I want to connect a Netgear FS605 directly to my ADSL router.However I find that this does not work unless I put my Netgear EN2005 Hub in between the Switch and the Router.The Hub is 10Mb/sec the switch 100Mb/s so I would like to eliminate the hub.
View 3 RepliesNetgear FS605 v3 wont connect to both my ps3 and my pc. It can only get internet to either my pc or my ps3.
View 1 Replies View RelatedI use a Netgear FS605 Ethernet Switch to connect a wifi modem to my network and thus to the internet. People in that room can jump online via the wifi modem. You can also print to the wireless printer in that room via that wifi modem being local. However, I can no longer print to the wifi printer from anywhere else in my network (I could before I got a new router and wifi modem in there).Would this be a problem with this Switch or with the modem e.g.
View 1 Replies View RelatedCurrently, I have 2 Apple Airport Extremes, and 1 Wireless Netgear ADSL Router. The 2 AAEs are connected separately to the router, and this allows us to get coverage in most part of the house (it's a large house with concrete and granite walls). I also have a HP Officejet 8500 'wireless printer' that is wired to the router as you can only print to the printer when it's in standby with a physical connection to the router (that's a different story). So my goal is to replace everything as the router is slowly dying and as a result of this, I want to be able to access the Internet wirelessly throughout the house, and be able to print from any where in the house without anything connected via cables. And as a bonus, I would like the Internet to be accessible 100 yards/metres down the garden (workshop is there). Basically, blanket coverage!
View 3 Replies View RelatedI'll try and keep this brief, we were having problems with our netgear router (DGN1000) mainly with connection when online gaming with PS3, generally poor connection - so purchased a TP-Link router (TD-W8960N). We could usually access the netgear wirelessly on our laptops Dell and Acer Aspire 4820T (both Windows 7) without any problems and were still doing so last night. However hubby attempted to install the new router last night and all seemed to go fine but after installing we couldn't connect to the wireless network through laptops, iphone ps3 etc - even though we could see the network with excellent strength, after hours of trying called TP-Link they went through everything they could think of and still no joy. Gave up in the end and went to reinstall the netgear Router and now we have the same problem with this router, even though earlier in the night it wasn't a problem - we deleted the previous networks so there was nothing stored in memory & tried everything we can think of (although neither of us are brilliant with IT we do usually get by).We even set up an unsecured wireless network (on both routers) and still couldn't connect?
View 2 Replies View RelatedI am a beginner to ASA. I am trying to connect the ASA 5505 behind the netgear ADSL router which is getting dynamic IP address from the ISP. How to configure the ASA5505 outside interface for SSL VPN connectivity?
View 8 Replies View Relatedin my past days i am using bsnl broadband. and also using adsl router for net-connection. i am connecting internet through wifi adsl router. now i am not using bsnl broadband. now i am using beem broadband in hyderabad. that internet connection is directly to my laptop through rj45 cable. but i want to configure adsl router to my beem broadband because i want to connect internet through wifi.it is possible or not? if possible tell me the procedure.
View 2 Replies View RelatedI bought my dad a Netgear N150 DGN1000 Wireless ADSL Router to replace his D-link router which kept dropping the wireless signal. I have established a wired connection and my ipad, iphone and his old laptop connect wirelessy to it without any problems but I just cannot work out why his laptop won't connect to the internet.It recognises the wireless signal and it says its connected and that the signal is excellent but when I try to go on the web or check emails it just won't work.I've tried deleting all his wireless networks and starting from scratch but don't know what else to tryHis PC is running windows Vista
View 9 Replies View RelatedI Got a new ADSL connection,They provided a ADSL Modem. To connect tot he ADSl i have to enter the username/password in the PC....in this case how can i make this ADSL connection to wireless? coz Me and my friend want to use the same connection.
View 1 Replies View RelatedWhat I learned was it was bad to connect directly to the modem because you are left open to the internet. Currently my friend just got the internet and I told them to buy a router but they did not, and just have it directly connected to the modem. Is this fine, because they only have one computer, and it works fine for now, but wouldn't this be prone for attack?
View 3 Replies View RelatedToday I set up a home network:Cable router plugged in to......Homeplug network, (D-Link DHP-307AV/B 200 MBPS PowerLine Homeplugs) plugged in to a LAN port of......a spare adsl router configured as per here: Connecting Additional Routers | Tech Support Forum...with two desktop machines plugged into the LAN ports of the ADSL router.Both of the desktops have got similar specs, are equi-distant from the ADSL router, and are both connected using Ethernet, not wireless.One of them gets a 9MB/sec ADSL [URL]download, the other can't even bring the webpage up and times out if you ask Google to do a search.Taking out the adsl router and plugging the desktop straight into the homeplug gets a network speed of ~13MB/sec on [URL].Plugging a computer directly into the cable modem gives network speeds of ~40MB/sec on [URL] How can I improve on this, and have it so that both machines can access the Interwebnet at a decent bandwidth?
