Cisco Switching/Routing :: 887 Router / 1841 - Dial Up On ADSL Line To New Site
Nov 9, 2012
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
View 7 Replies
ADVERTISEMENT
Jan 19, 2012
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
View 3 Replies
View Related
Aug 24, 2012
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies
View Related
Mar 22, 2011
The PPPoE connection can be successfully established only if the PC dials up, but not if the router replaces the PC to do so.Both the PC and the router are identically configured for this purpose, i.e. using the same ADSL dial-up account(usr/passwd pair). As a whole, we can exclude any wrong configuration on the router itself.
View 3 Replies
View Related
Jan 11, 2011
Now I am tring to setup Cisco 1812j with ISDN Line.
Here is what I connect the device. (I am in Japan)
ISDN Line (NTT east) >> DSU(NTT east INS Mate V30Slim with S/T port) >> Cisco 1812j(S/T)
On DSU setting I enable DSU and Disable Terminator.
First of I would like to test outbound call. Here is the config.
interface BRI0 ip address 192.168.92.2 255.255.255.0 encapsulation ppp dialer map ip 192.168.92.1 name Router1 broadcast 080********(Cell Phone Number) dialer-group 1 isdn switch-type ntt isdn point-to-point-setup ppp authentication chap ppp chap password 0 CISCO ip route 10.92.0.128 255.255.255.248 BRI0 192.168.92.1
Then I test by ping with #debug dialer. #ping 10.92.0.129
And I could not receive a call by my cell phone landline either.
Here is the debug.
[Code]....
View 8 Replies
View Related
Aug 16, 2012
I have a broadband router (Linksys E1000) which I've flashed with a DD-WRT firmware. After doing so I realized that this router doesn't have an interface for ADSL port(RJ-11). How can I use the Linksys E1000 for my home network?
I've heard that I can use ADSL modem(not a router) & plug the RJ-11 to it & take from it the Ethernet & plug it back to the E1000(in the WAN port) would that mean that I can get just a modem and not a hybrid?
Note: Also, I have to mention that my ISP is using PPPoA & DD-WRT is not supporting it, but i googled & they said that the ADSL modem cab be the rescue. Can I pick any ADSL modem for this specific scenario or am I looking at a specific model?
Secondly, can I use my old router to do the job instead of buying a new ADSL modem ? & is it a good approach ? or should i buy a new ADSL modem ?
Update i turned my DD-WRT router(E1000) to act as access point, since this is the only way that i can use it with the DD-WRT feature. & i think this is better than have nothing :) I can now have the DD-WRT functions ;)
View 1 Replies
View Related
Apr 2, 2012
hsrp+bgp+site to site vpn on router 2811.
View 2 Replies
View Related
Dec 26, 2011
I can not get onto the internet via dial up. The message says that I have no dial tone. Using the same line, I get a dial tone on the phone. I can get onto the internet via a DSL connection, but it will not make a connection when I have a telehone line inserted in the phone line jack. This problem started after the power went off and on quickly two times. I have followed all the instructions that I have found to reset the modem, but to no avail. Is it possible that the phone line jack needs to be replaced.I have a gateway laptop with Vista program.
View 4 Replies
View Related
Jan 4, 2011
I'm trying to get a solution together for a dial backup to an ADSL service, using an Analogue modem.The kit list is as follows:
Cisco 877
Multitech MT5656ZDX External Analogue Modem or USR 5630D External Analogue Modem
Rolled patch cable RJ45 to DB25M adapter (pinout from a cisco guide)
So far I am unable to get the router/modem to dial out at all. I know the modems work, I have tested them from Windows.
I have attached a couple of outputs from "show line" and "show line 1" from the router and also what I think are the relevent lines of config although it will be too much config and probably jumbled by now as I've tried quite a few things to try and get this working.
I am more concerned with the config relating to the connection of the analogue modem than the routing element.
View 5 Replies
View Related
Jul 29, 2012
How to configure leased line from the ONT connection on Cisco 1841 router . there have public IPs on the interfaces fa0/0 & fa0/1.
View 4 Replies
View Related
Nov 20, 2011
I can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great
View 1 Replies
View Related
Dec 6, 2012
We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
View 2 Replies
View Related
Oct 25, 2011
I'm installing a new SRP547W for a client and am having trouble setting up a site-to-site vpn. They are using the WAN1 ADSL interface for their internet connection. When I add a sub interface to it I am unable to see the 'Connection Type' drop down like I can see on a WAN2 ethernet sub interface. I have followed the instructions on page 29 provided here: how I can get a a site to site vpn set up on this router using either PPTP or L2TP over the ADSL interface.
View 1 Replies
View Related
Oct 10, 2012
I would like know is that possible to connect two 5505 ASA in site to site VPN with 1 site using ADSL pppoe connection?
View 5 Replies
View Related
Jun 6, 2011
i am trying to setup a hq to 2 remote office vpn connections, all have Cisco 877 ADSL routers.so far to test I tried to setup a site to site vpn between hq and remote 1.
I setup 2 routers with the following settings:
Router 1:
!
!
ip ssh port 3536 rotary 1
ip ssh version 2
!
!
crypto isakmp policy 1
[code]....
View 2 Replies
View Related
Jun 17, 2012
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
View 5 Replies
View Related
Aug 7, 2011
I'm getting a Cisco 1841 router to do a site-to-site VPN. I'd like to know what's the minimum IOS software feature set required for site-to-site VPN?
View 3 Replies
View Related
Jul 23, 2012
I want to implement site to site vpn among our Head Office and Barnch routers (300 Sites).Head Office Site I have a cisco 7200 Router Im going to terminate the VPN conection on that.Branches we are having cisco 1841 series routers. They all are capable of working with VPN.In the present it is act like a EazyVPN Server for selected sites(30 sites).Is there any license limitations in Cisco 7200 Router ?Can I run both Site to site VPN and Eazy VPN Server together ?
View 1 Replies
View Related
Feb 23, 2012
I am try to setup my office network to able to connect to one of my customer HQ via site to site VPN. I am using Cisco 1841 router to do the job.
The problem that I am facing now is no able to connect my other PC in office to the remote site.
show crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
202.x.x.x 175.x.x.x QM_IDLE 1001 ACTIVE(code)
View 9 Replies
View Related
Sep 14, 2011
Have an ADSL router (887) at a site which has a GRE tunnel to to a 3745.The GRE tunnel is setup with default ip mtu of 1476.If I ping from the 3745 to the ADSL router (or in the reverse direction)with a packet size of 1500 bytes this works fine.However if I ping from a router (R1) that is directly connected to 3745 to the ADSL router with a pkt size of1500 bytes then the first ping succeeds while the subsequent pings fail.Pkt sizes less than or equal to 1476 work okay.Pinging between R1 and the 3745 with a packet size of 1500 bytes works fine.If I set the tunnel ip mtu size to 1500 bytes then it works.This is obviously something to do with fragmentation, but I don't undertsand why itdoesn't work with the default mtu set to 1476.
View 11 Replies
View Related
Apr 26, 2013
I have 2 Cisco routers , 1841 and 2811 , I need to setup site to site VPN , but i dont now some how it just does not seems to be working ,
Find attached the Configuration along with the
<----- 172.31.1.0/24----- DG:172.31.1.1>Cisco 2811<Dialer1 -----//Internet//----------Dialer1>Cisco1841---< DG:10.236.5.254-------------- 10.236.5.0/24--->
Find attached command executed on each router in the below order
1) show ver
2) Show run
3) show logging
4) show crypto ipsec sa
5) show crypto isakmp sa
Debugging enabled on routers are
1)Debug Crypto Isakmp
2) Debug Crypto Ipsec.
View 2 Replies
View Related
Jan 28, 2013
The problem I am having is very strange and I have tried to upgrade the IOS on the 1841 to solve the problem but no luck. The issue is when I enable Zone Based firewall security on of the 1841 routers two VPN site-to-site tunnels stops working. If I turn off CEF (no ip cef) then the traffic for both tunnels works. Someone told me that the Zone Based firewall must have a match for the VPN traffic and I created that with ACL 160 and 161 but it did not solve the problem.
Current IOS is below.
Cisco IOS Software, 1841 Software (C1841-ADVSECURITYK9-M), Version 15.0(1)M9, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Sep-12 23:58 by prod_rel_team
[code]....
View 2 Replies
View Related
Nov 20, 2012
i am planning to Configure Site To Site VPN between ASA 5505 & Cisco ADSL Router 887. before going to purchase hardware i want to make sure that site to site vpn will work with these Hardware or not.
View 1 Replies
View Related
Sep 24, 2012
I have recently replaced some Catalyst 3550's with Catalyst 2960s PoE 48 port switches. Since the replacement I have had some issues with phones that will not have a dial tone. They are powered and the network config shows the correct configuration. They have the correct addresses for call manager and the router handling inter-campus calling. We tag the voice vlan separate from data and we use auto qos voip on the switches.
View 5 Replies
View Related
Jul 28, 2012
Using the Cisco Configuration Professional software I have created a site to site VPN connection (between a cisco 1841 and 1811).The tunnel appears to be up as far as the routers are concerned, but I am unable to ping anything on the remote networks. I thought route maps may have had something to do with this but I cant see what is worng with them.Just so you know, the 1841 device already has a functioning VPN tunnel to another site. The peers I am concerned about are 141.0.59.x and 109.238.78.x.
View 12 Replies
View Related
Jul 24, 2012
I am in the process of setting up a site to site VPN connection with a Cisco 1841 with the AIM-VPN-SSL-1 module and an NEC IX2015. We are using a GRE tunnel with IPSec.The problem we are having is the NEC router will not repsond to ICMP packets (and there isn't a way to make it respond). Will this cause any problems with the tunnel?
View 2 Replies
View Related
Nov 8, 2010
We have a fairly major problem with some of our Cisco 877 units (5 in all). All are running 15.2(2)T2 in order to make use of zone-based firewalls and virtual reassembly, and all are exhibiting the same problem. When our ADSL line drops this si shown in syslog
2010-11-09 01:03:06 Local7.Info 192.168.7.1 4733: Nov 9 01:03:05.707: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41799 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident 02010-11-09 01:04:06 Local7.Info 192.168.7.1 4734: Nov 9 01:04:05.946: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41809 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident
[code]...
The "no retrain. sleep 20 seconds" messages continue forever more until somebody power-cycles the router - which is a bit inconvenient as two are 300 miles away. Surprisingly, our event manager applet isn't triggering the reload either, which defeats the object.
View 15 Replies
View Related
Jan 10, 2013
We have 2 router cisco 2621XM and want to configure a VPN between them, but first we want to configure ADSL in both with the card installed.
View 2 Replies
View Related
Dec 5, 2011
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies
View Related
Jul 11, 2012
Is there a guide to set up a site to site VPN using 1841.
I have 3 points, 1 1841, 1 pix 506e and 1 ASA 5500. I need a good guide/manual to set up this. I would like to connect to any of the points, and be able to see all the infrastructure.
View 1 Replies
View Related
Apr 24, 2012
i have 2 routers both 1841's and am trying to get a simple static vpn up and running. Now One router is at our main location (ill call it router a) and the remote location (ill call it router b). Both have internet connectivity that works, can ping router a from b and b to a. Now on router b side when i run show crypto isakmp sa on router b i get the following:
SBOneonta#show crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
72.43.229.138 66.194.51.66 MM_NO_STATE 0 ACTIVE (deleted)
72.43.229.138 66.194.51.66 MM_NO_STATE 0 ACTIVE (deleted)
72.43.229.138 66.194.51.66 MM_NO_STATE 0 ACTIVE (deleted)
[code]....
i72.43.229.138 is the router and the other ip is i have no idea! its no where in the config, but that shows me this router is trying to do something. Now on router a when i run the same command i get this:
show crypto isakmp sa
dst src state conn-id slot status
a whole lot of nothing! now i have been working on this for a few days now and i cant understand why i cant get this simple vpn tunnel to work! I have debuging on both routers, router a shows nothing period for vpn traffic, router b shows a connection from the 66.194.51.66 which again i have no idea who or where this ip is and its not in the config any where.
View 3 Replies
View Related
Oct 18, 2011
I have an 1841 that I set up to do site to site VPN between my company's network and an external network. This has a backup connection point. All works well including automatically failing over to the backup site.
We also want to be able to VPN remotely to our company's network using the same 1841.I have tried many different ways to configure this, but the best I had resulted in an external VPN request taking down the site-to-site link.
Is this possible? Our internet connection is through an ADSL router set up with pasthrough, then into the Cisco 1841 which does the dialer PPPOE authentication.
View 2 Replies
View Related
Oct 9, 2012
ADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.
sh ver
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 31-Jul-07 20:24 by alnguyen
ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes
System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012
System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)
View 1 Replies
View Related
