Connecting Wireless (Edimax Br-6228nc) To ADSL (Netgear) Router

Jan 10, 2012

I am trying to connect a wireless router (EDIMAX br-6228nc) with a ADSL router (NETGEAR). i assigned the LAN IP of the ADSL modem to 192.168.1.1, subnet mask 255.255.255.0, and enable DHCP server.then i connected a LAN port from ADSL router to the WAN port of the wireless router. i assigned IP of the WAN port of wireless router to 192.168.1.10, subnet mask to 255.255.255.0 and default gateway to 192.168.1.1 now on the LAN side of the wireless router i assigned IP 192.168.0.1 and subnet mask 255.255.255.0 enabling DHCP server.on the client pc i selected the setting of automatically assign IP setting (which it got 192.168.0.100, default gateway 192.168.0.1) but my client pc is not able to access the internet.

View 2 Replies


ADVERTISEMENT

Netgear DG834GT - 192.168.0.1 - Connecting Two Routers With Separate ADSL Connections

Aug 9, 2011

how to connect 2 routers that both have an ADSL connection. When attempting this the Belkin router will lose the ADSL connection after a random amount of time.

View 5 Replies View Related

Cisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?

Aug 24, 2012

i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday   the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?

View 2 Replies View Related

Connecting Non-wireless Desktop To ADSL Router?

Feb 22, 2013

My desktop however, does not have built-in wireless and therefore would have to connect to the ADSL router (Netgear) through ethernet but this cannot be done as the router must remain in my bedroom, much too far away for cables to reach.I bought a USB wireless connecter for the desktop but it doesn't seem to work. It connects but gives "Local Only" as the connection.

View 9 Replies View Related

Can't Connect Toshiba Laptop Wirelessy To Netgear N150 DGN1000 Wireless ADSL Router?

Jan 13, 2012

I bought my dad a Netgear N150 DGN1000 Wireless ADSL Router to replace his D-link router which kept dropping the wireless signal. I have established a wired connection and my ipad, iphone and his old laptop connect wirelessy to it without any problems but I just cannot work out why his laptop won't connect to the internet.It recognises the wireless signal and it says its connected and that the signal is excellent but when I try to go on the web or check emails it just won't work.I've tried deleting all his wireless networks and starting from scratch but don't know what else to tryHis PC is running windows Vista

View 9 Replies View Related

Netgear Wireless ADSL Firewall Modem Router DG834 / Connection Loss - Routers Or ISPs Fault

Apr 14, 2012

Lately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.

View 4 Replies View Related

Edimax EW-7416APn V2 / Connecting Broadband Modem To Access Point?

Aug 25, 2012

I have internet over LAN with Motorola SB5102 broadband modem. Is it possible to share this internet on Edimax EW-7416APn V2 access point?

View 1 Replies View Related

Netgear DG834GT ADSL - Use Access Point And Router?

Feb 23, 2011

I have a weird problem with my network setup. I have a netgear DG834GT ADSL router which runs fine with my Belkin 51B64C wireless router but when I enable "Use as Access Point" in order for me to see my wireless laptops connected to it the internet performance goes bad, the traffic cuts out momentarily for about 7 seconds at a time, its pretty difficult to surf the net having to wait.The setup is as follows:

Netgear
Gateway IP: 10.0.0.1
Subnet Msk: 255.255.255.0
DHCP Enabled

Belkin
Gateway IP: 10.0.0.9
Subnet Msk: 255.255.255.0
DHCP Enabled

as I said above the reason I enable "Use As Access Point" is so I can see the devices in Explorer for file sharing. Is there a way I can use port forwarding on the router to see the devices it would solve the performance problem.

View 15 Replies View Related

Wireless :: Netgear Router Stopped Connecting?

Jul 23, 2011

My NetGear router stopped connecting to the internet. The internet light, which is usually orange, is now yellow and flashing. I tried rebooting everything and now, when it connects it says "local access" so I can't get on the net

View 3 Replies View Related

Netgear MR 314 - Wireless Router Not Connecting To Internet

Oct 9, 2011

i have an old Netgear MR 314 router that works like a charm for my wired connections, but whenever i try to connect wirelessly from my phone or laptop, it connects but doesn't access the internet.

View 5 Replies View Related

Home Network :: Connect A Netgear FS605 Directly To ADSL Router

May 12, 2012

I want to connect a Netgear FS605 directly to my ADSL router.However I find that this does not work unless I put my Netgear EN2005 Hub in between the Switch and the Router.The Hub is 10Mb/sec the switch 100Mb/s so I would like to eliminate the hub.

