Cisco :: 4500 - Setting Up VLAN With Motorola AP?
Jan 17, 2013
We have a Cisco 4500 core switch and 2 Motorola AP 6532 access points. From the Motorola side the goal is to allow my corporate users access to network resources meanwhile offering my guest users only internet connectivity. My thought is to create two separate VLAN’s on my Cisco switch ex: vlan 10 (Business) 192.168.50.x and create another vlan 20 (guest) 192.168.2.x, also I made the proper configuration changes inside my Motorola AP device as well. From the Motorola I can ping myself but not my switch?
View 2 Replies
ADVERTISEMENT
Feb 21, 2012
Trying to set up the Cisco VPN router for remote acces to our network.We have ATT Uverse DSL and it is a Motorola Router, i think NGT 510.the Uverse router has very limited setup options.I cannot set it up as a bridge.The only thing I can figure out is to set the ip passthrough option to the VPN router.We have a static ip address for our internet service.
I have tried several setup and connection options, but cannot get it to work.
1. How to physically connect the routers and network devices?
2. How to setup both routers to play nice.
View 1 Replies
View Related
Jan 12, 2012
I have a network that is currently set up in the following way:Modem -> vonage Motorola router -> wireless router Most computers are hard wired to the Motorola router. Some other ones connect via the linkseys wireless router. All computers are able to connect to the Internet. The problem I have is that I will be setting up a home computer as a file server connected to the Motorola router. The network acts as though it is two meaning that computers on one router can't see computers on the other router. What steps should I take in order to make all computers accessible through both routers.When I type 192.168.1.1 from a computer on the Motorola router, I get nothing, when I type in my actual ip address, I get the Motorola router. When I type in 192.168.1.1 from a linkseys connected computer, I get access to the linkseys router.
View 3 Replies
View Related
Dec 10, 2012
read the posts regarding vlans that are administratively down, they suggested that they are down if no ports are assigned to them, however I do have a switchport assigned, and the interface is still down. This is on the vtp server and on the clients. The vlan is not listed when issuing show vlan brief. Other vlans configured in a similar way do show and their interfaces are up. These are two Catalyst 4948-10G.Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).
View 5 Replies
View Related
Jan 24, 2012
I have an in production x2 4500's which I would like to add a new vlan and IP address to.
Sample config...
interface Vlan65
ip address 10.100.6.2 255.255.255.248
no ip redirects
no ip unreachables
no ip proxy-arp
standby 65 ip 10.100.6.1
standby 65 timers 1 3
standby 65 preempt delay minimum 120
View 5 Replies
View Related
May 20, 2013
We have observed WS-C4507R-E got rebooted while creating the L3 VLAN ( while No shut).Is there any known bug for below IOS ?cat4500-entservicesk9-mz.122-40.SG.bin,
View 4 Replies
View Related
Nov 24, 2011
I got some problem with enabling dhcp snooping on 4500 (cat4500e-lanbasek9-mz.122-54.SG.bin) the topology is as below: dhcp snooping enabled only on CORE (with interface trusted to dhcp server)the problem is that I put these 2 commands
ip dhcp snooping
ip dhcp snooping vlan 1
but it is not enabled on any vlan
SW-CORE#sh ip dhcp snooping
Switch DHCP snooping is enabled
DHCP snooping is configured on following VLANs:
none
DHCP snooping is operational on following VLANs:
[Code]...
On B1 if I turn it on there is a "1" in the section " DHCP snooping is configured on following VLANs:" but on core no.As you can see I did put the trusted on the interface in the direction to the dhcp.First I thought it can be a problem with option 82, I've read a lot about the issues with that, but the problem would be explicable if the client did receive IP address, but it does.
View 3 Replies
View Related
Feb 3, 2011
I purchased a RV082 router because it said it would support VLANs, but I cant seem to get it set up how I want.
I would like the first internet port on the router to feed one VLAN with an IP address. I would like the second internet port (DMZ / Internet) to feed a second VLAN with a different IP address. These two VLANs should be completely separate. I can see how to set up VLANs but I can seem to find how to separate the feeds and assign them different IP addresses.
Can I set up the RV082 to do this?
View 1 Replies
View Related
Nov 27, 2011
I am primarely enquiring whether the setup I have explained below is actually possible, and if so then how I can set this up. I know it isn't the easiest configuration and I need to set this up without purchasing any more equipment if at all possible.I have a Cisco SG 300-28 setup with three VLAN's. [code] Default Gateway is 192.168.10.1 (Netgear Router)I have a Wireless network setup (Netgear WMS and 2 WAP's) configured with the TWO VLAN's (1 and 3). These go into ports on the Cisco SG 300-28 which are tagged on both VLAN's. The Business wireless worked fine but the guest network didn't reout out to the internet.After some troubleshooting I realised the reason the guest wasn't working was because there was no route back from the internet to the router.