View 8 Replies View RelatedWe operate a home office network (workgroup) of 6 older PCs running Windows XP SP3.It's a Windows based network using a designated "home" PC as a server, and until recently we were using ethernet cables and a hub/switch for sharing files which worked well because we only share small document files, no music or video.The workgroup does not have a shared internet connection, we don't want or need one for what we do, although the individual PC's can connect to the web using USB dongles just for checking e-mail.Recently the ethernet hub died and I decided to take the opportunity to upgrade to wireless file sharing.None of the PCs have inbuilt wireless adapters so I bought a D-Link USB wireless adapter for each PC.I also bought a Netgear N300 router, thinking that this was suitable entry level equipment for wireless file sharing. Now I'm not so sure.So far I was unable to install the router on the "home" PC because the installation CD seems to assume that the router will be used for sharing an internet connection and does not seem to offer an installation option without a standalone modem. How to install this type of router to create a closed home wireless network without a shared internet connection.
View 14 Replies View RelatedI have two netgear wireless modem / router. I want to connect my internet, NAS and Media player on one device (netgear modem/router) and want to link the other netgear in my bedroom and connect another media player and also use the internet via primary netgear modem/router wireless connectivity.
View 1 Replies View RelatedI have one ADSL router that I have configured Port Forwarding on it, but the internet is very slow. I also have another 3G router and I want to use it for internet because it is much faster, but it cannot do Port Forwarding. How can I connect this two routers in one network such that ADSL router is for Port Forwarding only and 3G router is for internet only?
View 1 Replies View RelatedCurrently using a netgear WG602 wireless router which i use to connect to my 2nd PC and Iphone, with the Netgear router running from my main PC.I have recently been having trouble with my 2nd PC ad Iphone randomly losing connection and the only way for the connection to be reastablished is to reboot the wireless router. Once rebooted i am able to connect again to the internet with no problems, interestingly enough my main PC never loses connection. Also sometimes when i lose my connection and reboot the wireless router i will have a IP conflict pop up on my 2nd PC however i would i say i get this once in every 10 dissconects and not all the time. Sometimes i won't dissconect at all in a day but sometimes i may dissconect 5-6 times.
View 1 Replies View RelatedI just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.
Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )
how to properly configure 2 different hardware devices to extend the current wifi signal of my home network.I'm using a Motorola SBG6580 DOCSIS 3.0 cable modem as my primary access point (AP) and a Netgear N300 DGN2200v1 ADSL2+ modem router which will function "behind" the SBG6580 in repeater mode. I previously had DSL for my internet connectivity but recently switched to broadband cable for faster speeds.Due to the layout of my home, I cannot physically connect the Netgear router to the Motorola modem via ethernet cable and need both devices to communicate wirelessly. I have already done extensive reading on this subject and best practices suggest that, whenever possible, both units should be the same brand/manufacturer. The Netgear appliance does have the capability of being configured as a repeater so if I don't have to buy a "network extender" that would be my preference.I understand that both units must be configured to have the same SSID, subnet, wireless channel and security encryption. In repeater mode the Netgear router can't be configured to use WPA2-PSK so I need to use WEP instead.
View 1 Replies View Relatedsomehow connecting my PC to my home network as if it was wired. Having a wired connection just won't work because my PC is far away from my modem and router. The reason I want to connect it wired is because I am getting terrible speeds, and the slowest. [URL]
View 1 Replies View RelatedI have an ADSL connection using a wireless DLink modem 2730U I want to share my internet with my neighbour as limited speed and limited traffic.How can I do this? Is it possible as wireless?
View 4 Replies View RelatedI have a weird problem with my network setup. I have a netgear DG834GT ADSL router which runs fine with my Belkin 51B64C wireless router but when I enable "Use as Access Point" in order for me to see my wireless laptops connected to it the internet performance goes bad, the traffic cuts out momentarily for about 7 seconds at a time, its pretty difficult to surf the net having to wait.The setup is as follows:
Netgear
Gateway IP: 10.0.0.1
Subnet Msk: 255.255.255.0
DHCP Enabled
Belkin
Gateway IP: 10.0.0.9
Subnet Msk: 255.255.255.0
DHCP Enabled
as I said above the reason I enable "Use As Access Point" is so I can see the devices in Explorer for file sharing. Is there a way I can use port forwarding on the router to see the devices it would solve the performance problem.
I am trying to connect a wireless router (EDIMAX br-6228nc) with a ADSL router (NETGEAR). i assigned the LAN IP of the ADSL modem to 192.168.1.1, subnet mask 255.255.255.0, and enable DHCP server.then i connected a LAN port from ADSL router to the WAN port of the wireless router. i assigned IP of the WAN port of wireless router to 192.168.1.10, subnet mask to 255.255.255.0 and default gateway to 192.168.1.1 now on the LAN side of the wireless router i assigned IP 192.168.0.1 and subnet mask 255.255.255.0 enabling DHCP server.on the client pc i selected the setting of automatically assign IP setting (which it got 192.168.0.100, default gateway 192.168.0.1) but my client pc is not able to access the internet.
