Linksys Wireless Router :: E4200 Browsing And Connecting To Device Closing Window?

Feb 9, 2011

Last week I purchased the E4200 and for simplicity, I configured it with basic settings using Cisco Connect. Today, I went into the web interface. The only thing I did was review settings and get the Routers PIN (it appears that Intel Chipset cards on Windows requires this PIN?)  Close the browser (did not save any settings) and now I am completely locked out of the device. Cannot connect does not accept the wireless password.  I hard reset the device, ran through the wizard. Everything was working again. Launch the browser and connected to the device closing window and balm?

View 9 Replies


ADVERTISEMENT

Linksys Wireless Router :: E4200 Dropping Connection While Browsing?

Jan 2, 2013

I have e4200 router and i notice sometimes when i  am browsing that dops connection.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - Block Popup Window That Displays Every Time In Form / Save Settings?

Mar 23, 2012

I just installed my new E4200, and am setting the Access Restrictions.  Is there anyway to block the popup window that displays every time I enter the form or save the settings?
 
I'm using IE9 and have tried adjusting the Popup Blocker, but to no avail.

View 7 Replies View Related

Linksys Wireless Router :: Droboshare Device Won't Connect To New E4200

Aug 17, 2012

connecting a droboshare device to a linksys router.  The droboshare that I've been using for several years and have A LOT of important files on works well with my old router (sagem) and now on my new e4200 doesn't appear to connect.

View 3 Replies View Related

Linksys Wireless Router :: E4200 V2 - Limit Bandwidth On Particular Device?

Jul 6, 2012

I want to know how I can manually limit the Kbps for a particular devince in the QOS.I DO NOT want to simply set the priority (low/med/high). I want to "physically" limit a device.
 
When I select to do it manually (upstream bandwidth) it limits ALL devices and I do not want this. I want to limit the bandwidth on only one device that is connected (ie an Xbox)
 
I have a Linksys E4200 V2

View 9 Replies View Related

Linksys Wireless Router :: E4200 File Timestamp On USB Attached Device?

Apr 26, 2011

I've verified that the router and the pc have the same time zone, daylight savings update specification and that they both showed the same time (00:56AM).  But a file created on the attached USB device was timestamped 01:56AM (the date was correct). 

View 9 Replies View Related

Linksys Wireless Router :: E4200 Non-supported Device Is Connected To USB Port

Dec 16, 2011

I'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router.  I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware.  I get the message "A non-supported device is connected to your router's USB port.  Disconnect that device and follow the steps below to connect a USB printer to your router."  Cisco support was not beneficial. 

View 1 Replies View Related

Linksys Wireless Router :: E4200 - Use WPA2 AES Security In Conjunction With Media Device

Jan 24, 2012

I am trying to change the security on my router so I can use WPA2 AES security in conjunction with a media device. The router security page only gives me a choice of WPA2 Personal or WPA2 Enterprise (which requires the use of a Radius Server that I don't have). 

View 1 Replies View Related

Linksys Wireless Router :: E4200 Windows 7 Not Connecting

Feb 20, 2012

I've had for several years very good experience with the WRT54GL. Based on that experience I upgraded to a e4200.But so far it's not living up to my expectations (media server not probably working with external harddisk, no advanced logging of incoming/outgoing traffic, connection problems) and I'm getting pretty frustrated with it.Problem right now is that one of my laptops with Windows 7 is often not connecting correctly to the wireless network of the e4200. It's giving a "unidentified network" error. Rebooting computer and router is not working. The computer is (always) reliable connecting to another wireless network in my home. It seems the DHCP is not working properly?

View 1 Replies View Related

Linksys Wireless Router :: Connecting USB Printer To E4200?

Apr 11, 2011

I think I have worked out that you can`t currently connect a usb printer to the usb port on the e4200 in order to share it over the network. 
 
However I have heard reports that this might facility might be enabled in the spring.
 
I have also heard something about `virtual usb` but I don`t know whether this has anything to do with it.

View 9 Replies View Related

Linksys Wireless Router :: Connecting Switch To E4200?

Nov 24, 2012

Have a Linksys E4200 router located in my basement and I am experiencing a puzzling wired connectivity issue as follows:  Port 1 on the router is for my study, I have no problem getting connection regardless  if I use my study's Ethernet jack or if I run a 5 ft. cable (hereinafter THE CABLE) from the router’s  port 1 to my laptop (i.e., cabling does not make a difference).I then connect to router port 1 an EZXS55W Linksys switch (using port 1 on the switch and THE CABLE) and then connect my laptop to port 2 on the switch using a second cable.  I am unable to connect to the network/internet even after rebooting both the cable modem and router.I then reconnect my study to port 1 on the router, I go to my study and connect the study’s Ethernet  jack using THE CABLE to port 1 on the switch and using a second cable from port 2 on the switch to my laptop. …. I get an network/internet connection immediately !  FYI, I have had the exact problem with switches EZXS88W and SE2500 (no longer own this).

