Home Network Setup Using Netgear Wireless Modem / Router?

Feb 2, 2013

I have two netgear wireless modem / router. I want to connect my internet, NAS and Media player on one device (netgear modem/router) and want to link the other netgear in my bedroom and connect another media player and also use the internet via primary netgear modem/router wireless connectivity.

View 1 Replies


ADVERTISEMENT

Netgear N300 Dgn2200v1 Adsl2+ Modem Router / Extending Wifi Range For Home Network?

Dec 11, 2012

how to properly configure 2 different hardware devices to extend the current wifi signal of my home network.I'm using a Motorola SBG6580 DOCSIS 3.0 cable modem as my primary access point (AP) and a Netgear N300 DGN2200v1 ADSL2+ modem router which will function "behind" the SBG6580 in repeater mode. I previously had DSL for my internet connectivity but recently switched to broadband cable for faster speeds.Due to the layout of my home, I cannot physically connect the Netgear router to the Motorola modem via ethernet cable and need both devices to communicate wirelessly. I have already done extensive reading on this subject and best practices suggest that, whenever possible, both units should be the same brand/manufacturer. The Netgear appliance does have the capability of being configured as a repeater so if I don't have to buy a "network extender" that would be my preference.I understand that both units must be configured to have the same SSID, subnet, wireless channel and security encryption. In repeater mode the Netgear router can't be configured to use WPA2-PSK so I need to use WEP instead.

View 1 Replies View Related

Netgear 3700 Efficient Setup Of Home Network

Jan 16, 2011

Looking for the most efficient setup of my home network. I recently bought the netgear 3700 and it has been great. I also have a trendnet green 8 port giga switch. Both of these will be located in my equipment closet.

I also have an ooma voip hub. before i did the router upgrade i had modem>ooma hub>router. Mainly had it that way since the previous router was a wrg614 and i thought the hub probably had better qos routing. I now have the 3700 infront since i think it does that. I need to learn how to setup the qos though. Problem is that having the hub after the router loses one of my 11 ports (i have pleanty now).

Will speed through the switch be as fast as straight from the router? should my netflix devices connect directly to the router or does any of this matter. [code]

View 7 Replies View Related

Cablenet / Netgear Jnr1010 Wifi Router Setup Without Modem?

Feb 16, 2013

I am having netgear JNR 1010 wifi router and I use Cablenet. the wire which carries internet is directly connected to my Desktop pc's LAN port without modem.Is there any way to install this router without conecting to modem?

View 3 Replies View Related

2 Apple Airport Extremes - Netgear ADSL Router - How To Setup Home Networking

May 21, 2011

Currently, I have 2 Apple Airport Extremes, and 1 Wireless Netgear ADSL Router. The 2 AAEs are connected separately to the router, and this allows us to get coverage in most part of the house (it's a large house with concrete and granite walls). I also have a HP Officejet 8500 'wireless printer' that is wired to the router as you can only print to the printer when it's in standby with a physical connection to the router (that's a different story). So my goal is to replace everything as the router is slowly dying and as a result of this, I want to be able to access the Internet wirelessly throughout the house, and be able to print from any where in the house without anything connected via cables. And as a bonus, I would like the Internet to be accessible 100 yards/metres down the garden (workshop is there). Basically, blanket coverage!

View 3 Replies View Related

How To Set Up A Netgear N300 Router For A Closed Home Wireless Network

Apr 8, 2012

We operate a home office network (workgroup) of 6 older PCs running Windows XP SP3.It's a Windows based network using a designated "home" PC as a server, and until recently we were using ethernet cables and a hub/switch for sharing files which worked well because we only share small document files, no music or video.The workgroup does not have a shared internet connection, we don't want or need one for what we do, although the individual PC's can connect to the web using USB dongles just for checking e-mail.Recently the ethernet hub died and I decided to take the opportunity to upgrade to wireless file sharing.None of the PCs have inbuilt wireless adapters so I bought a D-Link USB wireless adapter for each PC.I also bought a Netgear N300 router, thinking that this was suitable entry level equipment for wireless file sharing. Now I'm not so sure.So far I was unable to install the router on the "home" PC because the installation CD seems to assume that the router will be used for sharing an internet connection and does not seem to offer an installation option without a standalone modem. How to install this type of router to create a closed home wireless network without a shared internet connection.

View 14 Replies View Related

Setup A Netgear Wireless Router On A Company Network?

Dec 4, 2012

i wanted to know if i could setup a netgear wireless router to my ethernet cable that is coming out of the wall. is it as easy as plugging the cable coming out of the wall into the internet port on the router?

