Cisco Switching/Routing :: 2950 To Assign DHCP With VLAN
Apr 27, 2012
Stumped again with my Catalyst 2950. Everything is working perfectly with wan/dhcp/router on fa 0/1 with all ports assigned to vlan1. All devices plugged in connect to the router correctly with ip's being assigned via dhcp.Instead of hooking up by console port I want to be able to SSH or telnet in to the switch using any port while still maintaining the above functionallity. Is it possible to assign a dhcp assigned ip address to vlan 2 and have vlan1 and 2 bridged? Or is there a better way of doing this ?
Have a client wanting to hand out public ip addresses to all clients from a PFSense Firewall terminating the internet connection.
How do I allow the Cisco Switches currently in place, configured with private ip addresses in the 10.10.x.x ranges and Vlans, where the main 3550 layer 3 has defined dhcp scopes for each vlan, to relay dhcp requests from all vlans to the PFSense firewall?
I assume I would take off the currently defined dhcp scopes for the vlans and configure each vlan/switch with the ip helper address and specify the PFSense firewall and that Nat would have to be disabled onthe firewall?
spam up the boards with the same basic CCNA level stuff, but I have a couple of questions about ios differences, limitations, and references. I have the following three switches. One appears to be considerably dated in regard to software version. My confusion/ignorance stems from managing VTP settings.
When I set either 2950 switch as the VTP server, and the other as a client, the client inherits the server settings as expected. However the 2924 requires that I go into the vlan database from priv exec and manually set vtp client. That's pretty similar to setting any switch to client mode. The problem I am observing is that after setting the 2924 to client, it still doesn't inherit vtp version settings or pruning settings. I still have to manually configure those. Additionally, if I copy run start the 2924 after making these manual settings, and then reload the switch, all the settings are lost and it defaults back to server mode with all features disabled. From my searches, it looks like vlan information is stored in vlan.dat, but all the documentation I've found is on 12.1 ios which doesn't appear to use vlan database for vtp setup, meaning it might still be an issue, but not one I'm focused on at the moment.
Is the vlan database dumped at reload? I've read vlan.dat is stored in nvram and should be saved after a copy run start, but that is not the case for me.I have since set the 2924 as the server, manually configured the server from vlan database, executed copy run start, and reloaded the switch. Oddly, my manual settings saved from the reload, meaning I only lose settings when the switch is in client mode.Am I missing additional necessary client commands to save the config, or is this just a limitation of either the 2924XL or the 12.0 ios?On a related but completed out of scope topic, without a cisco service contract, how am I supposed to make heads or tails of all the different versions of ios, along with the letter-based features and what-not? I can't even find my 2924 in the list of platforms when searching for ios upgrades.
We have a group of computers on their own VLAN. A router allows internet access while keeping them sandboxed. We don't want them accidentally connect to our production network. We blocked their wireless MACs in unauthorized WAPs. I'd like to do the same thing for their ethernet MACs on our switches, (a mixture of 2950,2960 and 2960G currently testing on C2960-LANBASE-M, Version 12.2(25)SEE2). I've been unable to locate the correct method on google, by searching these boards or in the command reference.
What is the best practice for blocking a group of MACs from accessing a particular VLAN on a network consisting of several Layer 2 Switches?
Actually i have 7600 router and all trafic passes through Gi0/1(Routed port) interface to 6500 series switch. I need to create a vlan on this router eg. vlan 10 Any how it is possible assign a vlan to routed port and traffic of wan interfaces and the vlan traffic passed together.
I am wondering if it has its own DHCP router and if theres a command to enable it?Also Random side question. it hands out ip addresses to other devices (the 2950 im using infront of a router) but when I hook up another switch to this switch it doesnt initialize the port or try to connect? why.
i am facing a strange issue on cisco 2950 .IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA9, RELEASE SOFTWARE (fc1) suddenly my phone stopped working for DTMF tone, i mean when i dial a conference bridge lets say 6565 and then it ask for conference bridge code lets say 12345, it doesnt recognize the code and says code is invalid, SIP Proxy is Asterisk in this case.Currently my cisco switch port is configured for dual data + voice vlan, where DTMF dont work, sample config below [code]
Randomly when I try to access to 2950 from management tools, switch is unreachable, I have to access from other switch and reload 2950.
Problem only is from managemt tool to managament vlan 1 2950.
The strange thing is that management interface is encountering a very fast increase of throttles, broadcast and ignored packets:
2950#show interfaces vlan 1 Vlan1 is up, line protocol is up Hardware is CPU Interface, address is 0023.3488.fd65 (bia 0023.3488.fd65) Internet address is xxxxxxxxxx MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255
[code]....
It could be a hardware problem?, IOS has been upgraded.
Is it possible to assign 2 ports to a vlan on this switch and have the 2 machines connected to those ports be able to see each other without having to go off of the switch? If so, how would it need to be setup on the switch?
In my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
I am administering a Catalyst 2960S switch and I would like to connect several computers to it. Some of those each have a static IP address. For a few of them, I would like the switch to dynamically assign an IP address to them via DHCP. Is the switch capable of doing this? If so, how can I do it? I tried looking through Cisco Network Assistant and I couldn't find it. Some web pages have suggested I telnet into the switch and issue commands like "ip dhcp ?" to see what commands are possible. I can telnet in and if I type but I get an "Unrecognized command" for both "ip ?" and "ip dhcp ?". This makes me think I'm reading the wrong web pages. I did come across the term "DHCP snooping". It seems relevant, but very difficult for me to grasp.
we are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950 S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end 3750 SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
I am looking into the possibility of using private vlan's for some dmz implementations however I do have what may be some very rudimentary questions. It seems straightforward how to configure the primary/secondary vlan configuration as well as associating them. However in my case I would be looking to configure the PVLAN on a 6500-vss platform acting as the router while all of the hosts which I would desire to have in the isolated vlan would be spread out across a number of older Cisco switches which only support "protected port" setup or Procurve switches all of which I do not have budget to replace with something newer. So in my scenario I would have a 6500 connected by trunk to multiple switches which only support a protected port setup such as a Procurve (top of rack) or a Cisco 2950. As the Procurve or 2950 would not support Private VLAN setup, do I then just configure the secondary vlan to be allowed across the trunk from the 6500, configure that vlan on the Procurve or 2950 (as vtp will not foward the info for the secondary vlan) and assign that vlan to the host port as well as setting it as a protected port and this will communicate just fine across the trunk to the router as well as stopping the protected port in top of rack switch 1 from being able to communicate to a protected port in top of rack 2,3,etc? If the above scenario is what needs to be done, do I just use a regular trunk or do I have to use a PVLAN trunk?
recently i just connected a non cisco ip phone(from panasonic) to Cisco 2960 POE switch at site A. The PABX system is located at site B,Site A and site B are connected using MetroE Point to point.I would like to apply QoS for voice vlan. I want to assign 2MB to the point to point connection for voice vlan.
I have a Cisco SG 300 28 port switch that I have set in Layer 3 mode. I set up a second VLAN on it (vlan 4). I also set up the scope for DHCP on a Windows server for both VLAN's. The problem I am having, is that VLAN 4 is not pulling DHCP at all. The DHCP server is connected to port 1 on the switch, and the specifics are as follows:
I got some problem with enabling dhcp snooping on 4500 (cat4500e-lanbasek9-mz.122-54.SG.bin) the topology is as below: dhcp snooping enabled only on CORE (with interface trusted to dhcp server)the problem is that I put these 2 commands
ip dhcp snooping ip dhcp snooping vlan 1
but it is not enabled on any vlan
SW-CORE#sh ip dhcp snooping Switch DHCP snooping is enabled DHCP snooping is configured on following VLANs: none DHCP snooping is operational on following VLANs:
[Code]...
On B1 if I turn it on there is a "1" in the section " DHCP snooping is configured on following VLANs:" but on core no.As you can see I did put the trusted on the interface in the direction to the dhcp.First I thought it can be a problem with option 82, I've read a lot about the issues with that, but the problem would be explicable if the client did receive IP address, but it does.
1 Cisco switch stack (SGE2010) in L3 mode, 2 Vlans.
Vlan 1 = 192.168.0.253/24, untagged on all ports except 14/15 Vlan 2 = 192.168.22.1/24, untagged on port 14 and 15 SGE2010 default route 0.0.0.0/0 next hop 192.168.0.1 (Checkpoint UTM) DHCP Relay enabled DHCP server set to 192.168.0.16 DHCP interface set to Vlan2
[code]....
Expanding the ICMP entry, it appears that the destination is the pc client since it shows a Dell mac address, and the source is the Checkpoint UTM (Sofaware).
I can ping and tracert from the Checkpoint to my static IP on Vlan 2. The same goes for the DHCP server to/from Vlan2, so I am confused as to why the routing is failing. I have tried adding Port Fast to the stack ports, but nothing changes.
I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17 ( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself) Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2 ip address 172.16.0.30 255.255.255.240 ip helper-address 172.16.0.17 interface Vlan3 ip address 172.16.0.46 255.255.255.240 ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
ON ASA, I understand that we can assign a static IP for a specific VPN client, or we can use a DHCP pool to assign IP. Now if I want to create DHCP pools, say pool_A and pool_B, for user A, B and C they use the IP from Pool_A, and user D, E, and F they get the IP from pool_B. Is there a way to do this in ASA?
How do you assign each customer to a vlan ? and what kit do you use at the core to roll out VLANS to each pop? We are thinking of using Juniper kit - putting customers on there own VLAN, and having a managed service like TR-069 on those VLANS.Is it do-able and what does everyone use for a TR-069 server - I've been looking on the net and havent had much joy in finding a server - or is it not as easy as I understand it to be.
I know DHCP can assign more than just address, mask, and gateway. It can also assign a hostname, and DNS. Does anybody know if it can also be used to assign an SNMP address?
I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
I need to configure a Cisco 2911. I need to give an interface in this module (VWIC3 - 4MFT-T1/E1) an IP address. My question is, how to assign an IP to an interface in this module.
My purpose is to get connectivity via T1 line to another router.
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
I have a server windows 2008 that I would like to have a nic teaming configuration, the server has two nics, each nic is connected to a different switch. One is connected to cisco 2960 and the other is connected to cisco 2950. I have read here in forums about nic teaming but using the same switch. I have not found using different switch. Is this possible?