View 2 Replies View RelatedI have a Netgear DG834G v3 ADSL router which I have had since early-2007.
When I work from home I connect to office networks on a Win7 machine via a Rackspace-provided VPN using Cisco System VPN Client 5. It works well, except for one issue that is costing me time every working day.
I get intermittently disconnected from the VPN, without any warning or apparent reason.
Since I bought the router 5-6 years ago I have had no need to update firmware, so other than ISP configuration I have had no need to change the router at all and I can say it's worked well for me.
What would be the reason for my VPN connection dropping? Is this an ISP issue (my ISP is Carphone Warehouse/TalkTalk) that I have to take up with them or is it more likely a hardware problem with my router or a VPN configuration issue?
My instincts are to not look into VPN config at the moment as I know a colleague who uses the same VPN through a different router and ISP can stay connected for hours, even overnight.
I am using the WNR200v2 for wireless and with a powerline adapter where should I set my speeds, 54Mbps, 145Mpbs or 300Mbps? Are there any other settings I should changeI have a road runner cable modem with 10Mbps download. I am streaming wireless to a PS3 slim 160gb, WDTV LIVE HD media streamer and a Directv HR24-500 DVR. I am using a powerline adapter kit to stream to a Boxee Box another media streamer. Most of my streaming is from the internet but, I occasionally will download something and then stream it from my HDD to one of my media streamers. My wireless signal only needs to travel about 30 ft. and the same for the powerline adapter
View 4 Replies View RelatedWe are getting browser redirects on our Netgear home network. It's happening on 3 computers (2 LAN, 1 wireless) and on a cell phone. Have scanned the computers with AVG, Malwarebytes and Super Antispyware.I have to believe it's in the router
View 1 Replies View RelatedI just ran Cat6 from my WNDR3700 to a netgear NeoTV550. WNDR is in the computer room and the Neo is in the living room. Cat6 had to be fished downstairs, around the bathroom wall and over the solid plaster ceiling. Fun times! My question is, should I add a switch to the connection on the far end, essentially creating a trunk sans dot1.q tagging and then plug the Neo in? Or should I just plug directly into the Neo?
View 3 Replies View RelatedI've been replacing my Netgear WNDR3700 (currently only serving as wired router and gigabit switch) with an Untangle box.Obviously, only the free "Lite" version would be worth it, as the others are priced ridiculously for non business use. I've had a hard time figuring out from their webpage how the features of the "Lite" compare to the others, particularly how Spam Blocker Lite, Web Filter Lite and Virus Blocker Lite compare to the full versions of each.
Is the untangle router any good? How do its management features compare with consumer solutions?The new web caching feature seems really cool too, especially when multiple systems grab the same large updates or download the same steam games, but at $54/year it seems a bit excessively priced for home use, so I'd probably just be sticking with the base free version.
I just moved into a house that has pre-wired CAT5 (Maybe 6) in every room. Its all connected by two Netgear FS116 switches in the attic.
According to my landlord I should just have to plug in my modem into any ethernet port, and internet will be present at every jack.
I've plugged into several of wall jacks and none of them seem to work. Sometimes for a random reason they will work, but the connectivity is so poor that I can't even load webpages. Connecting direct to the modem I receive excellent download speeds.
I am not 100% the cabling is correct, and don't know of any way to test if they are good besides plugging in my modem, and then seeing if my computer gets connectivity.
Is there some easy way I can troubleshoot this? Am I missing something major that I need to accomplish? Like go into the switch and change settings?
Looking for the most efficient setup of my home network. I recently bought the netgear 3700 and it has been great. I also have a trendnet green 8 port giga switch. Both of these will be located in my equipment closet.
I also have an ooma voip hub. before i did the router upgrade i had modem>ooma hub>router. Mainly had it that way since the previous router was a wrg614 and i thought the hub probably had better qos routing. I now have the 3700 infront since i think it does that. I need to learn how to setup the qos though. Problem is that having the hub after the router loses one of my 11 ports (i have pleanty now).
Will speed through the switch be as fast as straight from the router? should my netflix devices connect directly to the router or does any of this matter. [code]
We have a Cisco Firewall 5510.When I VPN into the network, I have to rdp to a windows desktop in order to SSH into my linux boxes.how to ssh ditrectly from home PC.
View 3 Replies View RelatedLately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies View RelatedChanged from D-Link to Netgear router now only one of two computers cannot see the other. Error shows cannot connect to MSHOME network, need administrative approval. Computers are ethernet connected to the router. Have McAffe and both computers are "Trusted" Can do a search with XP and it shows the missing computer but unable to make a connection.
View 5 Replies View RelatedSo I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
View 1 Replies View RelatedMy question is how can I use this existing wi-fi as input to a router to make a sub wi-fi for four computers and a wireless printer. Some of my computers may need to be wired into the router.
View 5 Replies View Related