Computer Does Not Connect To Internet Through Router Only Directly Through Cable Mode
Jul 18, 2011
I cannot connect to the internet via my router. The router is functioning properly two other computers in the house use the router one though Ethernet cable and the other one connects wireless. Things I have done while trying to figure out the problemMade sure all windows updates were up to date Scanned for viruses and malware (none were found) Uninstall the network adapter Made sure the network adapter driver were up to date
I have noticed that when I plug the Ethernet cable from the router to the computer the led on the back of the computer panel does not blink as it does when I route directly from he cable modem.
somehow connecting my PC to my home network as if it was wired. Having a wired connection just won't work because my PC is far away from my modem and router. The reason I want to connect it wired is because I am getting terrible speeds, and the slowest. [URL]
So I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
I have a Thompson 784 router that connects to the Internet. It works nicely enough.What is wrong is that I have a shielded Cat 5e cable that goes from my room to the router that's in a another room (~30 metres). Both ends are the same; both ends are done nicely; I've tested it with a cable tester and every wire connects. However, when i connect my computer to my router neither one will find the other.
My desktop gateway computer slowly started having problems connecting to the internet via the hard ethernet connection to the router(Netgear). Wireless devices connected OK (although often slow). I assumed it was the router so I bought a new one (Linksys), but it's having the same problem. New router I can connect to with my laptop but not with the desktop. Latest errors during setup are Local Area Connection does not have a valid IP configuration and the default gate way is not available.
I restore to factory defaults? I'm running Windows 7 Home Premium on the desktop.
We have a DIR 655 router that I have set up with LAN and WiFi, all good.Today we received our mast and antenna from Vodacom (ISP) with the Public IP's to enter into the router. We connected the LAN cable into the Internet Port and did a manual Internet Static IP setup. But as soon as we click save it says: Type is not for 3G... How do I go about entering the public (static) IP's we received from the ISP in order to get the Internet operational?
My computer came with Mcaffe pre installed on the laptop however did not stop me getting the police e crime unit virus about three weeks ago. To fix this I booted in safe mode and did a system restore to around 3 months before I got the virus. I then installed avast antivirus and did a scan and boot scan which came back with nothing which suggested to me it had gone. This then meant I had both mcaffe and and avast running at the same time. Then until 3 weeks later the internet suddenly stopped working whilst I was on the internet. My laptop sees my router and says it is connected to it but says the router is not connected to the internet. This is false as every other device in the house can connect. However I then tried my computer in safe mode with networking and it can connect to the internet.
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
I have created users and given them telnet access to router 7200. They have full privilges(15) but everytime they login they login into user-exec mode instead of privilege mode. Is there a way to skip user-exec mode and allow the users to login directly into privilge mode so they dont have to enter password twice?
Just finished building my new computer yesterday - i installed windows 7 and all the motherboard drivers etc - everything went smoothly. I then plugged in my ethernet cable but saw that in normal mode my computer had very slow internet. I went into safe mode with networking and tried the internet there and it was its normal speed. Obviously something is booting up in normal mode that is stopping/limiting the connection. I uninstalled norton (came with the motherboard drivers) using the uninstall norton tool, i also uninstalled any other virus protection and disabled my computers firewall but to no avail - it's still real slow.
I just got new roommates and the internet on his computer would only load facebook and google. NOTHING else. It said he has internet connection but it still wouldn't work. I even called my internet provider and they couldn't figure it out. His internet worked perfectly fine when it was on safe mode with networking. I even disabled his firewalls and I ran malewarebytes but found nothing. I thought this was just his computer but then a day later my computer is doing the same thing! my computer has worked perfectly fine for over a year on the same router and everything but now it has the same exact symptoms as his. I don't know if this is a router issue or not. .
It is a wireless connection, internet provider is cable one, and my router/modem is a Zoom DOCSIS 3.0 cable modem/Router with wireless -N
different ways to connect a printer to the X3000. how to connect a printer to the X3000, i.e. wirelessly, USB port, or directly via one of the LAN ports. I also checked the product information for X3000 on the CISCO website and it only makes reference of the USB port as StorageLink.
. Since then I have reconsidered and now am looking to purchase the E4200V2 to connect in bridge mode to my X3000 instead of the E1500. Correct me if I am wrong but connecting the E4200V2 to my X3000 should be the same connecting the E1500 to my X3000, i.e. bridge mode? Yes or No?And my final set of questions is rregarding what would be the best set-up for adding a storage device and printer to my network once I get the E4200V2 and set it up in bridge mode?
- Should I connect both the printer and storage device to my the E4200V2?
- Should I connect them both to my X3000, which provides my internet connection?
- Should I connect one to the X3000 and one to the E4200, if so which to which for best set-up?
My question is how can I use this existing wi-fi as input to a router to make a sub wi-fi for four computers and a wireless printer. Some of my computers may need to be wired into the router.
I Just switched from DSL to Charter Communications Cable internet. For some reason my computer wont see the internet. I plug the same cord into my brothers computer and the internet works just fine. I plug the same cord back into the DSL and i have internet. I have done troubleshooting and it finds this problem (Your computer appears to be correctly configured, but the device or resource (DNS server) is not responding. I switched to a different cable modem same exact situation. Works on my brothers but not mine. My computer is a much newer and more capable computer then his. When we activated the internet we did it on his computer, but before we switched to charter i plugged the modem in without internet and it seemed to have the same problem. I just got more results on his as it immediately directed my to the charter page at that time. On mine i got nothing. ( Also i believe my brother said that it did work on my computer for a few minutes at first but i'm not 100% on that.)
I have two computers and a laptop. How can I pick up the internet using one router? They are in separate rooms. I done it b4, but was done by someone else, who's not here. I don't remember how she done it, and I'm having a problem
Heres my set-up. In my office building, there's a computer company that gets bundled T1 lines and sends them out to the offices and we pay them. So, in my office i have a jack with a cat5e cable that goes to my router. The issue is that the router's internet light won't turn on.We're on our third router and second brand so I'm pretty sure the router's aren't the problem. If i connect my computer to the same cat5 cable I get the internet without an issue. But, when i put my router in there, it gets nothing. Not even a yellow light.
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
I have a Netgear WNDR3700v2 that I was very happy with until I got a nest thermostat. Apparently it is an unsupported router and I had to change it. I bought a E2700 since it was supported, but I'm having a huge dilemma...
If I connect the linksys directly to the modem, I'm not getting an internet connection. I've released and renewed IPs to no avail..
but if I hardwire the linksys to the netgear, I do get a good solid internet connection. problem is, I have no need for 2 routers setup on top of each other.
basically, I dont understand why linksys is not able to connect directly to the modem. yet it gets solid connection hardwired through another router.
I'm using Comcast and in south FL. it's a motorola surfboard modem
I recently purchased the router and got the CCC firmware on. It works fine for a while but then I can't connect to the router using my PC unless I log using the remote credentials. Generally if this were the case I wouldn't care but when I do it that way I can't run the speed test. After I reboot the router it works fine again, for a while.
For some reason, it doesn't detect my PC as being connected directly although my PC is connected by wire, directly to the router.
I want to buy a wireless router to which I can connect my USB internet device directly, so I don't have to turn on my PC all the time if I just want to use my moble phone or iPOD or other family members wanting to connect to internet.
I want to connect a Netgear FS605 directly to my ADSL router.However I find that this does not work unless I put my Netgear EN2005 Hub in between the Switch and the Router.The Hub is 10Mb/sec the switch 100Mb/s so I would like to eliminate the hub.
I have external hard drive connected to E3000. It is formatted as NTFS and working fine. However if I disconnect from router and connect to PC usb port directly, I get a message that hard drive needs to be formatted.
I have a new router (ASUS RT-N10)and It is asking me to direct connect my cable modem to my computer, and then find my MAC address via command prompt, and clone it to the new router.I can get to my command prompt, the problem lies in windows 7 and vista's (or mine) inability to realize that my network card is directly connecting to the modem. (No internet connection available, doesn't think anything is connected). I have tried on multiple machines to try and find my modem's mac address but it simply is not working.I want to know if I can find the mac address through the old router, or what I need to do to have windows 7 recognize I'm directly connecting the modem to the PC.
I have laptop or desktop both computers and i want to share my desktop matter in my laptop or laptop matter in my desktop without using any modem by the using of a simple cores cable? how i can handle it..
aptop ,i just buy wireless netgear router for wireless net range but it does not work .its saw me the router acess point but some how my internet not connecting . its connecting with linsys but not with my router. its something which i can do ? am thinking of security system on the netgear properties
I migrated my internet from PPPOE to DHCP. My wifi is working with no problem but when I hook up my computer to 1 of the 4 Lan ports I can't seem to connect to the internet I can however log in my router no problem. But I don't get internet access... I wonder what could be the problem. I tried resetting my router and modem to see if just a bug or something but to no avail.
I have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