View 5 Replies View Related

Linksys Wireless Router :: E4200 Can't See Anything On Server After Connecting

Aug 23, 2011

I've been messing around with this for several weeks to no avail.  I've never had a problem establishing a VPN connection within my LAN.  I've tried several workarounds, learning things in the processs, but to no avail.I've set up a VPN connection with Windows 7.  The RRAS server is at home and I'm attempting to access from school (or the internet anywhere).I have no problem establishing the VPN connection (that I can see).  Port 1723 is forwarded for both UDP and TCP to a static LAN address (198.162.1.124) in the E4200.  PPTP pass-through is enabled (as well as the other two options).I can't see anything on the server after connecting.  I'm using a DDNS.  It works just fine INSIDE the LAN; I've even mapped a network drive to "S:".  Accessing ANYTHING outside of the LAN over a VPN, however, isn't working. [code]

View 9 Replies View Related

Linksys Wireless Router :: E4200 Media Server Becomes Unavailable Most Of Time / Renders Device Useless

Feb 6, 2011

I have the new E4200 with an attached 750GB hard disk.All works well, however the media server becomes unavailable most of the time and renders the device useless.
 
I can connect to the Media Server from my xbox and laptop for an hour or so, and then all of a sudden it is gone. The only option I have is to reboot the router to bring it back online however not all of the music and videos are shown on the media server (yet).I uploaded quite a bit of music and video to the hard disk, I can initiate a scan but after a while the media server becomes unavailable / cannot connect to it.

View 9 Replies View Related

Linksys Wireless Router :: Ea4500 - One Device Not Connecting To Wifi Network

Feb 3, 2013

I just purchased a Linksys EA 4500.I set up the wifi properly, with laptops, tablets, smartphones and printer. The wifi network worked fine for a couple of days.But now one of the laptop "refuses" to see the Linksys wifi network. The other devices are still connected and running regularly.
 
The notebook that does not connect anymore is an ACER 5740DG with an Atheros Network adapter and Windows 7 installed. This notebook is otherwise running fine.At the beginning it was connecting ok and we never had any problem at all with the previous router Belkin_N+_7991AC, that I changed just for speed.
 
Now the Linksys network is simply not visible to such notebook in the "Available Connections List" that I get clicking on the WiFi icon in the bottom right, while a number of other wifi networks (not mine) are clearly visible. Of course I restarted the notebook properly. For one time I got the visibility of the Linksys, I entered the password and then it was not possible to see the network anymore.No error message from Smart WiFi software.

View 5 Replies View Related

Linksys Wireless Router :: E4200 - Connecting 2 Android Phones?

Aug 19, 2011

I have an issue with a brand new E4200 router. My E4200 can connect no issue with the following devices: Ipad, AppleTV, Dell Laptop, Ibm Laptop. It is also wired connected to my home PC. Internet works fine and file sharing/network works good for all the above devices.
 
The problem is that My wife and I's Phone can not detect the wifi network and can not connect to it. The SSID broadcast is enabled on both frequencies (2.4 and 5). I have try configuring the network manually on both the Android phones..it does not work.. it records the data but keep sayng the network is out of range (although I'm right next to the router).  I hva eplayed with various channels on both frequecies and played also with the MTU size.One of the Android phone is Garmin the other Acer Liquid...different brand running both Android 2.2...
 
Firmware on E4200 is 1.0.02
All settings reset to Auto/MIxed for now.
WPA2 is enable with security key
SSID is enabled on both frequency
no MAC address filtering is setup
 
Both my phones can detect other networks and can connect fine to friends and family networks...So I suspect a compatibility problem between router an Android..I have contacted Linksys support twice with no avail. I have contacted both Acer and Garmin...they refer me to linksys

View 1 Replies View Related

Linksys Wireless Router :: E4200 Not Connecting With Cradlepoint CBR450?

Sep 22, 2011

I am trying to replace my Cradlepoint MBR1200 with a CBR450 in bridge mode, to let the E4200 take over all the WAP and DHCP handling, but having a hard time.I set the CBR450 in bridge mode and when I connect it to my laptop it properly passes the IP info to my Mac and allows me to connect.  I then connect it to the E4200 WAN port with it set to get IP address automatically but nothing ever happens and I am never allowed traffic in/out over the WAN.
 
I *can* get internet access by leaving the CBR450 in normal mode (handling DHCP, etc) and then plugging it into the E4200 LAN port and having the E4200 set to bridge.why the E4200 WAN port is not getting the bridge info and allowing connection?  FWIW, works fine connecting to a DSL modem with the DSL model set to bridge mode at my other house.  
 
CBR450 and E4200 both on latest firmwares.

View 2 Replies View Related

Linksys Wireless Router :: E4200 Gigabit Ports Connecting To PC And NAS

Jan 19, 2012

Have the issue of connecting a pc an NAS to a E4200 and when transferring from pc to NAS, only getting < 10 mbps transfer rates? NAS is Dlink 321. PC has Gigabit ethernet card. cables are cat 6. Even when I force the NAS and pc network card speeds to 1.0 GBps full duplex, I only transfer files at < 10 Mbps.

View 3 Replies View Related

Linksys Wireless Router :: Connecting Wag320n To E4200 Via Wifi Bridge

Dec 6, 2011

I purchased a WAG320N and E4200 and have manged to get the modem connected to the internet and it's running fine in that respect, with no adjusting done to the settings.My intentions are to connect the WAG320N to the E4200 wirelessly, as they are in seperate rooms in the house and have done a similar setup in the past with a 7300G Billion Modem and WRT54GL. 
 
With the E4200 I quickly discovered there was no bridge mode out of the box, but checking these forums got the indication that the firmware updates added this capability, so updated it..I entered the IP Address of the Router, the Subnet mask of the network and the Default Gateway / Modem router IP address into the fields, following this guide, but have not been able to get the computers to contact one another, nor ping the other devices. 

View 1 Replies View Related

Linksys Wireless Router :: IPad Not Connecting To Cisco Connect Using E4200?

Aug 27, 2011

I have an E4200 wireless router which is connected via USB to my Canon MX 308 printer. I am able to print from Windows computers that are connected to this router (via WiFi of course). My iPad 2.0 is able to connect to the internet via the router. However I am not able to print content from my iPad via the E4200 router (via Wifi using Cisco Connect software).

View 1 Replies View Related

Linksys Wireless Router :: Connecting D-Link 930L Camera With E4200

Sep 17, 2012

I'm trying to connect the D-Link 930L Wireless N Camera to my E4200 router. When I have the camera connected via the Ethernet cable it works fine, as soon as I unplug the Ethernet cable it will not connect wirelessly. I tested the camera on a friends router E3000 and the camera connects fine and work flawlessly on his network wirelessly. Any settings in the router that need to changed or set differently?? All of my other devices work great. I have been through D-Links Tech support all things point back to my router.

View 6 Replies View Related

Linksys Wireless Router :: E4200 And Slingbox Firmware Not Connecting / Playing

Dec 9, 2011

I have a new E4200 with the latest firmware and my slingbox seems to not be playing nice with the router.  It refuses to take the IP I reserved for the SB, but always defaults to 192.168.2.254.  I use a 2 subnet just in case you're wondering.  I have tried multiple reboots and the IP does not change.  I have tried turning off UPNP, figuring that was hijacking the dhcp server, but that hasn't changed anything. I also notice that a few of my connected devices do not show up in the dhcp list, yet they connect and work ok. 

View 2 Replies View Related

Linksys Wireless Router :: E4200 Devices Weren't Connecting To Internet

Jan 4, 2013

I was attempting to use my EA4200 in bridge mode but found out for some reason my devices weren't connecting to the internet. So I decided to try to access the router through the IP address of the router with no avail.  So I pull the router and plug it in normally and notice that it keeps flashing. So that already gives me an idea something is wrong. I go through the process of unplugging everything from the router, and plugging my PC directly into the LAN port 1 of the router then powering it up. On my network connection list it keeps trying to identify the network but keeps failing (keep in mind that the router still is flashing). So I decide to attempt a 10 second reset, then a 30 second, then a 30-30-30. All with no success. The router keeps flashing. 
 
Which gets me to the point where I am now... router flashing at me, and wondering if this now out of warrenty unit was a waste of money. I am noticing that a lot of people have had questions and issues with the E4200v2 which now concerns me, well hopefully this can be fixed. 

View 9 Replies View Related

Connecting Router Equals No Internet Browsing

Jan 1, 2013

Every time I connect my router, I can't use the internet browsers. But I can see there's a internet connection. Bu once in a while even with just a modem connected to my computer I can't use the browsers. The signal from the router to my Xbox 360 works but sometimes it says there's DNS Error or IP Address Error causing my Nat to be strict. Once in a while, I can access my router's page when it's connected. [code]

View 19 Replies View Related

Cisco :: LMS 4.0.1 - Device Status Window Does Not Complete Load

Jan 18, 2012

i have newly installed lms 4.0.1 server, where i get the "device status window" in the troubleshooting section not loaded.most of the items on the page are loading...., but they will never get loaded completely.i have checked all updates and bugfixes for lms and also for solaris.in the daemons.log file i found the following error messages, they are repeated every few minutes:
 
In EPMOgsAdapter:EPMOgsadapter is sleeping. Waiting for OGSServer to come up com.cisco.nm.xms.ctm.common.CTMException: URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
17/Jan/2012 12:06:55:307 ERROR  ? ?  - URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
17/Jan/2012 12:06:55:320 ERROR  ? ?  - URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
17/Jan/2012 12:06:55:321 ERROR  ? ?  - URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!

[code]....

View 5 Replies View Related

Linksys Wireless Router :: Wtr310 Window 7 Gives Connection Error 651

Dec 10, 2012

I have DSL with a Westell 6200 modem configured to a Linksys wtr310N router. I configured "Bridge Mode" on the modem and configured the Linksys with PPPoE. When I try to log in with my laptop running XP I am connected and everything works great. I also can connect wired to my Windows 7 laptop but I can't connect using wireless. Are there any tricks to make this work on Windows 7? Do I have to set up a new Broadband connection? How does my laptop connect to my linksys router?

View 5 Replies View Related

Linksys Wireless Adapters :: WUSB300N Not Connecting With E4200

Feb 17, 2012

i purchased an E4200 router to replace my old WRT150N. I had a WUSB300N that connected fine to the old router, but it's not connecting to the E4200. I have a guest network set up on it, and the adapter can connect to that, so I'm at a loss as for why it won't connect. Does anyone think it has something to do with the type of security I have set up? I had it on WPA2 on my WRT150N, and the E4200 on WPA2/WPA mixed mode.

View 2 Replies View Related

Linksys Wireless Router :: EA6500 Devices Not Appearing In Network Window?

Jan 31, 2013

We purchased an EA6500 to take the place of the router function of a Verizon Westell 7500.  We bridged the Westell, installed and set up the EA6500 and everything seems fine.
 
What is strange is that some devices on the network (our server, user PC, a NAS that isn't part of the domain) while accessible if you navigate to them via \ do not appear in the Network window.
 
This of course is causing issues for some users who don't or won't map network drives.
 
At first I thought this may be an issue related to us having some of our network devices with static IP addresses so we switched them over to dynamic - no change in the network window.
 
we will have to return this router and get a different brand/model if it won't work in this fashion.

View 9 Replies View Related

Connecting Window 7 With XP With LAN Cable

Mar 26, 2012

How can i connect my window xp with window 7? "I have already done all settings like workgroup setting, ip location but my window 7 lappi is again showing yellow point."

View 2 Replies View Related

Linksys Wireless Router :: WRT160N Monitor Browsing And Speed Limiting

Aug 28, 2011

I am sharign my bandwidth with my neighbour and would like to keep a tab on what he is downloading, and then limit the speeds he gets while using my 4Mbps line. He's accessign using a WIFI L:AN card.Can I do this usign WRT160Nv2? Maybe any third-party. 

View 2 Replies View Related

Connecting USB Internet Device Directly To Wireless Router

Aug 9, 2012

I want to buy a wireless router to which I can connect my USB internet device directly, so I don't have to turn on my PC all the time if I just want to use my moble phone or iPOD or other family members wanting to connect to internet.

View 1 Replies View Related

Linksys Wireless Router :: Cisco E2500 - Using Gateway Address As Browsing IP For Connected Computers

Jan 31, 2013

Everything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access.  We have a statis IP assigned by our ISP solely for this purpose.  For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing.  When we hard line into the modem, we are able to browse it fine.  When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it.  We had set it up about a year ago, and i completely forgot how. 

View 2 Replies View Related

Uverse Wireless Router - Laptop Not Connecting Internet With New Device

Apr 4, 2011

I have a compaq laptop running Vista. We recently had our Uverse wireless router/modem replaced. Now my laptop will not connect to the internet. The laptop connects to the router but shows up as local connection only. Uverse tried all kinds of differant things to no avail. The laptop will hookup with a USB modem but I would like to get it back to how it was before.

View 14 Replies View Related

DLink Router - Connecting Wireless Device To Hardwired Network?

Feb 7, 2011

I have just purchased a new ASUS Laptop for my wife.We are currently running two destop computers on a D LinK Router. How do I go about including the new computer on the network wirelessly?What do I need to purchase to make the transition easiest? The two desktops are running Windows XP Professional, the new system is Windows 7.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved