Linksys Wireless Router :: E1000 Static IP Address For Security Cam App
May 2, 2012
I have a problem viewing my security cam on my android IP cam app.I forwarded port on my router to my security cam then fixed security cam to have a static IP but my computer being on DHCP, after reboot changed IP, so I lost connection to android IP cam app.I read on a forum,that If your camera is using DHCP,setup your router so that it always gives the same static IP address for the camera based on it's MAC address but where do you set this up a Linksys E1000 router & on Samsung Y? so I can view my security cam on my android IP cam app.?
View 9 Replies
ADVERTISEMENT
Jun 18, 2012
Your product is stable but not profitable For the price your customers is easier to buy a model Zyxel Correct firmware for the static route, or Dynamic Routing (RIP)LinkSys E1000 Enabled - Dynamic Routing (RIP) NO RESULTS!ZyXEL KEENETIC LITE - automatic routing!
View 9 Replies
View Related
Jun 26, 2012
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
View 4 Replies
View Related
Aug 21, 2011
I have a Linksys E1000 wireless-n router. I bought the router originally so I could get my Nintendo DS on Wi-Fi. I then realized that DS games require a WEP Key, but my E1000 defaults to WPA/WPA2 mixed mode. My laptop and my Wii connect online with the default settings just fine. My 3DS also seems to be able to connect with the internet router, but not Wi-Fi, for some reason. So when I'm on Cisco connect, I go to Router settings, it brings my web browser to "http://192.168.0.1". From there I go to the Wireless tab, and then click on Wireless Security. I've tried multiple times to change the Security Mode to WEP, and even disabled security. But after I save the settings, the connection on my laptop is lost, and I have to reboot my router all over again, and am back with the default WPA/WPA2.
View 1 Replies
View Related
Jan 19, 2011
I just want to allow specified computers wired access to the internet via the E1000 router. Here is the problem I am currently working on:
(1) Setup the E1000 unit to allow only one PC 'C1' (MAC: 91:E6:BA:25:91:58) wired access to the internet.
(2) Add another PC (unknown MAC address) to the LAN side of the E1000 unit and see if it is being blocked by the 'Access Restriction' policy that was setup.
(3) Can’t get the above done – the second PC is able to surf the internet although the policy is enabled.
Notes:(a) Ref: 'Access Restrictions' web page or see Page 26 in the User Guide .(b) The unit has the latest firmware already installed: Firmware Version: 2.1.01 build 5Dec 3, 2010.(c) The internet port of the unit goes to the ADSL modem in my house.(d) Unplugged the unit for 10 seconds as advised by one of your technicians, still no difference.(e) I can deny PCs, but the allowing only specified ones seems not to be doing anything.By the way, can the E3000 or E4200 do the above?
View 9 Replies
View Related
Apr 25, 2011
Does the E1000 router come with a default security setting upon installation using the supplied CD?
View 9 Replies
View Related
Dec 31, 2011
Having just installed the E1000 why have I got a public network address '####' which is security type WPA2 -PSK and also public network address '#### - Guest' which is security type - unsecured.Anyone can log onto either wireless network connection but only with the correct password.How do I remove the '####' address and also how do I make the '#### - Guest' address a secure one.
View 1 Replies
View Related
Mar 5, 2012
I"m having one problem though. On my old router it had a feature to assign a static IP to a mac address.
So that computer would always get 192.168.10.101 as the IP Address.
How do I do it on this router?
View 3 Replies
View Related
Apr 10, 2013
I have a Swann Communication security camera system with their DVR8-4000 hooked to an IPv4 router, connected to the Internet using the new HughesNet Gen4 service. The Swann DVR wired to my router requires a static IP address. HughesNet Gen4 is implemented with IPv6 and I am told that it does not accommodate an IPv4 type static address.
I have discussed the issue with both company’s technical support. HughesNet Gen4 reps recognize the issue and may support static addressing in the future, but not now. Swann reps will not modify their implementation because of the relatively small Gen4 market. The Swann rep suggested that replacing my IPv4 router with an IPv6 router might resolve the “static IP address” issue.I am looking at several Linksys IPv6 routers including the EA4500 SMART WiFi Wireless Router N900, but know too little about IPv4, IPv6 and router/static addressing to proceed unassisted.
1) can I implement a static address with an Linksys IPv6 router cdonnected to Gen4?
2) Which Linksys routers offer IPv6 support?
3) How does one go about setting an IPv6 static address using HughesNet Gen4 on a Linksys router?
View 1 Replies
View Related
Nov 10, 2011
My printer (HP7210) is wired connected to my WRT54GL router. 2 computers have also a wired connection, my laptop is connected wireless. All these computers use the connected printer. 2 computers can only use a static IP-address for the printer. How can I set a static IP address in my router?
View 3 Replies
View Related
Feb 27, 2012
I HAVE A CISCO E1000 WIRELESS ROUTER. I KEEP GETTING "NEED WIRELESS SECURITY SETTINGS FOR MY ROUTER NAME. CONNECTING FROM HP-XP INTERNET TO MY LAPTOP HP-VISTA. I HAVE ENTERED:
SECURITY TYPE: WPA2-PERSONAL
ENCRYPTION TYPE: TKIP
NETWORK SECURITY KEY: ???????
THIS IS WHERE I AM STUMPED AT NETWORK SECURITY KEY. I TRIED WHAT I THOUGHT IT WAS FOR MY LAPTOP HP VISTA, BUT IT'S NOT EXCEPTING. I'VE BEEN AT THIS FOR 2-WEEKS TRYING TO FIGURE OUT HOW TO GET MY VISTA TO WORK WITH MY XP. WHERE DO I GO TO GET A NETWORK SECURITY KEY???
View 2 Replies
View Related
Jun 22, 2011
I have enabled DHCP but want to set static table IP's for my security camera DVR and one computer, the others can remain dynamic. I know in other routers I can attach a LAN IP to a mac address to keep it static but I can't see where I can do that with this router.
View 4 Replies
View Related
Jul 3, 2011
Is there an alternate way to get the DNS settings off of the router? I've followed all of the steps up above, but I cannot set up a static IP Address on my computer without knowing the routers DNS settings, which I cannot retrieve from the web-based setup due to the corrupt firmware.
View 2 Replies
View Related
Sep 11, 2011
I have E4200 with fixed ip 192.168.1.2, DHCP off connected through LAN ports to FIOS ActionTec as 192.168.1.1. When connecting through wireless network off the E4200, I can obtain and connect fine under Guest network and WEP security, but for any other security setting, WPA, WPA2, Mixed mode, etc. I get the message "Aquiring network address" forever, and I never get a connection.
View 1 Replies
View Related
Sep 5, 2011
enable security with linksys e1000. it has a password key before but it automatically disabled.
View 1 Replies
View Related
Apr 3, 2011
Is there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
View 1 Replies
View Related
Mar 26, 2012
I own a E1000 router that I use with several wireless machines. Unfortunately, I cannot connect to the configuration of the router by typing url...in a browser, be it wireless or weirdly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router". I tried to switch my router off and on, but that doesn't work. Totally resetting the router solves the problem, but not definitely.Is there a solution that does not require resetting my router?
View 2 Replies
View Related
Dec 20, 2011
My guest can't use my wireless network and I can not add more devices like a ipad2. Got a new ipad2 for my son for Christmas been trying to set it up for Christmas, so on Christmas day I am not trying to do the set up. My problem is I can not get it to log on to the network. I have been putting in the same pass word all my other computers in the house use but it will not work...
View 2 Replies
View Related
Feb 10, 2013
My wireless router (E1000) was accidentally unplugged. Since then the wireless LED light doesnt come on and the router cannot be detected. All the other lights are on. I tried to reset it but I dont think it worked, since the power LED didnt blink as its supposed to do after holding reset for 10-15 seconds (or more!!).
View 5 Replies
View Related
Aug 9, 2011
I've been using the E1000 for months. I have 2 iphones, an ipod, a windows 7 netbook and a macbook connected wirelessly to it. It's been set at wpa2/wpa mixed mode all this time without a problem. Out of the blue: no wireless connection on any device. I restarted the modem, router, PC's, phones, etc. I've updated the firmware. The only way I can get a wireless connection is to use wep. How can I get the better security and speed of wpa2 back?
View 4 Replies
View Related
Feb 21, 2012
I am trying to access the internet with my ipod and it is picking up my wireless connection but it is asking for a password, how do I get my password. I don't remember seeing a password when I hooked up my router several months ago. I called Cisco for some technical support but they wanted money to get me and I am not paying them a dime.
View 1 Replies
View Related
Jul 3, 2012
I can setup my router with the cd
View 1 Replies
View Related
Jul 26, 2010
I have a PS3, and i play allot of video games such as all COD game especially MW2. It says i have a strict or moderate NAT. My router is in the same room as the PS3, so i should have a Open Nat.Also i have another question, i bought this Epson printer from Best Buy, i was wondering if I can connect to it Wireless, but i think i cant connect to it wireless cause i dont see the WiFi Certification on the printer or anything hints that it can connect wireless
View 9 Replies
View Related
Sep 3, 2011
With the E1000 tthe wireless devices they seem to work just fine, I can access the internet just fine.
