Linksys Wireless Router :: Cisco E2500 - Using Gateway Address As Browsing IP For Connected Computers

Jan 31, 2013

Everything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access.  We have a statis IP assigned by our ISP solely for this purpose.  For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing.  When we hard line into the modem, we are able to browse it fine.  When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it.  We had set it up about a year ago, and i completely forgot how. 

View 2 Replies


ADVERTISEMENT

Linksys Wireless Router :: E2500 Can't See Other Computers On Local Network

May 1, 2012

I have a E2500 connected to a cable modem as the base of my home network. Hard wire connected to the E2500 is an linksys 8 port hub and a couple of computers. The 8 port hub is connected to a couple of computers and a xbox. I have the hub as a distro point to cut down on wiring. Wirelessly connected to the E2500 are a variety of laptops, netbooks, ipods, an ipad, a playbook, an iphone, a android phone, a wireless printer and a Ps3. Most of the devices are just using the wifi for internet access. Most devices have been setup with their own ip addresses to avoid ip conflicts. The computers and laptops/netbooks are running either Windows XP, Windows 7 or Mepis Linux. Up until now everything was going as good as can be expected, all the computers could see each other and most could transfer files between each other except when Windows gets picky.In the last few days no computers can see each other. Windows or Linux.Everything can accsess the internet and wirelessly print still just can't see each other. I reset the E2500. I updated the firmware on the E2500. I installed the Cisco Connect software (just in case I was too stupid too setup a router). Still nothing. I can ping other machines from a command prompt in windows or a terminal in Linux and get a good ping back. In the router setup via a browser I can go to the status page and see other devices on the local network but most are just ipods, ipad, playbook and the wireless printer, If I go to the administration page / diagnostics I can ping other computers and get a good answer. I just can see them from each other. I think I've rebooted every thing at least once. Yes the workgroup names are all the same (workgroup) and yes file sharing is turned on on all computers.

View 3 Replies View Related

Linksys Wireless Router :: E2500 Doesn't Work With Two Computers?

Aug 1, 2012

I have a mac 10.7.4 and an xbox 360 slim. Whenever  I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.

View 1 Replies View Related

Linksys Wireless Router :: E2500 Blocking Computers From Sharing Files?

Jan 22, 2012

I just installed the E2500 to replace my older router.  With my older router I was able to share files between the different computers in my house.  All I did was replace the old router with the new one and now they cant share files?  I looked through the router settings and cant find anything showing firewall blocking the file and print sharing.  why I cant share the files and how to allow the file sharing? 

View 1 Replies View Related

Linksys Wireless Router :: E2500 Installed Computers Stop Communicating

Nov 21, 2011

I,ve used a network for a number of years with no problems. I have databases on computer 1 and access them with computer 2. After installing a Cisco e2500 I can connect to the databases but after a short period of time I am disconnected. If I search my network computer 1 is not found. Waiting a few minutes the network will find computer 1 again. At about the same time my firewall software has started to show an attack from an 2 different IP's I don't recognize but its always one of those 2 IP's. I'm assuming the two problems are related. I,ve considered going into my firewall and allowing the unknown IP access, BUT who knows where that IP is coming from. I've checked the Cisco setup but couldn't find an IP address that matched the attacking IP address.

View 1 Replies View Related

Linksys Wireless Router :: E2500 And Motorola RG2200C Residential Gateway?

Jan 6, 2013

I am trying to setup a Linksys E2500 router with a Motorola RG2200C Residential Gateway.  The Motorola box provides TV and DSL output.  Currently a Linksys BEFSR81 router is connected and works fine.  With the E2500,  running Cisco Connect it gets to 90% complete and then times out.  I'm guessing at that point it is trying to connect to the Internet.Support had me download the latest Cisco Connect, but it had the same problem.  I have tried various things manually configuring the router with no success.

View 9 Replies View Related

Linksys Wireless Router :: E2500 Disconnects When Connected With PS3

Aug 8, 2011

I am using a E2500 which is connected to my modem arris model tm602g/115 isp provider is cox. for some reason every1 time my lil bro turn on his ps3 and while im connected to the network it will disconnect me and also he gets disconnected and for some reason we both wont be able to connect to internet. we both are using wireless connection.

Here are my settting on the router. I also 3 have iphones that i want to connect the network with any 1 other device that i would like to connect the network with.

View 4 Replies View Related

Linksys Wireless Router :: E2500 What Devices Are Connected

Feb 13, 2012

So i just set up the Linksys E2500 and it shoes 8 devices connected to my router. How I can see what devices are connected?

View 1 Replies View Related

Linksys Wireless Router :: E2500 - Assign Static IP To Mac Address

Mar 5, 2012

I"m having one problem though. On my old router it had a feature to assign a static IP to a mac address.
 
So that computer would always get 192.168.10.101 as the IP Address.
 
How do I do it on this router?

View 3 Replies View Related

Linksys Wireless Router :: E1500 - Internet Slow On 3 Connected Computers

Dec 10, 2012

I have 3 laptops connecting wirelessly to this router.  One is running at 18Mbps, the other two at 0.4Mbps.   the internet setting are the same and the security is the same (WPA2-Personal with AES encryption).  One of the slow computers is brand new and WAY faster than my "fast internet" computer.  The other is about the same as the "fast internet" computer.  I updated the  I connected the new computer to the router tusing an ethernet cable and it had superfast internet.  I redid the Cisco connect on each computer, but it didnt change anything.  Why is it so slow wirelessly?

View 4 Replies View Related

Linksys Wireless Router :: WAP610N - Block Website On All Computers Connected To Router?

Jan 4, 2011

Why there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?

View 4 Replies View Related

Linksys E2500 Router Connected But No Internet

Jul 7, 2011

I bought I router today, Linksys E2500 and set it up, for some reason its connected with full strength but the internet does not work on my computer, or any other device connected to the network I established on the router. I've looked through so many articles and posts on here, I've fixed the winsock, I tried the netsh winsock and the netsh int ip reset reset.log, but when I put in netsh int ip reset reset.log in the command prompt, nothing happens after I press enter. I've updated through microsoft updates, and updated some drivers from the hp website. Ive repaired, and tried restarting the router, and even the modem and nothing changed. It's still connected, but the interenet still is not working. The modem is fine, as when I disable the wireless connection, the internet works. Yes, I have Sp3 installed.I am using windows xp and the computer is called HP Pavilion a1013w Desktop PC. [code]

View 5 Replies View Related

Linksys E2500 Router - Computer Connected But No Internet?

Dec 28, 2011

Well i recently purchased a Linksys e2500 router,so i connect it to my modem and then to my PC, all by Ethernet cable(no wireless) as i want my pc connected by cable, i go through the set up CD and it finishes and says you are now connected to your router but..... not to the internet and it tells me to restart the modem with i have done, i have also tried power cycling modem, router and PC, but i still get the same old problem and when i go in network connections my local area connection says i am connected but it wont let me use the internet. also above when i have been trying to set up the router this "Internet Gateway" pops up in my network connections and it is disabled and whenever i try to enabled it it just says failed.

I'm on Cable broadband my modem is a Motorola SB5101 SURFboard cable modem and the router is an Linksys Cisco e2500 and i am using windows xp sp 3

View 4 Replies View Related

Linksys Wireless Router :: E1500 DHCP Gateway Address Always Defaults To Access

Apr 28, 2012

I have a ADSL Modem with built in router that the E1500 is connected to via Ethernet.If I choose "Automatic Configuration" for the internet connection setting on the E1500 I can enable DHCP on the E1500 but the gateway it gives to clients is always that of itself (192.168.1.1). The gateway it should be is that of the ADSL Modem (192.168. 1. 254).If I choose "Bridge Mode" I can't even enable DHCP.Is there a way I can use the DHCP server?

View 1 Replies View Related

Linksys Wireless Router :: Connecting WRT300N To Uverse Gateway - Dynamic IP Address?

Feb 6, 2012

I have a WRT300n router and want to connect to my Uverse Gateway. When I connect them & try to use the internet connection I get an error that says a connected router must be capable of using DYnamic IP addresses.

View 1 Replies View Related

Amilo Pa1510 Connected But Not Surfing (wrong Gateway IP Address)

Mar 30, 2013

I have an Amilo Pa1510 (Windows XP) and I can connect to the router but not surfing (browser doesnt load any website). I have tried the commands "ping" to my IP address and it works but ping to the default gateway IP address doesnt work either.I am using the same wireless connection right now with my smartphone. I have downloaded an app that executes the ipconfig command in my Android. I have used the same gateway IP address in my laptop but it didnt work either. I have tried to set automatically the IP addresses in my laptop without success too. I have turned off and on both laptop and router and also checked in the system window that all the processes such as DHCP and DNS servers are automatic and enabled.

View 4 Replies View Related

Linksys Cable / DSL :: WAG120N And RV042 - Get IP Address / Browsing Fails

Apr 7, 2011

I have WAG120N & Linksys RV042. I configured the WAG120N encapsulation to "Bridge mode only" and once I connect a pc to one of the RV042 ports, I could access Internet without any problem, but if I connenct a PC to a port on the WAG120N, then I can't get IP address and browsing fails.
 
How can I connect the above 2 devices in order to be able to browse Internet through Ethernet ports of RV042, Ethernet ports (and wireless of course) of WAG120N, and finally configuring this setup to allow QuickVPN client (or site-to-site VPN) to access a an application server on my LAN.
 
My Internet connection is based on PPPOE. How to do the configuration for my setup.

View 1 Replies View Related

Linksys E2500 - After Changing Router's Local IP Address It Becomes Inaccessible

Mar 7, 2013

I'm adding another router to my home network to extend my WiFi range. (Linksys e2500.) I'm trying to change its IP from the default 192.168.1.1 so that it doesn't conflict with my primary (dhcp) router.

To isolate matters I've reset the router to factory settings, turned off my mac's WiFi and then connected the Mac to a Lan port on the router. Now I can view the router's admin page at 192.168.1.1.

Now I change its local IP to 192.168.1.3 and leave the subnet as 255.255.255.0. The router reboots and after several minutes is inaccessible at any IP I try (still hardwired to the Mac with WiFi off). Ifconfig doesn't show the router and the only way I can get it back is to factory reset it again.

View 4 Replies View Related

Linksys Wired Router :: RV042 - Can't See Remote Computers When Connected Via VPN

Feb 10, 2011

I've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2.  I can ping the RV042 and log into the administration page and make changes.  However, I can not see other computers on the remote network.  I can not ping them.  When I open my Network page, I still see the computers on my local network.
 
All machines are running Windows 7 Ultimate.  ISP is Comcast at both locations.  WAN IP's are dynamic, but have not changed in over a year.  Local IP's on the remote (home) network are static..[url]....

View 1 Replies View Related

Linksys Wireless Router :: EA3500 - Change IP Address Of PC Connected?

Jan 12, 2013

I have a PC with Windows 7 connected wirelessly to a EA3500 router. How do I change the IP address on my PC ?

View 6 Replies View Related

Cisco Routers :: RVS4000 - Browsing Remote Network Computers?

Feb 24, 2010

I have recently bought RVS4000 and I'm having problems with remote network computers. I can only access them by IP, by name it always fails. Localy I have BEFSX41, remotely RVS 4000, connected throught VPN. Everything else is working fine.

View 6 Replies View Related

Connected But Internet Is Not Working Linksys E2500?

Jul 7, 2011

I bought I router today, Linksys E2500 and set it up, for some reason its connected with full strength but the internet does not work on my computer, or any other device connected to the network I established on the router. I've looked through so many articles and posts on here, I've fixed the winsock, I tried the netsh winsock and the netsh int ip reset reset.log, but when I put in netsh int ip reset reset.log in the command prompt, nothing happens after I press enter. I've updated through microsoft updates, and updated some drivers from the hp website. Ive repaired, and tried restarting the router, and even the modem and nothing changed. It's still connected, but the interenet still is not working. The modem is fine, as when I disable the wireless connection, the internet works. Yes, I have Sp3 installed. I am using windows xp and the computer is called HP Pavilion a1013w Desktop PC.

Heres my Ipconfig /all while my wireless connection is disabled:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsOwner>IPCONFIG /ALL

[Code].....

View 3 Replies View Related

Set A Printer To Serve 2 Computers Through A SMC Gateway Router?

May 12, 2011

I have a SMC Gateway Router and 2 computers connected to it with RJ-45 cable. They are (1 iMac + 1 PC) 150 feet apart both computers are wired to the router. I also have a Canon Pixma MP 560 Multifunction Inkjet printer that has the capability to be connected both wired and wireless. Right now it is only connected to the iMac via a USB connection as all 3 (router, iMac and printer) are on the same workstation.I would like a detailed explanation as to how to connect the printer so it could also support the 2nd computer a Windows PC which is located on the floor below. Can I do that through the wired router too?If not possible, I also have the capability to connect wirelessly although I would prefer to use the wired connnections.The PC has a Belkin USB 2.0 Network Adapter for wireless connection; both SMC Router and Belkin USB adapter are 902.11 N capable?

View 1 Replies View Related

Linksys Wireless Router :: E4200 Dropping Connection While Browsing?

Jan 2, 2013

I have e4200 router and i notice sometimes when i  am browsing that dops connection.

View 9 Replies View Related

Linksys Cable / DSL :: Wag120n Can't See Other Connected Computers

Jul 1, 2011

I have multiple macs and when all of them are connected to the wag120n router, macs can't seem to find/see each other as if they are connected to different networks. I have tried another router ie. netgear dg834g router and this problem didn't occur and i am able to connect over the network without a problem. Obviously there is something wrong with the router settings.

View 2 Replies View Related

Linksys Wireless Router :: WRT160N Monitor Browsing And Speed Limiting

Aug 28, 2011

I am sharign my bandwidth with my neighbour and would like to keep a tab on what he is downloading, and then limit the speeds he gets while using my 4Mbps line. He's accessign using a WIFI L:AN card.Can I do this usign WRT160Nv2? Maybe any third-party. 

View 2 Replies View Related

Phone Connected To Wifi But Not Browsing

Feb 5, 2011

phone detects wifi asks for code then gets connected.but when i open the browser and start log on it says invalid server name

View 2 Replies View Related

Linksys Wireless Router :: E4200 Browsing And Connecting To Device Closing Window?

Feb 9, 2011

Last week I purchased the E4200 and for simplicity, I configured it with basic settings using Cisco Connect. Today, I went into the web interface. The only thing I did was review settings and get the Routers PIN (it appears that Intel Chipset cards on Windows requires this PIN?)  Close the browser (did not save any settings) and now I am completely locked out of the device. Cannot connect does not accept the wireless password.  I hard reset the device, ran through the wizard. Everything was working again. Launch the browser and connected to the device closing window and balm?

View 9 Replies View Related

Cisco VPN :: Internet Browsing While Connected To ASA5505 AnyConnect

Sep 22, 2011

When remote workers - working say from home connect into the company's LAN via an ASA5505, is it then possiable to then go back out to the internet using the ASA as the gateway to the internet.It works if I point towards an internal proxy server.

View 4 Replies View Related

How To Change IP Address For Browsing

Jun 20, 2012

I'd like to register another account in a forum to comment anonymously so I need a different IP address for browsing.I remember that I had been trying this long time before but it was not easy to make it. Using proxy website is useless because the speed is very very slow. Is there any way to painlessly, easily change IP to browse websites?

View 4 Replies View Related

Linksys Access Point :: E2500 Obtaining IP Address Timing Out While Connecting

Dec 5, 2011

I have a E2500 router and 3 WAP610N access points.  Users are having a difficult time connecting to the AP's.  The client device just sits there trying to obtain an IP and then times out.  If they get within range of the actual wireless router, then connect instantly.  Is there a setting to increase that will allow longer time trying to obtain an IP?
 
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap.  See diagram below.  Not sure if this has some impact?

View 4 Replies View Related

3 Computers Connected To 1 Modem Router?

Jun 2, 2012

There are 3 people in my house that are connecting to the internet by a single modem router, everything is fine when there is only 1 of us online , but when there are 2 or 3 of us online , our download & our upload speed dramatically decreases . So is there a way to maintain our normal download & upload speed even when all 3 of us are online ?

View 10 Replies View Related

Small Network / Random Computers Lose Browsing At Random Times?

Dec 29, 2012

Network running about 60 computers, most of which are running windows 7 professional. Some are on a domain, some are not.At (seemingly) random times, some computer on the network will lose the ability to browse websites (including the web interfaces of networked devices). I can't identify what circumstances cause this to occur. I only find out about it when someone calls me.From the affected computer:I can ping sites I can ping our Cyberoam UTM (which acts as our DNS, DHCP, and firewall)disabling/enabling connection doesn't fix the problem releasing/renewing ip doesn't fix the problem flushing dns doesnt fix the problem uninstalled antivirus on two test machines, problem still randomly manifests.replaced the Cyberoam with newer model users have claimed that if they wait a long period of time (40+ minutes) the problem sometimes resolves.rebooting the computer resolves the issue until it randomly occurs again changing the computer's mac address also resolves the issue until it randomly occurs again.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved