I want to buy a wireless router to which I can connect my USB internet device directly, so I don't have to turn on my PC all the time if I just want to use my moble phone or iPOD or other family members wanting to connect to internet.
View 1 RepliesI have a compaq laptop running Vista. We recently had our Uverse wireless router/modem replaced. Now my laptop will not connect to the internet. The laptop connects to the router but shows up as local connection only. Uverse tried all kinds of differant things to no avail. The laptop will hookup with a USB modem but I would like to get it back to how it was before.
View 14 Replies View RelatedI just want to connect two computers over the internet as if they are in the same network. This doesnt have to be VPN I dont care about security I just want to get them connected as if they are on the same network. Is there anyway to set this up in my linksys router? Can I use windows VPN? What is the easiest way to get this accomplished? Can you somehow connect two routers through internet like one is 192.168.1.1 and one is 192.168.2.1?Like I said I dont really care how it is done I just need it done. Any easiest way to connect two computers through internet so that they are on the same network.
View 11 Replies View RelatedI I use a Linksys E3000 router. Sometimes when I look at the network map I see a device called "Unknown." It appears as though the two notebooks sometime are going through this device to access the Linksys E3000. (I've checked when both notebooks are on and I can determine what devices are connecting directly to the router and what devices are going through this unknown device.) Is there any way to determine what this unknown device is?
View 5 Replies View RelatedI have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
I have just purchased a new ASUS Laptop for my wife.We are currently running two destop computers on a D LinK Router. How do I go about including the new computer on the network wirelessly?What do I need to purchase to make the transition easiest? The two desktops are running Windows XP Professional, the new system is Windows 7.
View 4 Replies View RelatedI just purchased a Linksys EA 4500.I set up the wifi properly, with laptops, tablets, smartphones and printer. The wifi network worked fine for a couple of days.But now one of the laptop "refuses" to see the Linksys wifi network. The other devices are still connected and running regularly.
The notebook that does not connect anymore is an ACER 5740DG with an Atheros Network adapter and Windows 7 installed. This notebook is otherwise running fine.At the beginning it was connecting ok and we never had any problem at all with the previous router Belkin_N+_7991AC, that I changed just for speed.
Now the Linksys network is simply not visible to such notebook in the "Available Connections List" that I get clicking on the WiFi icon in the bottom right, while a number of other wifi networks (not mine) are clearly visible. Of course I restarted the notebook properly. For one time I got the visibility of the Linksys, I entered the password and then it was not possible to see the network anymore.No error message from Smart WiFi software.
Last week I purchased the E4200 and for simplicity, I configured it with basic settings using Cisco Connect. Today, I went into the web interface. The only thing I did was review settings and get the Routers PIN (it appears that Intel Chipset cards on Windows requires this PIN?) Close the browser (did not save any settings) and now I am completely locked out of the device. Cannot connect does not accept the wireless password. I hard reset the device, ran through the wizard. Everything was working again. Launch the browser and connected to the device closing window and balm?
View 9 Replies View RelatedWhat I learned was it was bad to connect directly to the modem because you are left open to the internet. Currently my friend just got the internet and I told them to buy a router but they did not, and just have it directly connected to the modem. Is this fine, because they only have one computer, and it works fine for now, but wouldn't this be prone for attack?
View 3 Replies View RelatedI've been trying to connect my laptop directly to my Arris modem with an ethernet cable to get on the internet, but for some reason every time I do I have "limited access" and can't get on the internet. I can only seem to get my laptop on the internet while the wireless router is connected to the modem and then either connecting wirelessly or by connecting my laptop to the wireless router with an ethernet cable.I want to connect to the internet without my wireless router, because someone was hacking our router and was apparently doing illegal downloads. We got a cease and desist letter that said our internet will be terminated if it happens again, so I want to connect to the internet without any wireless connections being set up.
View 3 Replies View RelatedI have a problem, my netbook eMD355 is not connecting directly to our wifi. I tried to restore the system but still it doesn't connect. My windows here is WINDOWS 7 ultimate.
View 1 Replies View RelatedI've got VPN connection from Cisco 877 to ASA 5520 and on the Cisco 877 I've got SIP device which doesn't has to go through VPN. I assume that for the best audio quality I should bypass the VPN and connect directly to the SIP servers, but how to configure it??
View 3 Replies View RelatedIs this a good idea to connect access layer directly to core layer with fiber and omit the distribution layer?
View 2 Replies View RelatedI would like my dcs-930l ip camera to be directly connected to my d-link dsl-321b modem (which has only one rj45 port to connect to), so that I can either access the cam via the internet (watching livestream through webinterface, that would be option 1) or so that the cam sends an email with a picture as soon as the motion sensors activate - that would be option 2 (by the way: the modem / cam get internet access through german telekom / t-online).
I have tried to get option 1 as well as option 2 to work, but I failed... I would be happy if either option 1 or 2 would work for me - I don't really care which one. In both cases, the problem seems to be that the dcs-930l cam cannot access the internet (but the cam itself works - I can view the livestream through the local network).
So I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
View 1 Replies View RelatedI cannot connect to the internet via my router. The router is functioning properly two other computers in the house use the router one though Ethernet cable and the other one connects wireless. Things I have done while trying to figure out the problemMade sure all windows updates were up to date Scanned for viruses and malware (none were found) Uninstall the network adapter Made sure the network adapter driver were up to date
I have noticed that when I plug the Ethernet cable from the router to the computer the led on the back of the computer panel does not blink as it does when I route directly from he cable modem.