View 3 Replies View Related

Cisco Firewall :: How To Connect ASA5505 Behind ISP Netgear DG834 ADSL Router

Jan 30, 2010

I am a beginner to ASA. I am trying to connect the ASA 5505 behind the netgear ADSL router which is getting dynamic IP address from the ISP. How to configure the ASA5505 outside interface for SSL VPN connectivity?

View 8 Replies View Related

Netgear DG834Gv3 ADSL Router Dropping Rackspace VPN Connection Intermittently

Feb 7, 2013

I have a Netgear DG834G v3 ADSL router which I have had since early-2007.

When I work from home I connect to office networks on a Win7 machine via a Rackspace-provided VPN using Cisco System VPN Client 5. It works well, except for one issue that is costing me time every working day.

I get intermittently disconnected from the VPN, without any warning or apparent reason.

Since I bought the router 5-6 years ago I have had no need to update firmware, so other than ISP configuration I have had no need to change the router at all and I can say it's worked well for me.

What would be the reason for my VPN connection dropping? Is this an ISP issue (my ISP is Carphone Warehouse/TalkTalk) that I have to take up with them or is it more likely a hardware problem with my router or a VPN configuration issue?

My instincts are to not look into VPN config at the moment as I know a colleague who uses the same VPN through a different router and ISP can stay connected for hours, even overnight.

View 1 Replies View Related

Connecting Layer2 Switch To ADSL Router

Nov 20, 2011

A Layer 2 switch with IP Address 192.168.1.4 (Vlan0), subnet 255.255.255.0 is physically connected to ADSL Router with IP address 192.168.1.1 (which is also the gateway address for the switch). The problem I have is that all the devices connected to the switch can intercommunicate but are unable to communicate with devices connected to the Router. I guess this may be something to do with how the Vlan is configured on ADSL router?

View 1 Replies View Related

Connecting Wifi Router To Adsl Modem

Nov 22, 2012

I have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?

View 1 Replies View Related

2 Apple Airport Extremes - Netgear ADSL Router - How To Setup Home Networking

May 21, 2011

Currently, I have 2 Apple Airport Extremes, and 1 Wireless Netgear ADSL Router. The 2 AAEs are connected separately to the router, and this allows us to get coverage in most part of the house (it's a large house with concrete and granite walls). I also have a HP Officejet 8500 'wireless printer' that is wired to the router as you can only print to the printer when it's in standby with a physical connection to the router (that's a different story). So my goal is to replace everything as the router is slowly dying and as a result of this, I want to be able to access the Internet wirelessly throughout the house, and be able to print from any where in the house without anything connected via cables. And as a bonus, I would like the Internet to be accessible 100 yards/metres down the garden (workshop is there). Basically, blanket coverage!

View 3 Replies View Related

Cisco WAN :: Connecting 1900 Router To Adsl Modem

Dec 9, 2012

i have  one airtel isp connection was connected to beetel adsl modem and this  modem is connected to d-link switch to accessing internet for my lan.  and one netgear wireless router is aslo connected to this d-link switch.  my need is i has one cisco 1900 router, i want to get internet access  from adsl modem or netgear router to my cisco router.

View 1 Replies View Related

Netgear WGR614v9 - Connecting 3G Mobile Broadband To Wireless Router

Mar 18, 2011

I've got an Optus (in Australia, so 3G mobile broadband is all that matters I would think) that I'm trying to connect to a Netgear WGR614v9 wireless router. So the 3g mobile plugs into usb on computer; the router to the ethernet card on computer.

I know; I could buy one that has it in one package, but we're throwing the router out from work anyway. If this works my daughter will be thrilled with her iPod more is all :)

I've got the mobile broadband on, and plugged in the router and Windows 7 makes a second network connection automatically for the router, though with no internet access, and the setup wizard in the router claims to have no access to the internet. (though clearly I'm posting...lol).

We can see the Wireless signals on devices and can connect to the router but then the devices say no internet access when you actually try to access the web, like the router wizard does. and yet, we are online

View 2 Replies View Related

Linksys Wireless Router :: Connecting WRT610n And Netgear WNR2000v2?

Aug 4, 2011

I am having trouble getting the wrt610n to connect to the wnr2000v2 that can be set a  wireless repeater.  I had a 160n hooked up and it was working fine, but am unable to get the 610n going on it.  setting this type of networking up , but have a general idea of how it works.  I have the 610n running and is broadcasting a signal, but the wnr 2000 will not connect to it wirelssly and repeat it.  The setup in the netgear is pretty basic , but I am new to the linksys 610n and the interface that's why I believe it has to do with the 610n. 

View 3 Replies View Related

Belkin F5D7633 Connecting WIMAX Internet To ADSL Router

Mar 12, 2013

I have a Wimax internet connection via an ethernet cable from a small roof top receiver dish. Inside the house the cable (RJ45) is plugged into the POE slot on one side of a small electrically powered black box, and from the other side, an ethernet cable (RJ45), connects to my PC. I want to share my internet connection with my HTC mobile and would prefer to make use of an existing Belkin 54g ADSL2 modem/wireless router (Belkin F5D7633) if I can. As this router's incoming port is specifically for ADSL my internet RJ45 cable can not plug into it. I have been advised that I can still utilise the router part of the Belkin though, using my PC as an access point, by plugging the ethernet cable from the PC side of the little black box into LAN 1 on the router, then joining the PC to LAN 2 of the router with another ethernet cable.I did not alter the configuration of the Belkin at all (having reset factory defaults beforehand), mainly because although I could access the internet from my PC and my mobile, I could not access the IP address of the router, presumably because the properties of the local area connection on my PC remained unchanged with the IP address (172.168.1.149), Subnet Mask (255.255.255.0), Default Gateway (172.168.1.1) and 3 DNS addresses (172.168.1.1) (10.30.0.1) (8.8.8.8) as they were before hooking up the Belkin. The IP address the mobile received through WIFI on connecting to the Belkin was 172.168.1.148

I was not unduly concerned about not being able to access the configuration of the router as everything was working as I had hoped it would and even when I powered off my PC I still had internet access on my mobile. On rebooting the PC, however, I found that the router changed the DNS addresses on the PC to 2 only, both identical (192.168.2.1) and the IP on the mobile was allocated 192.168.2.2 Although I could still access the internet on my PC, I no longer had access from my mobile although the WIFI connection to the Belkin showed as being 'excellent'. When I did a 'repair' of my internet connection, hoping to revert to a fully operative state, the PC configuration changed again as follows: IP address becomes that of the router (192.168.2.1), Subnet Mask (255.255.255.0), Default Gateway (192.168.2.1), 2 DNS addresses (192.168.2.1) and the IP address allocated to my mobile remains (192.168.2.2) This configuration means I have no internet access from either PC or phone, but CAN access the router configuration. I restored a usable operating state by unplugging the power from the router, transposing the cables in the LAN ports on the router (swapped cable from LAN1 to LAN2 and vice versa), turned off WIFI on mobile and waited a minute or two. When I powered the router back up and switched on mobile WIFI again, everything was restored to the original working state and I have, once again, access to internet on both PC and mobile. It is very frustrating, however, to keep performing this ritual and I wonder if any of you more technically minded, know a way to work around this, perhaps by manually changing the configuration of PC or router?

View 3 Replies View Related

Cisco Switching/Routing :: 1700 ADSL Router - Connecting 2 Sites Together

Jan 23, 2012

We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.

We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?

Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.

View 9 Replies View Related

Edimax EW-7612 Wireless Adapter Can't Ping Router

Jun 21, 2011

Wireless network is fine - both my laptops get on without a problem.The Edimax PCI-E adapter:

a) can't connect, or

b) has limited connectivity, or

c) has full connectivity but no web pages work, and the router can't be pinged, or

d) works (for a short while)

The above options are seen pretty much evenly, except for the last one which achieves disproportionately low representation.Have attempted to uninstall/reinstall drivers. Have attempted to delete all profiles. Have seriously considered ripping out the PCI-E and throwing it into the next-door neighbours garden, but fear this may damage the motherboard.

View 3 Replies View Related

Enabling Wireless Adapter Knocks Out Edimax 7266 Router?

Nov 25, 2012

I have a new HP lap top which I have connected to the net thro my edimax 7266 routerI also have another lap top and desktop connected via this router. This other lap top I can connect either wired or wireless so the router seems to be working perfectlyThe problem is when I enable the HP laptop wireless adaptor and try to connect to the net . As soon as I do this the orange light on the router goes solid from blinking and I cannot then access the net from any of the computers either wired or wireless. I have to disable the HP wireless adaptor and reboot the router to get a connection on the computers.

View 1 Replies View Related

Home Network :: BR-6228nC - Internet Drops Out When Copying Files Over LAN?

Apr 29, 2012

I can't seem to access the Net when transferring large files between my desktop (WinXP SP3, 100Mbps net card) and my laptop (Win7, 54Mbps WiFi). I have an EDIMAX BR-6228nC 150 Mbps broadband router to which my desktop is wired and the laptop connects through WiFi. The speeds never go above 2.5MBps, so there should be plenty of bandwidth left for Internet use. My router config confirms that there's no Internet connection while transferring the files.

View 1 Replies View Related

Connecting Dell Inspiron 17R To Netgear Router?

