i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 RepliesI've been looking to see if its possible to create a GRE tunnel between a Cisco 2901 with 3 adsl WIC cards and a Cisco ASA.The Cisco 2901 is at our remote office and we have 3 adsl lines for resillience as they tend to go down alot.The Cisco ASA is at our Head Office sitting behind our ISP's managed router.
The desired end result would be to have three GRE tunnels, 1 for each DSL line terminating on the ASA at head office and use EIGRP routing protocol to move traffic across to another tunnel should one fail, and encapsulate all of that with IPSEC.
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies View RelatedI have a broadband router (Linksys E1000) which I've flashed with a DD-WRT firmware. After doing so I realized that this router doesn't have an interface for ADSL port(RJ-11). How can I use the Linksys E1000 for my home network?
I've heard that I can use ADSL modem(not a router) & plug the RJ-11 to it & take from it the Ethernet & plug it back to the E1000(in the WAN port) would that mean that I can get just a modem and not a hybrid?
Note: Also, I have to mention that my ISP is using PPPoA & DD-WRT is not supporting it, but i googled & they said that the ADSL modem cab be the rescue. Can I pick any ADSL modem for this specific scenario or am I looking at a specific model?
Secondly, can I use my old router to do the job instead of buying a new ADSL modem ? & is it a good approach ? or should i buy a new ADSL modem ?
Update i turned my DD-WRT router(E1000) to act as access point, since this is the only way that i can use it with the DD-WRT feature. & i think this is better than have nothing :) I can now have the DD-WRT functions ;)
I can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great
View 1 Replies View RelatedI have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies View RelatedWe have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
The setup is a S2S VPN with failover to 3G HWIC in a Cisco 1941 however the IPSEC tunnel needs to remain up through 3G if ADSL fails.The failover works ok, however when plugging ADSL back in, the - "sh crypto session" shows both dialer 0, and dialer 1 with the crypto map session to the other side of the VPN and either side is now not pingable.The NoIP DDNS updater client runs on a server in the network and all IP resolution to host1,host2 works ok (other side of VPN is Cisco 1921 with ADSL HWIC and 3G HWIC). [code]
View 5 Replies View RelatedWe have a fairly major problem with some of our Cisco 877 units (5 in all). All are running 15.2(2)T2 in order to make use of zone-based firewalls and virtual reassembly, and all are exhibiting the same problem. When our ADSL line drops this si shown in syslog
2010-11-09 01:03:06 Local7.Info 192.168.7.1 4733: Nov 9 01:03:05.707: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41799 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident 02010-11-09 01:04:06 Local7.Info 192.168.7.1 4734: Nov 9 01:04:05.946: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41809 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident
[code]...
The "no retrain. sleep 20 seconds" messages continue forever more until somebody power-cycles the router - which is a bit inconvenient as two are 300 miles away. Surprisingly, our event manager applet isn't triggering the reload either, which defeats the object.
I have D-link 2640U ADSL2+ modem. Now I have 12Mbps / 1Mbps internet connection. I am planning to move to 24Mbps /1Mbps intenet connection and I want to know if this modem is enough. What is the best modem so I get the full 24Mbps[CODE]
View 7 Replies View RelatedADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.
sh ver
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 31-Jul-07 20:24 by alnguyen
ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes
System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012
System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)
Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??
And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
View 2 Replies View RelatedCan I install 2 ADSL routers on one telephone line with SKY. If I can does this mean that if sky give me 20mb connection, I can get two lots of 20mb using the two routers.
View 2 Replies View RelatedI have ADSL router Linksys X3000, but I have an issue with it. I have configured it properly (based on internet provider's manual), repeatedly checked it, but router still says that ADSL line is down. I have also another router from Zyxel and it works perfect with same wire and configuration, so I guess the line is fine.
PPP generic driver version 2.4.2 79 PPP Deflate Compression module registered 88 PPP BSD Compression module registered 84 PPPoL2TP kernel driver, V1.0 75 ccp_autowan_sm_thread=> Starts in Unconfigured mode, detecting state! 125 ->
[Code]....
Is there a way to find in a remote branch the adsl line number in a cisco router 886VA.
When giving show controllers vdsl 0
we can see the upload/download speed but there is no information about the line number. We need this information in order to troubleshoot adsl line problems with our ISP's in remote branch offices.
I do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?
A Layer 2 switch with IP Address 192.168.1.4 (Vlan0), subnet 255.255.255.0 is physically connected to ADSL Router with IP address 192.168.1.1 (which is also the gateway address for the switch). The problem I have is that all the devices connected to the switch can intercommunicate but are unable to communicate with devices connected to the Router. I guess this may be something to do with how the Vlan is configured on ADSL router?
View 1 Replies View RelatedMy desktop however, does not have built-in wireless and therefore would have to connect to the ADSL router (Netgear) through ethernet but this cannot be done as the router must remain in my bedroom, much too far away for cables to reach.I bought a USB wireless connecter for the desktop but it doesn't seem to work. It connects but gives "Local Only" as the connection.
View 9 Replies View RelatedI have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
View 1 Replies View Relatedi have one airtel isp connection was connected to beetel adsl modem and this modem is connected to d-link switch to accessing internet for my lan. and one netgear wireless router is aslo connected to this d-link switch. my need is i has one cisco 1900 router, i want to get internet access from adsl modem or netgear router to my cisco router.
View 1 Replies View RelatedSite A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
View 1 Replies View RelatedOn my old router I could access the line stats on the home page giving me Attenuation and SNR margin, this allowed me to keep an eye on line quality, there seems to be no equivalent info on the X2000. Is this on a hidden page like the advanced wireless page.
View 1 Replies View RelatedRegion : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net
Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
I have a Wimax internet connection via an ethernet cable from a small roof top receiver dish. Inside the house the cable (RJ45) is plugged into the POE slot on one side of a small electrically powered black box, and from the other side, an ethernet cable (RJ45), connects to my PC. I want to share my internet connection with my HTC mobile and would prefer to make use of an existing Belkin 54g ADSL2 modem/wireless router (Belkin F5D7633) if I can. As this router's incoming port is specifically for ADSL my internet RJ45 cable can not plug into it. I have been advised that I can still utilise the router part of the Belkin though, using my PC as an access point, by plugging the ethernet cable from the PC side of the little black box into LAN 1 on the router, then joining the PC to LAN 2 of the router with another ethernet cable.I did not alter the configuration of the Belkin at all (having reset factory defaults beforehand), mainly because although I could access the internet from my PC and my mobile, I could not access the IP address of the router, presumably because the properties of the local area connection on my PC remained unchanged with the IP address (172.168.1.149), Subnet Mask (255.255.255.0), Default Gateway (172.168.1.1) and 3 DNS addresses (172.168.1.1) (10.30.0.1) (8.8.8.8) as they were before hooking up the Belkin. The IP address the mobile received through WIFI on connecting to the Belkin was 172.168.1.148
I was not unduly concerned about not being able to access the configuration of the router as everything was working as I had hoped it would and even when I powered off my PC I still had internet access on my mobile. On rebooting the PC, however, I found that the router changed the DNS addresses on the PC to 2 only, both identical (192.168.2.1) and the IP on the mobile was allocated 192.168.2.2 Although I could still access the internet on my PC, I no longer had access from my mobile although the WIFI connection to the Belkin showed as being 'excellent'. When I did a 'repair' of my internet connection, hoping to revert to a fully operative state, the PC configuration changed again as follows: IP address becomes that of the router (192.168.2.1), Subnet Mask (255.255.255.0), Default Gateway (192.168.2.1), 2 DNS addresses (192.168.2.1) and the IP address allocated to my mobile remains (192.168.2.2) This configuration means I have no internet access from either PC or phone, but CAN access the router configuration. I restored a usable operating state by unplugging the power from the router, transposing the cables in the LAN ports on the router (swapped cable from LAN1 to LAN2 and vice versa), turned off WIFI on mobile and waited a minute or two. When I powered the router back up and switched on mobile WIFI again, everything was restored to the original working state and I have, once again, access to internet on both PC and mobile. It is very frustrating, however, to keep performing this ritual and I wonder if any of you more technically minded, know a way to work around this, perhaps by manually changing the configuration of PC or router?
I am trying to connect a wireless router (EDIMAX br-6228nc) with a ADSL router (NETGEAR). i assigned the LAN IP of the ADSL modem to 192.168.1.1, subnet mask 255.255.255.0, and enable DHCP server.then i connected a LAN port from ADSL router to the WAN port of the wireless router. i assigned IP of the WAN port of wireless router to 192.168.1.10, subnet mask to 255.255.255.0 and default gateway to 192.168.1.1 now on the LAN side of the wireless router i assigned IP 192.168.0.1 and subnet mask 255.255.255.0 enabling DHCP server.on the client pc i selected the setting of automatically assign IP setting (which it got 192.168.0.100, default gateway 192.168.0.1) but my client pc is not able to access the internet.
View 2 Replies View RelatedWe currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
I have bought a WAG320 & ever since I've had it the ADSL line keeps dropping every few hours. The LAN network is fine & I have 7 computers connected to the router wirelessly. When I press the re-set button on the back of the router everything is fine for a few hours then it starts doing it again?
View 9 Replies View RelatedI have been having a weird connection issue for a week or so.The problem is at the first time i boot up my modem it simply cant connect.DSL Line LED keeps blinking- handshaking and training as it says in modem config page.After maybe 5 minutes or 2 hours, totally random.It picks up the connection, i can use it for hours until it randomly drops down once again.Ive contacted my ISP and they came over two times, they state the line quality is not suitable for my connection speed and it will be solved if i drop down my connection speed.Doing that is a painful process cause there is no other speed/quota package suitable for me, so i wanted to ask you people about it before i take action.
My modem is a Dynalink RTA1320 and i tried with another modem, tried mine in a friends house.Plus i went to the place where the cable enters my house and tried over there too, it didnt work as it should pick up in about 20 seconds.Here are stats my modem shows in the config page.[CODE]
The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template
Is there is any reason for ths ? With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting
My Virtual Template config
interface Virtual-Template1
mtu 1440
ip unnumbered Loopback3
[Code].....
Dear The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template.With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting. [code]
View 2 Replies View Related