, 2012
I've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies
View Related
Jul 28, 2012
Im wanting to add an additional module in to my Cisco 4500. Is as simple as plug and play or is there some commands that I need to add or anything I should be aware of.
View 2 Replies
View Related
Dec 1, 2011
We inherited a lot of the equipment from another team of network administrators and every now and then, we run into a switch with some old code or configuration that was left behind and missed by us. Today, I discovered that CPP was enabled on 3 of our access-layer switches in one of the buildings we support.
View 3 Replies
View Related
Jan 17, 2013
We have a Cisco 4500 core switch and 2 Motorola AP 6532 access points. From the Motorola side the goal is to allow my corporate users access to network resources meanwhile offering my guest users only internet connectivity. My thought is to create two separate VLAN’s on my Cisco switch ex: vlan 10 (Business) 192.168.50.x and create another vlan 20 (guest) 192.168.2.x, also I made the proper configuration changes inside my Motorola AP device as well. From the Motorola I can ping myself but not my switch?
View 2 Replies
View Related