Cisco Switches :: SG300 / Assign Static Ip Address On Vlan 1 Interface?
Dec 13, 2011
I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
View 3 Replies
ADVERTISEMENT
Jul 19, 2012
I have just purchased a SG300-28P switch I am using a GUI to do my config. I cant create VLANs just fine on this but I can not assign IP address to the VLANs.
I just want to have a Data and Voice VLAN on this I am planning on leaving data on VLAn 1 but I can't seem to find an option to assign an IP address to my voice vlan.
For some odd reason I cant access this switch using a console port.
View 2 Replies
View Related
Jul 27, 2011
We have recently purchased a Cisco SG300 and have been configuring it. [code] The VLANs have ACLs set up to prevent any communication between the Holly and Tempo VLANs (and their associated WAN VLANs).Each VLAN has a WAN available for it's use, which connects to external networks (including the Internet).In order to facilitate this, we have set up all the necessary ACLs and routes and confirmed that this all works.However, the problem comes when we assign the static routes that specify the default gateways.We add the two static routes below:
-0.0.0.0 next hop 10.10.200.254 metric 1
-0.0.0.0 next hop 192.168.200.254 metric 1
In this case, only one of the VLANs has WAN access. It is either Holly or Tempo (it can be either if the order the static route is added is changed).What we need is to force Holly to use Holly WAN and Tempo to use Tempo WAN, but we cannot see a way of doing this.Effectively, we want the following static routes: [code]
View 2 Replies
View Related
Feb 3, 2013
i have a SG300-52 Switch, route mode is enabled, and it is using the latest IOS.I have created 4 Vlans in this switch, till this point its OK, but once i try to give ip addres to the created Vlan either from the GUI or CLI the switch is not responding. i have to go and manually reset the switch using a pin.
View 8 Replies
View Related
Aug 1, 2011
model: SG300-52
version: 1.1.0.73
Switch is running in layer 3 mode.How can I turn off mDNS broadcast coming from the vlan interface on the switch.Getting mDNS broadcast from switch every 5 seconds.
View 1 Replies
View Related
Jan 29, 2012
I need to know how to configure each port in switch SG300-10 to vlans, i need to configure one port "trunk" with catalyst switch and assign 4 ports to different vlans. any solution?
View 2 Replies
View Related
Apr 20, 2011
I have what I feel is sort of a strange issue. When I have systems on my home network get their IP from DHCP, they can get to the internet just fine. But it seems that when I assign a static address, they have local network access only, and will not get a connection to the internet. My windows 2008 server is the big problem with this one.
View 10 Replies
View Related
Jun 16, 2012
I know that a default gateway is used to log in remotely, but what is the purpose of the IP address on a VLAN?
View 3 Replies
View Related
Mar 5, 2012
I"m having one problem though. On my old router it had a feature to assign a static IP to a mac address.
So that computer would always get 192.168.10.101 as the IP Address.
How do I do it on this router?
View 3 Replies
View Related
Feb 12, 2012
Actually I have a lab with ACS 5.3 running with 802.1x, but when when the user is successfully authenticated, it's assigned and IP address from the DHCP server, is there a way to assign a static IP address depending of login username??
View 13 Replies
View Related
Oct 26, 2012
I have ASA 5505 with base license. I created 3rd vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
Code...
View 7 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
May 17, 2013
I upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
View 16 Replies
View Related
Apr 19, 2012
I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
View 3 Replies
View Related
May 19, 2013
I'm having troubles with this firmware in a SG300-28 switch. Actually the DHCP server, a new feature in this firmware release, doesn't work correctly. DHCP static reservations are not working: CLient ID and MAC address are not recognized correctly, and the DHCP server assigns the first free IP in the pool, rather than the reserved one.If Cisco engineers read this, plese correct the issue.
View 5 Replies
View Related
Mar 25, 2012
I want to set up a vlan only for the wifi APs and wifi clients on my network. They can't access to any server, only internet acces. I already implement this configuration and its working, but now I want to allowed a couple of laptops to connect to servers in other vlan. what should I do? Should I do it using Mac address of laptops or IP?
View 9 Replies
View Related
Nov 7, 2012
How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies
View Related
Jan 26, 2012
I am using a couple cisco sg300 28P switches along with a sonciwall firewall/router. The sonicwall was already in place and working so they didnt want to replace it. I understand how to configure the vlan on the sonicwall, but could use some info on the cisco. I would basically like to create 3 vlans, 1 default for management, 2 for pc's on lan, and 3 for the cisco spa504g phones/'voip. Would i just go into the vlan managment, configure the 2 new vlans and give them two id's? These offices have one network drop, so the phones and pc's will be sharing the switch ports, however the phones have a setting to configure the vlan id so they know which one theyre on. Is there anything i need to do after that? I want to make sure that vlan 3 has the highest priority becuase its voice, is there some qos configurations i need to make on that switch as well? Also, the port that links the two cisco swtiches together, does that need to be set as "trunk" port? I understand what vlans are, but its just the first time ive run into these cisco models. .
View 0 Replies
View Related
Apr 22, 2012
Before I launch into this can I say that I am very much a novice with regards to Managed Switches and their configuration. I have the following equipment which I have connected to the switch: [code] All of the above are on subnet 255.255.255.0.All of the above communicate with each other during normal operation.Our client is connecting to the switch but his requirement is for his system to "see" the PLC Comms Card as follows:IP: 10.0.3.61 on Subnet 255.255.252.0 .
Using the Internet Explorer interface connection I have created an additional VLAN (ID 2) on Port 10 with the intention of using this as the connection to the client ( I assume there will be further settings required to route the PLC connection to this port) but every time I try to assign the IP and Subnet values and click "APPLY" the changes are not made and the connection appears to hang leading me to reboot the switch.I have connected to the switch via console and changed the mode to Layer 3. I also assume that it is OK for the three pieces of equipment to remain on the default VLAN. How I should setup this VLAN and ultimately achieve my goal.
View 5 Replies
View Related
Mar 28, 2013
I am facing an issue to setup what I initially called simple network but still unable to put it together.On SG300-20 I want to setup 4.3 of the vlan are to separate users in to different groups and to secure data confidentiality.1 is for the NAS. All users on the 3 vlans must access the NAS vlan.All user should have access to internet via SG300 through the ISP provided router. How to configure this, I have every little knowledge of switching and routing? And the routing seems to be the issue I am encountering because I am able to create the VLANs and assign static IP address to them but not able to get them talk to each other. I use each vlan ip as gateway on each port assigned. [code]
View 13 Replies
View Related
May 10, 2013
I want to use Multicast TV VLAN with my SG300-10 to join Multicast Groups in different Data VLAN's. It's working fine, but the problem is that it isn't possible to add all the Multicast Groups to the Multicast VLAN because each TV channel use other groups. For me it's only to handle if I can use wildcards to add a specific range of multicast traffic to the Multicast TV VLAN. Is that possible with that Switch?
View 1 Replies
View Related
Feb 19, 2013
i purchased 300-28 how it config for stp and trunk
View 2 Replies
View Related
Mar 31, 2012
We have recently purchased a SG300 to break up our network which most consists of virtual machines via Bridged networking on network machines. I have created successfully Vlans and the physical machines are capable of communicating across the different subnets that I have created via the SG300 however the Virtual machines can no longer be reached.
View 2 Replies
View Related
Jun 24, 2012
I have one question regarding switch sg300-10. How can i check current interface utilization in bits/second? If I use show int counters I can only see number of unicast, broadcast and multicast packets....plus total packets. But there is no info regarding input and output rate for particular interface (like in original IOS when using show interface command).
View 3 Replies
View Related
Jun 6, 2012
I have a connection on IP 192.168.1.21, Subnet 255.255.255.0 - this is on the default VLAN1 on the switch. I need to route this to IP 10.0.3.101, Subnet 255.255.252.0 - which is set up on VLAN2 on the switch. I have set the switch to Layer 3 via console.
how I setup this route? I am use the Browser based interface.
View 15 Replies
View Related
Sep 11, 2012
I am wondering what the best way to separate a network, both data, on a cisco SG300. I do not want network 1 to able to communicate with network 2 or vice versa. I have one server for DHCP for network 1, 192.168.1.X. I would like network 2 to have ip of 10.0.0.X, can the cisco SG300 do dhcp for this vlan?
View 1 Replies
View Related
Jul 13, 2011
Using a sg300-52 switch I created two VLANs that share a port for access to the internet. All original devices added to the VLANs are functioning correctly so I have to beleive the VLANs are set up correctly. I added a new desktop and an old laptop to the VLAN and neither worked. I was able to get the desktop to work by enabling VLAN tagging in the network adapter. The laptop is 5 years old and it does not have any such setting in network adapter. There are 2 other devices that share the same port with the laptop and they both function properly. My conclusion is that the laptop does not support VLAN tagging. Is there someway to configure the switch to account for this?
View 6 Replies
View Related
Mar 4, 2012
i was trying to set up a new SG300-52 L3 switch for switching and Vlan. The problem is that the vlans on this switch cannot get their DNS resolved. Probably a stupid thing i can't get to see, but i think it is a simple solution given switchin is not my expertise.So my setup:
- ISP Wan router: LAN ip 10.0.0.1, DMZ: 10.0.0.2 -> i have to use this router for ISP support. But it suckes, that's why we use own router for firewall, port forwarding etc.
- Nice Router: WAN: 10.0.0.2, LAN: 192.168.1.1
- SG300 L3 switch
This works. I can ping switch, nice router, ISP router and google's ip from VLAN 5.But i cannot ping google using host name. From within SG300 i can. So it has something to do with SG300 not doing DNS right.My Client on VLAN 5 has ip 10.1.1.5 / 24, default gateway and dns pointing to switch: 10.1.1.1.I have put an entry in DNS servers in SG300: 192.168.1.1 active (pointing to Nice router). On client leave default gateway pointing to switch. But put DNS server : 192.168.1.1
View 11 Replies
View Related
Mar 25, 2012
I set an SG300 switche in layer 3 mode with 3 vlans.I need to give IPs to a whole vlan machines. Do the switch have a DHCP server per vlan? How to configure this?
View 3 Replies
View Related
Mar 17, 2012
configure my new SG300-28P. When I have started the switch, I have specified a new password and enabled telnet in order to setup the switch in Layer 3 mode.
After a restart, the switch took its IP address from a DHCP server. When I try to set a static IP address (192.168.2.1), I receive the following error message: Duplicated IP interface on the same subnet.
The IP address 192.168.2.1 is not used by any device within the network. For information, the message doesn't appear when the switch is in Layer 2 mode.
why I can't change the IP address of default vlan in Layer 3 mode ? All I can do is set the IP address to static or dynamic.
For test purpose, I have added 2 vlans. But I wasn't able to route traffic between vlan. how to configure the switch to route traffic between vlan?
find below details informations about my VLANs.
- Default (VLAN ID 1)
IP Address : 192.168.2.1
Subnet : 255.255.255.0
[Code].....
View 3 Replies
View Related
Dec 21, 2012
I have a new SG300-28P, and have had occasional issues with being unable to connect to it via anything other than the serial port. I have connectivity between my machine and the switch (tested with ping each way), and in fact, have the same problem if I take a laptop to the switch and connect them directly.What happens is that though the switch is operating normally, http, https, ssh and telnet attempts to access all fail in one way or another. Ssh and telnet either yields no response or a refused connection (even though those services are enabled). For http and https, I'll occasionally get enough of the web page to be able to tell what it is ... but attempts to log in just don't work.While this is happening, the CPU and packet load on the switch is very, very low.Rebooting didn't work entirely, though it may have made it better. Resetting to factory defaults and then reconfiguring makes it work.This is using the latest firmware: 1.2.7.76.
View 3 Replies
View Related
Sep 4, 2011
Any snmpset commands to modify port vlan membership on SG300-28 switches? I checked [URL] however this information is apparently only valid for catalysts.
The latest firmware is installed and the provided MIB files are used.
View 5 Replies
View Related
May 15, 2013
we have an SG300 latest 1.3 firmware, we have it acting as our DHCP server, we have a 10.10.1.x range, 10.10.3.x range, and 192.168.24.x range, they are all on seperate VLANs and all can talk to each other which is what we want. However we have someone who wants to use the 192.168.1.x range to add IP cameras to our network using there own switch. I figured I'd just setup our server to do DHCP etc and it would communicate with the 10.10.1.x range of IP addresses no problem. It turns out the SG300s can't do DHCP for that range, so if he has all static address on the 192.168.1.x range how can i setup inter VLAN communication so we can talk to that range?
View 1 Replies
View Related