View 5 Replies View Related

Creating One Network With Belkin Modem And Netgear Wireless Router

Oct 3, 2012

Basically what is happening is I have a fiber decoder whitch goes into My belkin modem which controls my phone and Internet and with the company I am with we need that modem, I also have a netgear router so I can have wireless through my house but I want to plug LAN into the belkin router and still use the netgear for transmitting wireless.In short I want LAN in belkin but still have the netgear transmitting wireless and everything on the same network,E.g I have a pioneer amp and I use the iPhone app icontrol over my wireless but I can't because the amp is plugged into the belkin and the app is using netgear.

View 1 Replies View Related

Setup 3600HGV As Modem Only / Have Netgear DGN3500 As Wireless Access Point

Apr 19, 2011

I'm trying to find out if it's possible to setup a 3600HGV (VDSL Gateway) as modem only and have a Netgear DGN3500 (ADSL2+) as a wireless access point. I'm aware that both are DSL modems, my reasoning for wanting to have them both hooked up is that

a) the 3600HGV has no Gigabit switch and runs on wireless G

b) the DGN 3500 has a Gigabit switch and does wireless N. So in a nutshell I want the 3600 as simple modem and the 3500 as a wireless N access point with Gigabit switch.

View 4 Replies View Related

Home Network :: Using A Netgear WG602 Wireless Router - PC And Iphone Randomly Losing Connection?

Jun 2, 2011

Currently using a netgear WG602 wireless router which i use to connect to my 2nd PC and Iphone, with the Netgear router running from my main PC.I have recently been having trouble with my 2nd PC ad Iphone randomly losing connection and the only way for the connection to be reastablished is to reboot the wireless router. Once rebooted i am able to connect again to the internet with no problems, interestingly enough my main PC never loses connection. Also sometimes when i lose my connection and reboot the wireless router i will have a IP conflict pop up on my 2nd PC however i would i say i get this once in every 10 dissconects and not all the time. Sometimes i won't dissconect at all in a day but sometimes i may dissconect 5-6 times.

View 1 Replies View Related

Linksys Wireless Router :: RE1000 Won't Get Home Network Setup

Aug 25, 2012

Firstly I cannot get my Linksys RE1000 to work with my network having tried the set up CD on 2 computers (mac and windows). The main router is a BT Home Hub 2.0
 
The main router is in the basement where out internet connection enters the house, also in the basement is our LAN board where we have ethernet cables extending to parts of the house. There is weak wireless signal from groundfloor up to the top floor so wanted to find something where I could plug into the ethernet port and it would broadcast an wireless network to the upper floors/areas with a weaker signal. Thought the RE1000 would do this job but i can't get it to do it wirelessly let alone connect it to the main router using a ethernet cable. 

View 2 Replies View Related

Linksys Wireless Router :: E1000 - Home Network Setup Without Internet?

Dec 25, 2011

Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?

View 2 Replies View Related

Linksys Wireless Router :: Home Network E1000 Setup Without Internet Access?

Aug 3, 2011

Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?

View 3 Replies View Related

Linksys Wireless Router :: E3000 - How To Setup Iomega Home Media Network

Jan 26, 2013

I'm trying to set up an Iomega Home Media Network Cloud NAS and I'm having problems with opening ports 50500-50599.  I have opened port 80 and 443 successfully and included the above port range above as well, but when I check it on www.yougetsignal.com the ports 50500-50599 are still closed.  I even tried to split the range in two parts, and still no success.  I have been in contact with my ISP and confirmed they do not block any ports in the 50500-50599 range and that the cable modem (a Motorola SBV5120) is operating in Bridge Mode.

View 3 Replies View Related

Home Network :: Advanced Home Network Setup (3 Subnets) And Port Forwarding?

Feb 24, 2013

I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:

- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface

Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.

- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.

- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.

Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.

Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)

Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).

View 5 Replies View Related

Home Network :: Router Not Getting IP From Modem?

Feb 12, 2012

so yesterday I went out and bought a new Cisco Linksys E4200v2 router. My ISP is Communicomm (terrible, but they're the only one here). I also have a Terayon TJ 715x cable modem. I shut down pc & cable modem, connected everything, and powered back up. I am able to access the router config page at 192.168.1.1, but the router does not receive an ip address from the modem. If I plug the modem directly to the pc, I get an ip and am able to connect to the internet. I have called my ISP several times, and they tell me that they do not use MAC address filtering. The only MAC address that they need is that of the modem, which they have. This modem has been working fine for several years. After spending over an hour on the phone with Linksys support, they have determined that the router is functioning properly.I also tried hooking up an older netgear router and got the same results. The following is my ipconfig with the modem connected directly to the pc. [CODE]

View 4 Replies View Related

Home Network :: Connect A Netgear FS605 Directly To ADSL Router

May 12, 2012

I want to connect a Netgear FS605 directly to my ADSL router.However I find that this does not work unless I put my Netgear EN2005 Hub in between the Switch and the Router.The Hub is 10Mb/sec the switch 100Mb/s so I would like to eliminate the hub.