Aug 10, 2011

Ive been having problems with the Wireless connection on my laptop for a while now. Basically even though the signal strength is shown as excellent and hovering over the little monitor in notification area shows "Internet access" i cannot connect to the Internet via WiFi. The strange thing is when i connect an Ethernet cable the signal strength on the bottom goes up and i get Internet access but the computer seems to think its got a wireless connection, even though its actually a wired connection. Ive already tried the following

Driver Update
Windows Update
AntiVirus/Malware Scan
Firewall/Anti Virus Off
Ethernet Connection Disabled and Enabled
Changed router channel
reset wep key numerous times
Network Scan (no problems found)

System Information

Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.110408-1631)
Processor: Intel(R) Pentium(R) CPU P6200 @ 2.13GHz (2 CPUs), ~2.1GHz
Memory: 4096MB RAM
Available OS Memory: 3892MB RAM

[code]....

View 14 Replies View Related

Netgear Router / Wifi Not Connecting To Network Periodically

Dec 24, 2012

I am running an i7 MSI gt683 with windows 7 with an Intel Centrino Wirelss-N 130. My home wifi connection runs off of comcast on a netgear router, and the wireless connection works on every single device in the house except for my laptop. I can run my ps3, my wii, we have an ipad, all our phones can connect and we have another laptop that connects with no issue. I have updated my drivers for my wireless card to the latest, flushed the ip on my desktop that the modem is connect to a dozen times. The only way to sometimes fix it is to manually log in to my router and release/renew the ip address from there. Sometimes it will work, sometimes it won't. When it does work, it will work for about a week and then stop working for no reason at random times.The errors I keep getting are:Identifying network (which runs infinitely before cycling back to no internet connection)Connected with no internet access.

View 5 Replies View Related

Connecting Netgear N300 To 2wire 2701 Router?

Mar 8, 2011

How do you connect two routers together to increase signal through the whole house? I am trying to use the n300 as my main router (its hooked to cable modem) and use the 2wire as an access point.The two are connected by a known good ethernet cable.

View 2 Replies View Related

DGN2200 - Connecting Netgear Modem With DLink Router?

Dec 24, 2011

how can i connect a Net gear DGN2200 wireless modem router to a D link DGL4500 wireless router ??

View 1 Replies View Related

Connecting Netgear To Linksys Router To Expand Network?

Jul 6, 2011

I have a netgear CVG834G main router, were my desktop is plugged on to.I pulled a new cable trough the house and garage to have internet access on the other side (cable length is about 80 meters).After the 80meters of cable I placed a Linksys WRT54GS v5.1 router. The problem is that I can connect to the Linksys, but the Linksys can�t connect to the netgear. On the Linksys the internet LED is blinking very slowly (what does this mean?). So first I thought that the cable was broken or too long. I tested the cable => not broken. I connected the Linksys with the netgear trough a shorter cable and then connected my laptop via the long cable (80meter) and this works perfectly.Is the maximum distends a netgear can take less than 80 meters? (thought is was 100meter ).

View 3 Replies View Related

Connecting Netgear R6300 Wifi Router To Old Gateway?

Oct 3, 2012

I have been using a cable modem gateway - Netgear CGD24G from Charter for two years. I just bought Netgear R6300 wifi rounter in order to upgrade the speed and range for my internet. My goal is to upgrade 802.11g to 802.11ac. Is there any special way to setup it up? Or do I need to contact Charter to replace a new gateway?

View 7 Replies View Related

Fios Router Connecting To A Netgear Range Max PCI Card?

Jun 26, 2012

Im having problems staying connected to my internet. I have Verizon Fios router that is wired into this desktop i also have 2 laptops and now im trying to connect a second desktop wirelessly to the router. My Netgear Rangemax PCI picks up the signal at 68% and connects to the router. But periodically it disconnects from the router and i click connect to a network icon and it shows that i have no wireless internet as if no PCI card is installed so i wait a min then it shows up again and windows network diagnostic kicks in and "resets the network adapter" and all is well for about 15min till it disconnects again.

View 1 Replies View Related

Netgear USB Wireless Not Connecting

Jun 9, 2011

I cannot get my USB N adapter to connect with a u-verse G router

View 4 Replies View Related

Connecting PC (Windows 7) To Router (Netgear DGN2000) Via Ethernet Cable?

Oct 18, 2012

I am having problems connecting my PC (Win7) to my Router (Netgear DGN2000) via ethernet cable.Wi-fi is working fine but I want to speed up my connection using the PC's Gigabit port. Here are the problems:

- When connecting via wi-fi everything is fine

- When enabling my LAN WITH wi-fi still enabled I lose all internet connectivity

- When enabling my LAN and disabling wi-fi lose all internet connectivity

Here is my IP Config when both are enabled :

Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.

C:Windowssystem32>ipconfig

Windows IP Configuration[code].....

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved