I"m having one problem though. On my old router it had a feature to assign a static IP to a mac address.
So that computer would always get 192.168.10.101 as the IP Address.
How do I do it on this router?
I have assigned a Static IP with other Linksys/Cisco wireless routers (WRT54G), but I can't seem to get the E4200 to assign a Static IP. My device is connected to Port 3, with that being the only port (besides my WAN) being occupied. When I enter the following and click Save Settings I get the following error: "Invalid Static Route!"I don't understand what I am doing wrong. This is the exact same as I have done on my WRT54G and it worked.
View 2 Replies View RelatedI have what I feel is sort of a strange issue. When I have systems on my home network get their IP from DHCP, they can get to the internet just fine. But it seems that when I assign a static address, they have local network access only, and will not get a connection to the internet. My windows 2008 server is the big problem with this one.
View 10 Replies View RelatedI previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedI am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
Actually I have a lab with ACS 5.3 running with 802.1x, but when when the user is successfully authenticated, it's assigned and IP address from the DHCP server, is there a way to assign a static IP address depending of login username??
View 13 Replies View RelatedOn my EA4500 i've given my Sony Google TV Box (connected by wifi N) a static ip address under "DHCP Reservations". However is there any way to add a DNS server address to this reserved IP so that only the Google Box is affected by the DNS, all the other connected devices remain unaffected? Presently i enter the required DNS address in the google box but i would prefer to do it on the EA4500. I'm using the latest Cisco Cloud fw on my router.
View 3 Replies View Related2 of my attached wireless devices have the same IP address different MAC address. How can I assign unique address to each of the devices
View 1 Replies View RelatedI recently switched cable companies and was given a Linksys E1200 wireless router to connect to the internet. The router works fine with all of my laptops but not with my desktop. The desktop has a WMP11 wireless PCI card. I have had trouble using this card in the past but have always managed to solve connectivity issues. This time, I am unable to connect to the internet. Although I can detect the network signal, the network will not assign my computer an IP address. Also, when I first switched routers, I got a message saying I did not have the proper certificate to connect to the network
View 1 Replies View RelatedEverything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access. We have a statis IP assigned by our ISP solely for this purpose. For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing. When we hard line into the modem, we are able to browse it fine. When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it. We had set it up about a year ago, and i completely forgot how.
View 2 Replies View RelatedI am thinking about purchesing this router. But I need know if this router has DHCP reservation function. If router can assign to specific MACs their own IP adress. I had WRT160N for a week, but my ISP change technology. WRT160N had this function, but I am reading here, that WAG160N not.
View 5 Replies View RelatedI have a WAG 120N Modem Router, My question is: Can you assign an static IP to a pc using this router?
View 2 Replies View RelatedI have a problem viewing my security cam on my android IP cam app.I forwarded port on my router to my security cam then fixed security cam to have a static IP but my computer being on DHCP, after reboot changed IP, so I lost connection to android IP cam app.I read on a forum,that If your camera is using DHCP,setup your router so that it always gives the same static IP address for the camera based on it's MAC address but where do you set this up a Linksys E1000 router & on Samsung Y? so I can view my security cam on my android IP cam app.?
View 9 Replies View RelatedI have a Swann Communication security camera system with their DVR8-4000 hooked to an IPv4 router, connected to the Internet using the new HughesNet Gen4 service. The Swann DVR wired to my router requires a static IP address. HughesNet Gen4 is implemented with IPv6 and I am told that it does not accommodate an IPv4 type static address.
I have discussed the issue with both company’s technical support. HughesNet Gen4 reps recognize the issue and may support static addressing in the future, but not now. Swann reps will not modify their implementation because of the relatively small Gen4 market. The Swann rep suggested that replacing my IPv4 router with an IPv6 router might resolve the “static IP address” issue.I am looking at several Linksys IPv6 routers including the EA4500 SMART WiFi Wireless Router N900, but know too little about IPv4, IPv6 and router/static addressing to proceed unassisted.
1) can I implement a static address with an Linksys IPv6 router cdonnected to Gen4?
2) Which Linksys routers offer IPv6 support?
3) How does one go about setting an IPv6 static address using HughesNet Gen4 on a Linksys router?
Ok so I have a couple devices connected to it, but there's a trick with Android phones that users report better battery life assigning an Static IP to the phone, not dhcp or reservation. However I can't figure it out in this router as when I revoked the current address it wouldn't let me add a new one, and when I went to add one at .202 to be outside of dhcp range it doesn't let you and says to enter a number within the range, .100-.199
View 6 Replies View RelatedMy printer (HP7210) is wired connected to my WRT54GL router. 2 computers have also a wired connection, my laptop is connected wireless. All these computers use the connected printer. 2 computers can only use a static IP-address for the printer. How can I set a static IP address in my router?
View 3 Replies View RelatedThere are 6 computers in our home network. It happens every few months or so that router would not assign valid IP address to one of the computers. So, most of the time everything works well, but there comes a moment when one of the computers (but not others) can't get valid IP address.We try turning off and then on the router and it solves the problem most of the time. But, there are cases when turning off and on the router won't solve the problem.
View 3 Replies View RelatedI'm adding another router to my home network to extend my WiFi range. (Linksys e2500.) I'm trying to change its IP from the default 192.168.1.1 so that it doesn't conflict with my primary (dhcp) router.
To isolate matters I've reset the router to factory settings, turned off my mac's WiFi and then connected the Mac to a Lan port on the router. Now I can view the router's admin page at 192.168.1.1.
Now I change its local IP to 192.168.1.3 and leave the subnet as 255.255.255.0. The router reboots and after several minutes is inaccessible at any IP I try (still hardwired to the Mac with WiFi off). Ifconfig doesn't show the router and the only way I can get it back is to factory reset it again.
Is there an alternate way to get the DNS settings off of the router? I've followed all of the steps up above, but I cannot set up a static IP Address on my computer without knowing the routers DNS settings, which I cannot retrieve from the web-based setup due to the corrupt firmware.
View 2 Replies View RelatedI have a public IP and I want to be able to view my three systems connected to a linksys router from the internet. How can configure the router to see three systems with just one Public IP address whenever I am on the internet?
View 5 Replies View RelatedIt took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
View 1 Replies View RelatedMy system is in LAN. IP is assigned by DHCP. Now i want to assign a STATIC IP to my system. There is no direct connection from vendor router to my PC. My network path is like this. From ISP vendor to Switch->Firewall-> LAN switch. how can i configure Static IP in my PC..
View 4 Replies View RelatedI've been given 4 more public static ip's and would like to use one of them static ip's to point to my sharepoint box, for example i want to be able to access my sharepoint boxweb site externally:
212.xxx.xxx.01 - my public pix ip
212.xxx.xxx.02 - is my owa for email (https://xxxxxxx.net/owa)
212.xxx.xxx.03 - my sharepoint box (https://xxxxxx.net/sharepoint)
212.xxx.xxx.04 - not assigned
What command do I have to input on the Cisco Pix 515 to make that work?
i have a ISDN connection i have got 1 static WAN ip and 7 static LAN ip . i have connected it to a server 2008 r2 given that the WAN ip and shared it how do i assisgn 7 LAN static IP in local area network
View 3 Replies View Relatedwith my broadband internet I received a range of 5 IP addresses from BT. I would like to assign one of them to the modem, in order to reach the modem from the outside using that IP.,Is this theoretically possible at all?,Is the WAG320N supporting static IP addresses with PPPoA at all?,When I select PPPoA as the encapsulation on the Setup/Basic setup tab, I cannot enter an IP address on that tab. I tried using the Setup/Ethernet tab, but selecting ""Use as a WAN port", "Static IP", inserting the IP and clicking on "save" result in a cut of the internet connection.
View 3 Replies View RelatedI want to assign static IPs to users that login to IPSec VPN using Group Authentication in ASA 8.2. The authentication through a Windows RADIUS server. Right now, they are connecting just fine and pulling an IP from the pool I have configured in the IPSec policy.
What would the best way to assign static IPs through VPN?
I have a E2500 router and 3 WAP610N access points. Users are having a difficult time connecting to the AP's. The client device just sits there trying to obtain an IP and then times out. If they get within range of the actual wireless router, then connect instantly. Is there a setting to increase that will allow longer time trying to obtain an IP?
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap. See diagram below. Not sure if this has some impact?
We have a Highly available VPN infrastructure across two data centers. We also use ACS 4.2 servers for authentication. The ACS servers are in teh same "cluster" in a Primary and Secondary fashion. Site A has primary ACS and primary ASA 5550 IPSec VPN termination. Site B has secondary ACS and redundant ASA 5550 IPsec VPN termination. We also use InfoBlox for DHCP IP address assignments. The two IPSec VPN Head end devices, ASA 5550s, they use different subnets for IP pools for the VPN Clients. Site A uses x.x.24.0 and Site B uses x.y.24.0. As indicated VPN clients authenticate using teh ACS 4.2 Radiius server. I can assign static IPs per user on the ACS server but this can only work for the primary site. Once static IP address is assigned on primary ACS for a user, this status will be replicated to the secondary ACS on Site B. When the Primary IPSec VPN Head End ASA or Internet fails on Site A, Clients on DHCP will work fine seemlessly via Site B. But for the static IP users, you have to change the Assigned Static IPs to match the subnet on Site B. How I can assign static IPs to clients via both Sites without manual intervention. Either via DHCP or ASA. I was trying to stay away from creating multiple Groups for VPN and also avoidng creating local ASA users because these options will not scale well as static user base increases. I need users to get a static IP address from Site A subnet when connected to Site A and get a static from Site B subnet when connected through Site B.
View 1 Replies View RelatedI upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies View RelatedIs there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
Could I use DHCP for wireless connection and assign private IP for PC for wire connection ?Will it conflict to each other ?
View 3 Replies View Related