View 3 Replies View Related

Netgear Router / Setup An Internal Network In One Room Of A Building?

May 1, 2012

internet provided to whole building with connections in every room -> personal router in my room -> my PCs, Macs & printer, how to set up my computers so that they can share files with each other and print to my network printer, but without being susceptible to being accessed from other computers in the building? I have my own netgear router. But at the moment, my shared folders are accessible by everyone in the building, so is my printer If I set all the computers to automatically set ip by DHCP, they can access the net, but everyone in the building can access them (and my printer which requires a manual ip doesnt work). If I set all the computers to manual addresses (e.g. 192.168.1.14 ... 192.168.1.15 ... 192.168.1.16 etc.) they work with each other, the printer works, its secure, but I can't access the internet!Is there a way to for example have my own internal network with manual ip addresses, while also being able to connect to the net?

View 1 Replies View Related

Home Network :: PCs On Modem Can't Find PCs On Router?

Oct 3, 2011

I have a wireless modem on the first floor of my house, where I got cables through the wall running throughout rooms in first floor, ground floor and basement.I have my small business at the basement, so I have 2 PCs one printer and one external hard disc which also connects directly to a modem/router.I have 3 PCs from the first and ground floor that connect through the wall to my modem, and everything works well. But for my basement, which only has 1 lan cable output on the wall, I got myself a router so that I can connect all my devices.I connect the router with my modem, and then the PCs, printer and hard disc on the router. The PCs have internet access, so I know the connection to the modem has nothing wrong to it. But I am not able to access the PCs connected to the router from the PCs connected to the modem, or vice versa.

I was told to not obtain an IP address automatically, so I assigned my modem and router to work on 192.168.10.x and gave my PCs IPs such as 192.168.10.19 Only after setting this up did all my PCs have internet access, but again, no network communication between PCs on modem and PCs on router.One thing that might be worth mentioning, is that through time, my network keeps going from Home Network: Network, to Network 2, Network 3, and so on... now it's on Network 5. I have no clue why this happens, and if it's related to my problem

View 2 Replies View Related

Home Network :: Cannot Setup NAT On Edimax Router

Aug 10, 2012

Cannot setup NAT on edimax router I ve got this setup: [URL] It works well - I can connect from TESTPC and LAPTOP (bottom left corner) to SERVERS A/B/C (bottom right corner) without any problem. Everything seems to be routed perfectly, however from SERVERS A/B/C I cannot ping TESTPC and LAPTOP, and I can't even establish an RDP connection.I was told to setup static routes or NAT, but I am at a loss on how to do it. I am using an EDIMAX BR-6424NL wireless router ?

View 1 Replies View Related

Home Network :: Can't Get Usb Modem To Connect To The Internet With Router

Jul 16, 2012

I'm having trouble connecting my 02 dongle to the internet using my router. My router is a TP-LINK MR3420 and my 02 modem device is E1752. I checked to see if the modem is compatible and it says it is. I went through the configuration that was given to me with the router and I tried using you tube but nothing. Do i need to get a static I.P address off my Internet provider? If I plug my 02 usb dongle directly into my computer it works perfectly and I got the router to work using a ethernet cable and plugging it into the WAN port at the back of the router but I would prefer to let it connect through the 3g port. I get a connection at 40% and 100 bytes are sent and some are received but the connection drops. Is it a problem with the connection? I will upload a image.

View 3 Replies View Related

Dir-615 Dlink Router - How To Setup Wifi Home Network

Oct 13, 2011

I have a dir-615 D-link router. It is well installed with my main computer that is an old XP windows system. I tried to create a network to give acces to my friend laptop when he comes home(he has a mac). I setuped a network with a name and a password. So my friend could find the network name and i gave him the password, but it never works. Another friend of mine also came with an older iBook laptop and the same thing happens.

View 5 Replies View Related

Home Network :: 2 Router Setup / Which Way Is Communication When Transferring

Apr 15, 2012

1 Virgin media home home up stairs in the home office. Ether cable running from the home hub, outside the house to the downstairs lounge with an ethernet socket on the end. Cable from the socket into a dlink router (set to operate as a hub).My reason for this setup was due to the rubbish wireless signal from the virgin hub, and the fact that I have various other bits of kit downstairs that I could use an ethernet cable with.The question is, IF my laptops are connected to the router downstairs by an ethernet cable and I want to transfer some files between them, will the data be routed through the virgin media hub upstairs before coming back to the router that both laptops are connected to downstairs? I have just done a test with 30gb worth of files and the transfer speed was 8.7MB/second, is that good for wireless?

View 1 Replies View Related

Netgear Router (DGN1000) Unable To Connect Wirelessly To Secured Or Unsecured Home Network

Feb 15, 2012

I'll try and keep this brief, we were having problems with our netgear router (DGN1000) mainly with connection when online gaming with PS3, generally poor connection - so purchased a TP-Link router (TD-W8960N). We could usually access the netgear wirelessly on our laptops Dell and Acer Aspire 4820T (both Windows 7) without any problems and were still doing so last night. However hubby attempted to install the new router last night and all seemed to go fine but after installing we couldn't connect to the wireless network through laptops, iphone ps3 etc - even though we could see the network with excellent strength, after hours of trying called TP-Link they went through everything they could think of and still no joy. Gave up in the end and went to reinstall the netgear Router and now we have the same problem with this router, even though earlier in the night it wasn't a problem - we deleted the previous networks so there was nothing stored in memory & tried everything we can think of (although neither of us are brilliant with IT we do usually get by).We even set up an unsecured wireless network (on both routers) and still couldn't connect?

View 2 Replies View Related

Home Network :: Netgear Router WNR 2000 V3 - Cannot Access Internet When Security Password Chosen?

Apr 13, 2013

I just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.

Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )

View 2 Replies View Related

Setup A Wireless Network Within Home?

Apr 27, 2012

I am trying to set up a wireless network within my home, i have a external hard drive and was wondering can i connect this to my internet router to make it accessible in order to stream music and movies from the hard drive. there is no ethernet port on the hard drive but seen a usb to ethernet adapter is this all that would be needed?

View 1 Replies View Related

Routers / Switches :: Setup An Home Network With A Wireless Router And Use Multiple Switches?

Jan 29, 2011

I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.

View 3 Replies View Related

Home Network :: Connection Between Router And Cable Modem Goes Off At Specific Time?

Jul 20, 2011

Lately I've been experiencing connection problems between my router and cable modem. Every night after 11:00 PM EST, my Internet connection sporadically goes out. I called my ISP who said there was nothing wrong on their end. Plugging directly into my modem allows me to access the Internet. When I wake up in the morning, the connection is back until 11 or later again. I ran WireShark but I'm not sure what to be looking for. There are a lot of random things from the LLMNR protocol like standard query A zmtvrjaql.

View 2 Replies View Related

Home Network :: How To Setup Wireless Bridging

Sep 11, 2012

I have this setup at home and I can't make wireless bridging to work with two WR740N routers.I tried 3 online tutorials and none of them worked

R1,R2,R3 = routers
The main router "R1" Is setup like this :
IP Address 192.168.100.1
DHCP enabled 192.168.100.120 - 192.168.100.150
Gateway 192.168.100.1

[code]....

View 1 Replies View Related

Home Network :: ARRIS TM822 - Bridging Cable Broadband Modem To Router

Feb 18, 2013

i have an ARRIS TM822 cable modem provided by comcast, in addition i have a linksys e3000 wireless router. what i am trying to accomplish is to bridge the cable modem over to the router. i messaged comcast about this issue and i have attempted what they told me to do, but im not getting any where.

View 1 Replies View Related

WEP Security Setup - Can't Connect To Home Wireless Network

Feb 23, 2013

I have a work supplied laptop. Used to be able to connect to my home wireless network - this stopped working last week. It can connect to other wireless networks, both at the office and other public places, but can't connect to my home network.

I've tried: Manually creating the wireless network Removing the profile from regedit Removing the profile from ProgramDataMicrosoftWlansvcsProfiles

It sees the network and attempts to connect, but never successfully connect. I have other laptops at home that are working just fine. The network is setup with WEP security, and I've entered/reentered the password several times.

Note, when I started this, the home network did not appear under the Manage Wireless Networks list in the Network and Sharing Center.

View 1 Replies View Related

Home Network :: ADLS Modem Cannot Send Wireless Packets

Aug 6, 2012

I had Symfony modem with Asus ap and 1 d-link switch. i changed my modem because that was old and bought TP-Link(TD-W8961ND).It is connected to the Dlink switch and the switch is connected to the Asus Ap(RT-N12) The situation was the same just modem has been changed. Now i have this problem: i have internet with cable every where...behind switch or behind Ap...but when i wanna use internet with wireless via Asus Ap it doesn't work i checked every thing...the Asus Ap has 3 mode(Ap,Router,Repeater)...i chose every one but only repeater mode works. by the way with modem wireless i can get to the internet but the signal is fair for me to use!

View 9 Replies View Related

Wireless :: Toshiba Soft Modem AMR Com3 Trying To Connect To Home Network

Dec 18, 2011

Ok I have a toshiba satellite with the above stated modem in place, however I am not sure if the modem is wireless capable. I have been trying to figure out how to connect it to my network.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved