Cisco LAN :: 2950 / Can't Ping From One Vlan To Another After Setting Up Trunk
Apr 15, 2013
I have been though the setup a couple of time with no luck pinging one pc to another from vlan 10 to vlan 20. I posted the running configs and some other information from my router and switch. I am relatively new to all of this so if you need me to post more information from the hardware let me know and Ill put it up. There are no firewalls in place and I know the cables are good because I switched them around to make sure. Also when I change the ip on my second machine for vlan 10 I can ping from one pc to the other but when I try the same for vlan 20 I get nothing.
**From my 2950 switch**
Current configuration : 2825 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
[code]...
View 5 Replies
ADVERTISEMENT
Mar 7, 2012
I am looking into the possibility of using private vlan's for some dmz implementations however I do have what may be some very rudimentary questions. It seems straightforward how to configure the primary/secondary vlan configuration as well as associating them. However in my case I would be looking to configure the PVLAN on a 6500-vss platform acting as the router while all of the hosts which I would desire to have in the isolated vlan would be spread out across a number of older Cisco switches which only support "protected port" setup or Procurve switches all of which I do not have budget to replace with something newer. So in my scenario I would have a 6500 connected by trunk to multiple switches which only support a protected port setup such as a Procurve (top of rack) or a Cisco 2950. As the Procurve or 2950 would not support Private VLAN setup, do I then just configure the secondary vlan to be allowed across the trunk from the 6500, configure that vlan on the Procurve or 2950 (as vtp will not foward the info for the secondary vlan) and assign that vlan to the host port as well as setting it as a protected port and this will communicate just fine across the trunk to the router as well as stopping the protected port in top of rack switch 1 from being able to communicate to a protected port in top of rack 2,3,etc? If the above scenario is what needs to be done, do I just use a regular trunk or do I have to use a PVLAN trunk?
View 2 Replies
View Related
Oct 6, 2011
Telco provided a BGP connection on MPLS network. When I connect router directly to Telco switch I can see BGP neighbor, so my router BGP config is OK. However, I need to put this router in a diffferent building and want to bring the connection over on a "trunk"; now I loose the BGP neighbor. I'm sure I did this before and it worked OK. I'm trunking between 2 x2950 switches using this config on each switch. [code]
I also configured the trunk as vlan 1214, which is the encapsulation provided by the Telco (dot1Q 1214).
View 6 Replies
View Related
Apr 15, 2010
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
View 16 Replies
View Related
Mar 15, 2013
in the last days i'm encountering some issue about ping on some 2950 access layer.These ones are directly connect (fiber trunk) to 4500 core switches. Ping response is very high between 200 up to 600 ms for a period about 30-40 seconds, then returns to normal valueI tried to ping every host connected to this 2950 and ping responses are normal 1ms or less.
View 7 Replies
View Related
Feb 16, 2011
i would like to setup a L2 VLAN trunk connection over a VPN. I hear this can be done with a GRE tunnel. I currently have Cisco MWR2941's that i would like to configure the TRUNKs on then push them over a 5520 VPN ( IPSEC Tunnel ) to a 5510. on the other side of the 5510 i will have another MWR2941 to recieve the trunk.
how to configure this trunk or some configuration ideas?
View 3 Replies
View Related
Jun 29, 2012
I'm trying to obtain the vlans on a trunk and also whether the port is a trunk. Ive seen VTP mib, but these dont appear present on my switch (2950).
View 4 Replies
View Related
Feb 11, 2012
I've connected a dslmodem/router to a fast ethernet port(fa0/1) on a 2620 router.There is a 2950 switch connected to the other port (fa0/0).I can ping the Internet via the router but and the switch but not from a host connected to the switch.I can't reach the dslmodem from the host pc.I've configured nat(overload) on the router.
View 8 Replies
View Related
Sep 2, 2012
ASA 5505, I got a security plus license which allows multiple VLANs.I want to be able to configure the ASA to allow only RDP session (One way) to another Switch where all the VLANs are. I've attached a pic of what I want but I'm struggling.
I looked at documentation saying you should have inside and outside interface but I'm not sure on this scenario.I've configured inside interface on ASA e0/1 and interface VLANs but not sure what to do between ASA and Switch?
View 2 Replies
View Related
Feb 11, 2013
I have 2 hosts, 1 plugged in fa 0/21 in VLAN 101 and another in fa 0/22 in VLAN 101 on our L2 Cisco 2960. If I try and transfer files from either host the gig 0/1 trunk port on the 2960 leading tot he 3750 fa 0/1 port hits 100mb (using a real time bandwidth monitor tool), but why? This VLAN is on the same switch, why does it go one way up the trunk to the L3 3750 switch? The L3 3750 is the VTP server and the 2960 is a client. I would of thought the traffic stays local. The 2 hosts don't even have a gateway set.To sum up the typology the 2960 and 3750 are trunked using a single cable. The 3750 hangs of a ASA firewall using SVIs.Here is whatthe traffic looks like when copying a file between hosts (2gb file).
3750 L3 Switch (VTP Server)
interface FastEthernet1/0/4
description Trunk to Cisco 2960 Gig 0/1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
[code]....
View 6 Replies
View Related
Sep 22, 2012
I need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies
View Related
Nov 13, 2012
I have got 2 Cisco switches (3560G and a 3560X) connected by a trunk port. see config below:
3560G#sh run int gi0/26
Building configuration...
Current configuration : 130 bytes
[Code].....
I can't seem to get VLAN 79 through to the first switch (3560G). Beyond this switch there is a router with acts as default-gateway for the respective VLANs. For VLAN 79 it is 192.168.79.1. I can ping this from the first switch but can't ping it from the second (3560X) switch but can ping 192.168.25.1 which also is the default gateway for this switch.
View 7 Replies
View Related
Jan 27, 2013
We bough an Cisco 2911 router, and as i see the "ip sla monitor" command is not supported. Which license/IOS upgrade should i buy the fullfill this. And i cant add a trunkport to the iunterface even cant add a vlan to interface. How do i a trunkport on the cisco 2911 router. ANd how can i do a vlan on a interface on the router.
View 2 Replies
View Related
Dec 12, 2010
I have two VLANs set up on a Catalyst 2950 switch: VLAN 1 (192.168.1.x) and VLAN 2 (192.168.2.x). VLAN 2 can ping the router on the 192.168.1.x network and nothing else, which is what I want. However, computers on the 192.168.1.x network can ping computers on VLAN 2, which is what I do not want. I want to make it where VLAN 1 and VLAN 2 cannot communicate with one another, but that VLAN 2 can still ping the router on VLAN 1. I've read about access control lists and ip tables
View 3 Replies
View Related
Oct 1, 2012
My customer has various Cisco switches but only cisco 2950 switches has the problem of ping timeout or reply time is too long(average more than 2 sec). It will cause I Network Mangement software alarm always.
View 4 Replies
View Related
Dec 25, 2012
I have trunk etherchannel ports 47,48 which both have Vlans allowed on trunk 70,71. Everything works pretty fine. Now I am trying to add a new VLAN 72 to these ports.
conf t
interface FastEthernet0/47
switchport trunk allowed vlan add 72
exit
exit
So far so good. But when making the same command for port FastEthernet0/48 my switch stuck.
View 8 Replies
View Related
Dec 6, 2012
can i have 4 links from an ESX server to 6500 , each link represents a trunk link carries each the same 2 VLAN , 100 and 101 , keep port-channel out of the picture , does it work well?
View 12 Replies
View Related
Jul 5, 2012
I have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihomed (Broadcom) on the other side an it is supposed to be on this vlan with one of it's network interfaces. We had a pwer outage and now it cannot communicate on this vlan. However, everything else on the vlan can reach all the other nodes accept this server in the front of my building. All the devices in the same room are linked to the same switch which has one port (fa0/17) on vlan0010 and can ping eachother just fine. The server is hooked to port 24 on my server room switch and Gigabit port one goes to a fiber converter all the way to the back. It then gets converted from fiber to cat5e again and links into the switch (2960) in the backroom.
View 5 Replies
View Related
Jan 25, 2012
Need to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
View 1 Replies
View Related
Nov 15, 2011
a number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies
View Related
Nov 8, 2011
Currently we have a 6513 core (running IOS and doing limited routing) with VLAN Trunking to about a dozen 3560 edge switches, with various VLANs going to each of the edge switches. All works well. We are downsizing and replacing the 6513 core with a 3750G stack. We have the stack up and running in the lab, and want to slowly (as we move floors) migrate all of the edge switching to the 3750 stack.
The plan is to connect the 3750 stack to the 6513, then slowly migrate the edge switches to the stack (from the 6513). I would like to put in place 4 x 1GB trunk links between the 6513 and the 3750 stack before I start moving edge switches to ensure adequate bandwidth. Once all of the edge switches are on the new 3750 stack, I will start to decommission the 6513.
What is the best way to configure the links between the cores (old 6513 and new 3750 stack)? I can easily get the edge switches configured to the 3750, but am worried about the core links. I really want to avoid having to perform an all-at-once cutover of the cores. Another question is when do I try and migrate the VTP server role from the 6513 to the 3750 stack? I could simply make everything transparent, and ditch server-based VTP, as we rarely change or creat VLANs.
View 3 Replies
View Related
Apr 16, 2002
I have a switched network of C2980 & C3548 switches with multiple VLANs. I would like to understand the difference between Multi- VLAN ports and trunk ports. What circumstances would dictate using one over the other? If I configure the router port as Multi- VLAN, does the router still require sub-interfaces?
View 9 Replies
View Related
Apr 27, 2012
Stumped again with my Catalyst 2950. Everything is working perfectly with wan/dhcp/router on fa 0/1 with all ports assigned to vlan1. All devices plugged in connect to the router correctly with ip's being assigned via dhcp.Instead of hooking up by console port I want to be able to SSH or telnet in to the switch using any port while still maintaining the above functionallity. Is it possible to assign a dhcp assigned ip address to vlan 2 and have vlan1 and 2 bridged? Or is there a better way of doing this ?
View 3 Replies
View Related
Jul 4, 2012
spam up the boards with the same basic CCNA level stuff, but I have a couple of questions about ios differences, limitations, and references. I have the following three switches. One appears to be considerably dated in regard to software version. My confusion/ignorance stems from managing VTP settings.
2924XL 12.0 5 WC8
2950 12.1 22 EA6
2950 12.1 22 EA6
When I set either 2950 switch as the VTP server, and the other as a client, the client inherits the server settings as expected. However the 2924 requires that I go into the vlan database from priv exec and manually set vtp client. That's pretty similar to setting any switch to client mode. The problem I am observing is that after setting the 2924 to client, it still doesn't inherit vtp version settings or pruning settings. I still have to manually configure those. Additionally, if I copy run start the 2924 after making these manual settings, and then reload the switch, all the settings are lost and it defaults back to server mode with all features disabled. From my searches, it looks like vlan information is stored in vlan.dat, but all the documentation I've found is on 12.1 ios which doesn't appear to use vlan database for vtp setup, meaning it might still be an issue, but not one I'm focused on at the moment.
Is the vlan database dumped at reload? I've read vlan.dat is stored in nvram and should be saved after a copy run start, but that is not the case for me.I have since set the 2924 as the server, manually configured the server from vlan database, executed copy run start, and reloaded the switch. Oddly, my manual settings saved from the reload, meaning I only lose settings when the switch is in client mode.Am I missing additional necessary client commands to save the config, or is this just a limitation of either the 2924XL or the 12.0 ios?On a related but completed out of scope topic, without a cisco service contract, how am I supposed to make heads or tails of all the different versions of ios, along with the letter-based features and what-not? I can't even find my 2924 in the list of platforms when searching for ios upgrades.
View 5 Replies
View Related
Dec 11, 2011
We have a group of computers on their own VLAN. A router allows internet access while keeping them sandboxed. We don't want them accidentally connect to our production network. We blocked their wireless MACs in unauthorized WAPs. I'd like to do the same thing for their ethernet MACs on our switches, (a mixture of 2950,2960 and 2960G currently testing on C2960-LANBASE-M, Version 12.2(25)SEE2). I've been unable to locate the correct method on google, by searching these boards or in the command reference.
What is the best practice for blocking a group of MACs from accessing a particular VLAN on a network consisting of several Layer 2 Switches?
View 4 Replies
View Related
Jun 6, 2012
I have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
View 5 Replies
View Related
Jan 20, 2012
I need adding a vlan to the trunks bundled in port channel. I know how to add v lans to a port channel with Cisco IOS but with CAT OS.
I have 2 ports bundled to form ether channel in switch which is running CAT OS. There are already few v lans allowed in the trunk of each interface. now I need to add one more v lan.
For Example:-
v lan 135 needs to be added in addition to the existing v lans.
clear trunk1/2 1-112,115,117-134,136-4094
set trunk 1/2 on dot1q 113-114,116,135
and similarly on the 2nd interface
so if I add vlan135 to the trunk one after another will it cause any service disruption?
View 3 Replies
View Related
Nov 13, 2012
I have a 3750 as a core and have a series of HP Procurve switches that are daisy chained using one port. I have two vlans on the port now (6 &9) and everything works fine, all switches communicate and end devices on the switches are also talking. There is a requirement to add a device towards the end of the chain which requires it to connect using Vlan1. Once I add Vlan1 to the port onthe 3750 I lose connectivity to all the HP switches.
View 4 Replies
View Related
Sep 24, 2012
Current Situation:We are able to reach server IP -10.203.206.40 from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.
Requirements
==========
1) Now we would like to add one more L3 interface between 4506 & 4948 for redundancy purpose.
2) Make available Vlan 540 in 4948 from 4506... need to create two trunk links between 4506 & 4948 and allow vlan 540.
View 14 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
Nov 9, 2011
i am facing a strange issue on cisco 2950 .IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA9, RELEASE SOFTWARE (fc1) suddenly my phone stopped working for DTMF tone, i mean when i dial a conference bridge lets say 6565 and then it ask for conference bridge code lets say 12345, it doesnt recognize the code and says code is invalid, SIP Proxy is Asterisk in this case.Currently my cisco switch port is configured for dual data + voice vlan, where DTMF dont work, sample config below [code]
View 2 Replies
View Related
Apr 8, 2012
Randomly when I try to access to 2950 from management tools, switch is unreachable, I have to access from other switch and reload 2950.
Problem only is from managemt tool to managament vlan 1 2950.
The strange thing is that management interface is encountering a very fast increase of throttles, broadcast and ignored packets:
2950#show interfaces vlan 1
Vlan1 is up, line protocol is up
Hardware is CPU Interface, address is 0023.3488.fd65 (bia 0023.3488.fd65)
Internet address is xxxxxxxxxx
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
It could be a hardware problem?, IOS has been upgraded.
View 11 Replies
View Related
Jan 2, 2012
I need to implement the shaping VLAN only on the trunk link between the 6500 and 3560. [code]
View 8 Replies
View Related