I want to know is it possible to check Internet speed directly in the cisco router thru any command or activating any service in the cisco router?.As it is seen most of the times internet speed offer by ISP is different as compared to clients.and Clients most oftenly not satisfied with internet speed The problem is that our ISP has given us 100MB leaased line.But when we deployed in production network the speed is same as DSL.We have reported this issue to ISP they then carried out Iperf test by connecting laptop directly with the ISP router.They have tested the speed and it shows about 94-96 Mbps and argu that it is up to the mark and there is problem at your side(i.e our internal network).Now our internal network has cisco 1841 router connected directly to ISP 3825 cisco router.Our router has minimum configuration as required to pass traffic out and in.Our internal 1841 router is connected to switch to which different clients are connected.We have performed some online tests using different speed checking websites and also perform real time tests by uploading and downloading files.The speed is much low as compared to 100Mbps and it is nearly or slightly higher then as DSL connection. how can we check internet speed in the specified scenario?Is there any command or service available in cisco router to check internet speed as we want to check ISP connection speed directly thru 1841 router?what about authenticity of online speed checking websites?Any specialize software/tool you recommend to check Internet speed in specified scenario?
View 11 Replies View RelatedHow do i stop a Wireless device from connecting to the router? i attempted to find an answer myself and failed
View 1 Replies View RelatedI have full signal strength but I can't connect to the internet from any device. Internet works fine when connected directly to devices. Devices will show an IP address but will not connect to the internet. The first router worked fine for about a year and did the same thing so I replaced it but now after 1 month, this router is doing the same thing!
View 1 Replies View RelatedMy WRT310N linksys wireless router has recently stopped permitting internet access to devices connected to it, both wired and wirelessly. I have connected my broadband modem directly to a single computer (which is how I am posting this) and evidently there is nothing wrong with my internet service. I have tried restarting my modem, the router, and the computers I am trying to access the internet with, and it has not worked. Note that local communications work fine, I was able to ping another device connected to the router, and even establish a TCP connection.It is possible that the settings on the router have been changed without my knowledge, if so, however, I do not know which setting could be causing this.
View 1 Replies View RelatedMy question is how can I use this existing wi-fi as input to a router to make a sub wi-fi for four computers and a wireless printer. Some of my computers may need to be wired into the router.
View 5 Replies View RelatedMy desktop gateway computer slowly started having problems connecting to the internet via the hard ethernet connection to the router(Netgear). Wireless devices connected OK (although often slow). I assumed it was the router so I bought a new one (Linksys), but it's having the same problem. New router I can connect to with my laptop but not with the desktop. Latest errors during setup are Local Area Connection does not have a valid IP configuration and the default gate way is not available.
I restore to factory defaults? I'm running Windows 7 Home Premium on the desktop.
I was giving a RHO 7" notebookbook that was bought in korea, but I can,t seem to get it to connect to the internet, i have a wireless router from att that i use on my toshiba laptop and other devices such as psp and i don't have a problem connecting them although the wireless signal is being picked up i can't seem to connect with the notebook
View 1 Replies View RelatedI have a very annoying problem with my Linksys WRT54G2.When I connect a wireless device (laptop, phone, TV, Ipad) to my wireless network I only see a Local connection, no connection to internet. After resetting the router (power off for several seconds) the internet-connection is available again.I have to do this every 1 - 2 days.
View 7 Replies View RelatedI've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
I have a Netgear WNDR3700v2 that I was very happy with until I got a nest thermostat. Apparently it is an unsupported router and I had to change it. I bought a E2700 since it was supported, but I'm having a huge dilemma...
If I connect the linksys directly to the modem, I'm not getting an internet connection. I've released and renewed IPs to no avail..
but if I hardwire the linksys to the netgear, I do get a good solid internet connection. problem is, I have no need for 2 routers setup on top of each other.
basically, I dont understand why linksys is not able to connect directly to the modem. yet it gets solid connection hardwired through another router.
I'm using Comcast and in south FL. it's a motorola surfboard modem
I recently purchased the router and got the CCC firmware on. It works fine for a while but then I can't connect to the router using my PC unless I log using the remote credentials. Generally if this were the case I wouldn't care but when I do it that way I can't run the speed test. After I reboot the router it works fine again, for a while.
For some reason, it doesn't detect my PC as being connected directly although my PC is connected by wire, directly to the router.
I wanted to connect to the internet so plugged the same cable into my laptop (running 7) [code]...
View 3 Replies View RelatedI think our brand new Belkin router toasted itself after it automatically updated it's firmware. We've had it for three days the first two days we were downloading around 2MB/s, then last night it updated itself and since then it's been crawling around 100kb/s.
I've tried to plug the desktop right into the modem to see if it'd speed back up but it won't give it internet access this way. I've tried rebooting the modem after and before switching cables around but nothing will make it change.
We have a DIR 655 router that I have set up with LAN and WiFi, all good.Today we received our mast and antenna from Vodacom (ISP) with the Public IP's to enter into the router. We connected the LAN cable into the Internet Port and did a manual Internet Static IP setup. But as soon as we click save it says: Type is not for 3G... How do I go about entering the public (static) IP's we received from the ISP in order to get the Internet operational?
View 8 Replies View Relatedi have an old Netgear MR 314 router that works like a charm for my wired connections, but whenever i try to connect wirelessly from my phone or laptop, it connects but doesn't access the internet.
View 5 Replies View RelatedMy laptop will not connect to the internet. We are using a wireless router and have never had a problem before, it works if you plug the ethernet into it but otherwise it says no network available.
View 4 Replies View RelatedI recently acquired an E4200 Linksys router.Is it possible to connect to it using telnet (from LAN)? For example I would like to start a ping command directly from the router.I tried to telnet using command line shell from Windows and it failed to connect on port 23.
View 4 Replies View Related