For my desktop PC in oder to use the router to get on the internet or to even use the Cisco Connect to check the router, the E1000 needs to be rebooted. I am unable to access the router otherwise. I have tried 3 different LAN cards all with the same results.
The latest firmware notes do not look like upgrading the firmware will work. My Router info from Cisco connect
Model name: Linksys E1000
Model number: E1000
Serial number: CVN21L422937
Firmware version: 2.1.01 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): unknown
View 1 Replies
View Related
Jan 24, 2013
Things seem to slow down significantly to the point of loosing connectiviety. When I check, my mips are 150 or so. Tried disconnecting and connecting again but didn't work. When I power down the router and power it up, I get 300 mps again but doesn't last too long
View 2 Replies
View Related
Dec 30, 2011
A lady gave me E1000 along with an IMB Thinkpad because her husband was the main user on the internet. I have an intel iMac 10.4.11, DSL. I have not yet connected to either device via the router. I am new to wireless routers. I have been to the configuration page
View 2 Replies
View Related
Apr 7, 2013
I have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies
View Related
Jun 23, 2011
I had an E1000 for a couple of years that worked OK. Then it went nuts--sporadically dropped the signal, wouldn't show its web page, etc.--maybe a power surge, who knows? So I tossed it and got a new one on the theory that it would be a plug in replacement .The new unit had a good signal, but also wouldn't show its web page, so I couldn't configure security. I removed Network Magic and everything else I could see pertaining to the old unit. However, the CD for the new unit still gives me: " Your router has already been set up. You need to use an Easy Setup Key that you can use to get other computers connected." Needless to say, I don't have such a thing. Cisco Connect is not installed at this point, so I can't go into it to create one.How can I purge the remains of the old unit so the new one will install properly?
View 6 Replies
View Related
Jul 14, 2011
I have E4200 connected to Internet. It is configured with NAT. My side of the router is set to 10.10.10.0 and DFG is set to 10.10.10.254. Server is connected at 10.10.10.1 and is DHCP host.I now have E1000 that I want to connect downstream side of the E4200 (located on the other side of the building). I want the E1000 to be an extension of the existing network so the whole building looks like one network. I'm not sure how to configure the E1000. I assume I need to disable NAT but I'm not sure how to configure the Internet IP addresses of the router and nro am I sure how to configure the local network side of the router.As I write this, I wonder if I connect one of the Ethernet ports of the E1000 to the E4200 and just leave the Internet side unplugged?
View 2 Replies
View Related
Jun 10, 2010
I'm trying to set up my E1000 router and when I run the Cisco Connect software that came with the router I get a message that says that it can't find the router, I've tried running it with my computer connected to the router and not connected. I've looked through the FAQ section and didn't really find anything. I'm trying to set it up on a laptop, it's a Vaio running Windows 7, I don't if that makes any difference.
View 7 Replies
View Related
Nov 12, 2011
I am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 2 Replies
View Related
Feb 16, 2011
I've been searching off and on for the past couple months trying to figure out what we could do to our router to open our NAT, after having both the PS3 and Xbox 360 tell me I've got moderate NAT. I tried a DMZ with my PS3 having a static IP, I tried UPnP. I messed with firewall settings, to no avail.
I recently found something that did work however, on Google. Basically what happened was, I needed to reset the router and change a few settings on top of enabling UPnP I didn't know about(CTS Protection, remote management) how they could have anything to do with translation of data.
But like I said, after doing a huge step by step walk through, I was able to get open NAT in the network tests of both PS3 and 360(even though the PS3 obviously still says Type 2. It used to say Type 2, but it also used to have an error code at the bottom of the page). I've checked in games on each console, and they tell me I've got open NAT.
Now I still have one tiny problem. Red Dead Redemption. I play Red Dead Redemption online with two friends(who, incidentally, have the same router as me), and we haven't been able to communicate if we were using routers. We still can't, but I'm thinking that it's not my router anymore. I'm thinking his router has incorrect settings. Am I correct?
View 8 Replies
View Related
Sep 21, 2011
So here is the issue:
When I connect my modem directly to my computer (modem > computer) it works just fine, internet connects and everything through the direct ethernet connection.But when I connect the modem to the router and then try to connect wireless with any other computer (modem > router > wireless) nothing works. Not even when I have it connected directly from the router to the ethernet on the main computer. (Which has ALWAYS worked until now.
View 1 Replies
View Related