The router I have isn't really ideal, it is a Netgear DGN2200, but I managed to create a static route to 192.168.30.1 with a metric of 2, with 192,168,10.254 being the hop. Success, the connection worked, the only problem is that now my guest network can see my business network because the business network is using the static route on my router to route back over to the guest network (due to the limitations of this device I can't do anything about that)Guest network can connect to Business VLAN via switch. I am assuming this is because the router is on the Business VLAN and the default gateway is the router. As they are on the same network the Guest network can inevetably see the business server and network.The Business network can get back to the Guest network via the router using my static route I created. The static route is really basic and I can't create a firewall rule on the router to prevent the Business network speaking to guest network because it only has a LAN - WAN firewall and this connection is LAN - LAN.
What I need is...to somehow stop any traffic from the 192.168.30.0 network routing to anything on the 192.168.10.0 network, appart from the router on 192.168.10.1.Is this possible? I have this setup on a number of different site, the only difference is I have a CIsco Security Router on these with the VLAN's configured so I don't have this problem. Because I have a rather limited Netgear DGN2200 I am unable to setup the VLAN's correctly and as such I need to see if I can do this on the switch in any way.
View 2 Replies
View Related
Mar 24, 2011
I got the SG 300-20 small business L2/L3 switch. I've read through the 325 page pdf manual and I still can't figure out how to do what I need to do. Here is my setup using example ips.[code]
I want to be able to have any workstation I put on the workstations vlan to use 69.30.44.2.34 as a gw and from there route to 170.4.5.5 and from there to the outside. Basiclly, I want to be able to route ips from two different subnets on two different vlans. I've read through the docs and so far I have vlan1 setup and vlan 2 setup fine but I have no clue how to get the routing to cross vlans. The docs say the only way to have vlans talk to each other is by routing through the vlans ip interfaces but I have no clue how. There isn't a simple step 1,2,3 chapter that gets you to route between two vlans. What am I doing wrong? I put in some IP route entries but nothing seems to work.
View 3 Replies
View Related
Oct 3, 2012
I'm new at this stuff and very stumped. I have one WAP with multiple SSIDs that support VLAN ID (for a private and guest wireless network) and a managed switch that supports tag or port based VLAN ID. How do I set up the switch so that the networks are separate, but can still reach their own routers to get on the Internet? In case details are necessary, the WAP is a Cisco Aironet 1130AG and the switch is a Netgear FS750T2
View 14 Replies
View Related
Aug 26, 2012
I have to admit I've never written my own Cisco configuration and I probably know just enough to break things. The last time I configured a Cisco was a few years ago, and the Wachovia people just told me what to type.
I have a Cisco WS-C3548-XL-EN and a Cisco WS-C3524-PWR-XL-EN "Inline Power" with default configurations and I want to setup VLANs. Basically, would this work?
SWITCH 1:Router on port 39, Wifi on Port 47, Uplink to 2nd switch's port 24 on port 48
Code:
en
conf t
interface VLAN10
no ip directed-broadcast
no ip route-cache
[code]....
And then I would test that it works, if it does issue #write memory, and it it doesn't powercycle and try again?
View 9 Replies
View Related
Apr 15, 2013
I have been though the setup a couple of time with no luck pinging one pc to another from vlan 10 to vlan 20. I posted the running configs and some other information from my router and switch. I am relatively new to all of this so if you need me to post more information from the hardware let me know and Ill put it up. There are no firewalls in place and I know the cables are good because I switched them around to make sure. Also when I change the ip on my second machine for vlan 10 I can ping from one pc to the other but when I try the same for vlan 20 I get nothing.
**From my 2950 switch**
Current configuration : 2825 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
[code]...
View 5 Replies
View Related
Apr 26, 2011
I have a siemens gigaset567 unit.I suspect others are accessing via vlan.
View 1 Replies
View Related
Feb 23, 2012
I am trying to set up a VLAN on my Netgear switch (GS105E). I want to create two separate networks and I want both of them have internet access.
I have configured port 1 and port 5 as vlan1 and port 2 to port 4 as vlan2. I plugged a cable from the router to port 5, and the computer on port 1 has internet access. However, the computers on port 2 to port 4 have no internet access.I had tried to create VLANs with the router but had no luck.
View 3 Replies
View Related
Jan 25, 2012
I need to create several VLans on my switch.After reading the admin guide pdf, i still don't understand how to create any simple VLan.some tutorial or steps (with IE or Mozilla browser) how to create and use VLan, and to connect one VLan to another.For example,i need to create 3 VLans.
First Vlan consist of 5 ports (Vlan Name = Red)
Second Vlan consist of 15 ports (Vlan Name = Green)
Last Vlan consist of the rest of the ports (VLan Name = White)
View 7 Replies
View Related
Mar 6, 2012
Is there any way to granularly allow hosts from one vlan to be able to access another vlan with Inter-VLAN routing DISABLED?Can the use of an ACL override the setting?In general I don't want any traffic between VLAN's but there are 2 hosts on one VLAN that I would want to allow access to a server on another VLAN.
View 1 Replies
View Related
Oct 2, 2011
I have recently purchased 2 SG 300 switches, 1 x SG 300 52 & 1 x SG 300 10, and I am hoping getting the following set-up working.To assist I have drawn the following simple network diagram (below) which hopefully makes it a little clearer what I am trying to do:I have 2 companies occupying a single office with the requirement to share printers/devices etc... so basically I am looking to set-up 2 VLANS (say VLAN 10 & VLAN 20) with inter-vlan routing. To add a little complexity the main comms area is located in the basement of the building, this houses the 2 DSL routers and 2 Servers, one for each company. I am proposing putting the SG 300 10 port switch in here and then use the 3 uplinks I have been given to connect back to the SG 300 52 which is in a patch cabinent 2 floors up. I want to use 2 uplinks (in a LAG) for Company A and 1 uplink for Company B. FYI. DHCP is being served out by each respective router.
View 6 Replies
View Related
Mar 22, 2011
I am migrating an a group of workstations that run a fire system from one software to another. The current workstations run the following info:123.123.123.xxx 255.255.255.0The new workstations run:100.100.100.xxx 255.255.255.0There is a central switch location using a GE-DSG-244 Layer 2+ Managed switch. There are two remote location using GE-DS-82 Managed Switches.The two networks must remain isolated, yet use the same fiber communications. The central switch connects to the two location using MM Fiber. From my research I believe I need to use the 802.1q standard to allow port trunking between the two switches.
View 7 Replies
View Related
Apr 15, 2013
I am trying to set up a network that has 1 internet connection, requires a local LAN for the business, and another LAN for public wireless access. Here is what I have and details on what we want to do.
1- Cisco ISA570 Router no WIFI
1- SG500-52P switch
6 - WAP321 Access Points
We have the main LAN set up and all is working well, internet access, 6 WAP's connecting and all is working like a charm. Internal IP range is 192. 168. 0.0/24.We have all 6 WAPs on the internal network, with 2 SSID's on each WAP and each SSID is assigned to a VLAN. One SSID is internal for staff, the other is for guest access for members. The internal staff wireless access is working fine.
We want the guests to be able to access the internet, but not the internal network, but we need to access them for administration from the internal network.
We created a second VLAN on the switch and added the 6 WAP ports to it as tagged for VLAN2. These 6 ports are also on VLAN1 (default). We have a second VLAN on the router, have it handing out DHCP addresses for the 192.168.25.0/24 range with DNS servers.
Where we are having trouble is with getting the guests wireless access to work. Guests can see the wireless, log onto the access point but that's it. They don't appear to get a 192.168.25.0/24 IP, or any IP actually, and thus cannot do anything.
View 5 Replies
View Related
Mar 6, 2012
We are trying to setup a WAP4410N with 2 SSID's. One SSID for our private network and the other for guest internet access. On the VLAN and QoS page there is a setting for priority. What would be the suggested values for this setting? We obviously want our private network to receive priority over our guest network.Also, does VLAN Tag setting need to be on Tagged to determine private from guest traffic?
View 2 Replies
View Related
Apr 17, 2013
One of the ports on the 3750 stack was configured for VLAN121. It was changed to VLAN40 and the configuration saved. Both VLANs exist in the switch configuration. As soon as a host was connected (in this case, a label printer) the port VLAN reverted back to VLAN121.
View 3 Replies
View Related
Feb 26, 2013
We got a layer3 switched network, with one vlan for every switch, routed by a cat4006. [code] So can we put some ports on different switches in, let`s say vlan 50, with different ips? For example, Port 0/3 on Switch 1 and 0/8 on Switch 2, but keeping the ip of the "old" vlan? Or is it necessary to configure a specified vlan interface with ip-adress for every vlan if i want to route it?
View 4 Replies
View Related
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Jan 12, 2013
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies
View Related
Jan 10, 2012
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Aug 12, 2012
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
View 1 Replies
View Related
Feb 2, 2011
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies
View Related
Mar 31, 2013
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
View 4 Replies
View Related
Jan 23, 2011
where is the WEP located on my att Motorola router?
View 1 Replies
View Related
Sep 16, 2012
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies
View Related
Oct 12, 2011
I'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
EZVPN_Remote(config-if)#int fa1
EZVPN_Remote(config-if)#dot
EZVPN_Remote(config-if)#dot1?
dot1q
EZVPN_Remote(config-if)#dot1
[code]....
View 1 Replies
View Related
