I need to configure a Cisco 2911. I need to give an interface in this module (VWIC3 - 4MFT-T1/E1) an IP address. My question is, how to assign an IP to an interface in this module.
My purpose is to get connectivity via T1 line to another router.
Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies View Related how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.
View 1 Replies View RelatedI am trying to harden my Nexus box and I am not able to ACL assigment command. Following are the commands I am trying to add.
interface cmp-mgmt module 5
Ip access-group NETWORK_MANAGEMENT_ACCESS in
I am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
Need to confirm about 2911 isr, what interface numbers are given to a 9esw when placed in the far left hwic slots (hwic slot 2+3).
I need to build some configs but its going to be a few more weeks before the kit arrives.
I have been having following situation on my WAN facing interface on Cisco2911 where the same number of broadcast, multicast and unknown protocol drops is happening. Not sure but some applications are struggling to run over on the WAN.
[code]....
I have been making effort to solve frequent input errors of module interface(WS-X4548-GB-RJ45) in our Backbone Switch(Cat4506).Let me show you show interface information.Rx-No-pkt-buff value is increased continuously even though traffic rate of interfaces is lower than 20Mbps.We have two Backbone Switch which is operated by HA via HSRP.What bring buffer shortage to our network ? [code]
View 2 Replies View RelatedI have both a Easy VPN server and a site-to-site VPN on the same outside interface of a 2911 router.
Currently, a Easy VPN client has no route int the router then out the site-to-site VPN to the remote site.
How can I create this route?
[code]...
I have a 1t3/e3 card in a new 2951. When I statred the router, I found no interface corresponding to this module when do "show ip interface brief"
View 3 Replies View RelatedI have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies View RelatedWe got a new Cisco 2911 router (CISCO2911/K9) with a switch module (SM ES2-16-P) on it. Everything works fine after the configuration except for the power. We got 4 WAP that we will connect to the switch module that needs power. So the switch module with POE doesn't give any power out.
[code]....
Stumped again with my Catalyst 2950. Everything is working perfectly with wan/dhcp/router on fa 0/1 with all ports assigned to vlan1. All devices plugged in connect to the router correctly with ip's being assigned via dhcp.Instead of hooking up by console port I want to be able to SSH or telnet in to the switch using any port while still maintaining the above functionallity. Is it possible to assign a dhcp assigned ip address to vlan 2 and have vlan1 and 2 bridged? Or is there a better way of doing this ?
View 3 Replies View RelatedActually i have 7600 router and all trafic passes through Gi0/1(Routed port) interface to 6500 series switch. I need to create a vlan on this router eg. vlan 10 Any how it is possible assign a vlan to routed port and traffic of wan interfaces and the vlan traffic passed together.
View 2 Replies View RelatedI wish to assign a MAC ACL to a layer 2 interface on an 887VA router but cannot seem to see how to do this.
View 2 Replies View RelatedI have a question regarding mlppp and bonding mpls T1 circuits. For the longest time we have been able to get by on one T1 circuit coming into our 3845 router. Well this T1 has now become congested and they are wanting to add bandwidth to this T1. We connect to the phone company via an MPLS T1 currently. So now it appears as though we are going to purchase another MPLS T1 circuit and bond the two T1's together. The way our network is currently set up, we utilize the same AS number on all of our remote routers regardless of location. Keep in mind I don't have any sort of mlppp set up at this moment, so unfortunately I can't post any configs. I'm just questioning the design portion and how to go about doing this.
Here is where my dilemma begins........
For every MPLS circuit we order on the remote end, we specifiy an IP for the remote router itself and one for the provider to assign to their equipment (the bgp neighbor statements). Now granted i'm no BGP extraordinaire, not even a novice really, but I don't understand how I am going to bring two T1 circuits into the same router (basically with 2 pairs of IP's). In order to bond the two T1's together, i'll need to create a multilink interface and assign an IP to that, but yet I still have 2 SETS of ip addresses. And if that isn't enough of a dilemma, I also need to spedify a neighbor statement in order for my AS to bind to the adjacent provider AS, but yet I have two IP addresses for that as well.
Is it possible to assign 2 ports to a vlan on this switch and have the 2 machines connected to those ports be able to see each other without having to go off of the switch? If so, how would it need to be setup on the switch?
View 4 Replies View Relatedcant assign cisco switch 3560G port g0/1to access vlan 10
main-switch(config-if)#switchport access vlan 10 Command rejected: Gi0/1 not a switching port.
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedI have ASA 5505 with base license. I created 3rd vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
Code...
How do i tell my firewall to start listen also on another outside ipadress assigned by my ISP? I have it used on other firewall right now. So my steps would be shutting down ip address assignment off old firewall interface. Assign that ip address to ASA5510 outside interface and configure NAT.
View 13 Replies View RelatedI am administering a Catalyst 2960S switch and I would like to connect several computers to it. Some of those each have a static IP address. For a few of them, I would like the switch to dynamically assign an IP address to them via DHCP. Is the switch capable of doing this? If so, how can I do it? I tried looking through Cisco Network Assistant and I couldn't find it. Some web pages have suggested I telnet into the switch and issue commands like "ip dhcp ?" to see what commands are possible. I can telnet in and if I type but I get an "Unrecognized command" for both "ip ?" and "ip dhcp ?". This makes me think I'm reading the wrong web pages. I did come across the term "DHCP snooping". It seems relevant, but very difficult for me to grasp.
View 9 Replies View RelatedOur ISP hands us an ethernet link. ISP router has one address of (for argument sake) 1.1.1.0/30 net, - let's say they have 1.1.1.1 we have the other usable address of 1.1.1.2/30 assigned to our 3825 router. Is it possible to use hsrp or vrrp if there is not two valid/unique "wan" IPs to assign to our routers? For example, if we had a pair of 3825 routers? are we stuck with basically a manual failover or requesting our isp to provide a larger address wan block?
View 2 Replies View RelatedI am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
I am tasked with configuring a 2504 wireless controller. Is it possible to assign an SSID to an interface that has dynamic ap management enabled?
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
i downloaded and transfered the new ios to the 2911, but no install routine started.
View 3 Replies View Relatedafter installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
View 1 Replies View RelatedHow do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies View RelatedI have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
View 21 Replies View RelatedI have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies View Related
