Cisco Switching/Routing :: Configuring ADSL In Router 2621XM
Jan 10, 2013We have 2 router cisco 2621XM and want to configure a VPN between them, but first we want to configure ADSL in both with the card installed.
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Configuring NAT On 1920 Router With Dual WAN (ADSL)
Jun 7, 2013Basically I have a simple LAN of 30 users and 2 servers that sit on a private address range (192.168.1.1 - 254). I have a Cisco 1921 router with 2 Gigabit Ethnet interfaces and have installed a 2 port Ethernet module to expand interfaces,I have Two Internet providers that provide me an Optic connection to a converter and then a CAT 5 cable. On both of these connections have private public assigned IP addresses.I have a email server and webserver on the LAN (192.168.2 and 192.168.1.3) and with to port forward various ports to these servers - 25, 80, 443 3389, and 2222.
In my external DNS I have two MX records for the mail server (mail.globalhomegroup.com) that point to 2 A records - one record for the publicly assigned IP address of one ISP and another IP address for the other ISP. Ideally what i would like is for mail to be delivered to the first ISP Ip address - the one with the lower MX weighting and then if that line goes down, through the IP address of the second MX record - the backup ISP we are using.
So I guess I am port forwarding to the inetrnal server IP addresses via one of the two external interfaces.At the same time I need to allow internal users to access HTTP, HTTPS etc.So I have managed somehow to configure the external interfaces of the routers to connect to the ISPs and have managed to assign IP info to intenral LAN interface. I can telnet to the router from the Internet via Dialer0 or Dialer1. Other than that I am totally stuck - I have tried to configure and debug NAT etc but cant see wood for the trees now. Basically the port forwarding is not working and i am not sure if the config I have done is in anyway correct.
Cisco Switching/Routing :: Configuring PPPOE ADSL On 887VG
Mar 24, 2013I need to configure configuring pppoe ADSL on cisco 887VG
View 5 Replies View RelatedCisco Switching/Routing :: 2621XM Router 802.1q With VLAN
Jan 27, 2013I have a 2621XM router that I know has reached its end of life. However, would I be able to download the 802.1q VLAN encapsulation for it? If I can, how do I go about doing it.
View 2 Replies View RelatedCisco Switching/Routing :: Recovering From Corrupted Software Router 2621xm?
Jan 14, 2013I am trying to recover a corrupted ios, from rommon after configure all steps of IP_ADDRESS, TFTP_SERVER and so on, copy files correctly, but after it need router 5 minutes to erase flash, or something else....after it i can not boot from ios loaded as i show below:
!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Copying file /c2600-advsecurityk9-mz.123-11.YZ2.bin to flash.
Erasing flash at 0x61fc0000
program flash location 0x60ea0000
[code].....
Cisco Switching/Routing :: How To Setup Dynamic DNS For 2621xm
Sep 10, 2012How to setup dynamic dns for Cisco 2621xm ? What IOS support Dynamic Dns?
View 3 Replies View RelatedCisco Switching/Routing :: Will AIM-COMPR2-V2 Work With 2621xm
Nov 6, 2011will the AIM-COMPR2-V2 will work with the 2621xm
View 1 Replies View RelatedCisco Switching/Routing :: Use 2901 Router With Two ADSL Cards
Dec 5, 2011i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies View RelatedCisco Switching/Routing :: 1700 ADSL Router - Connecting 2 Sites Together
Jan 23, 2012We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
Cisco Switching/Routing :: 887 Router / 1841 - Dial Up On ADSL Line To New Site
Nov 9, 2012I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
Cisco WAN :: Configuring HWIC To ADSL In 1841
May 10, 2011I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies View RelatedCisco Switching/Routing :: Configuring DHCP Pool For Voice Vlan On 2921 Router?
Feb 12, 2013I am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
Cisco WAN :: 2621XM Router Will Not Boot From IOS Image
Nov 27, 2011I've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
Cisco :: Login To 2621XM Router - Cable / Settings
Jun 18, 2011I'm trying to login to my cisco 2621XM router. I'm using putty and I can't remember the how to cable it or the settings to use in putty. I don't have a db9 input on my pc, so I need to go through my NIC. What type of cable to use, what port to plug it into on the router, and what settings to use in Putty.
View 1 Replies View RelatedCisco WAN :: Router Rip And No Shutdown Commands Not Working On 2621xm?
Jun 16, 2012I have an old 2621xm router in CCIE lab at home. Only a week ago I started having issue on 2 of them. The problem is on one of them when I go under interface configuration and I type "no shut" nothing happens. Interface stays in administratively down status and when I check running config "shutdown" is still under interface.
On the other one the same problem but only with "router rip" command. I configure my rip routing but then when I check running config there is no rip section and also RIP is not running under "show ip protocols rip".These routers are connected to 2511 AccesServer. So I thought the issue might be communication from AccessServer to these devices. I connected a console cable straight to them and still the same problem. Everything else is working on these devices.
Cisco Switching/Routing :: Configuring Intervlan Routing Between 2801 And HP Switches?
Aug 5, 2012I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
Cisco Switching/Routing :: SR520 ADSL Connection With PPoE?
Dec 12, 2010I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
View 6 Replies View RelatedCisco Switching/Routing :: Load Balance Between 3 877 ADSL Routers
Apr 25, 2012I have 3 877 ADSL routers for internet connectivity. I recently installed a FW behind them and would like to use the Ciscos as load balance in order to get better utilization from my 3 internet links.
1) the 3 routers are on DHCP from the ISP on the WAN side.
2) the 3 ciscos are on the same class C subnet on the LAN side: 10.201.1.252, 10.201.1.253 and 10.201.1.254
Cisco Switching/Routing :: 887VA / WLAN - Set Up ADSL Connection
Mar 24, 2013to configure this router my main objective is ADSL connection, and wireless network setup.
[code]...
Cisco Switching/Routing :: 881 SDSL With ADSL Backup Configuration?
Feb 26, 2012i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.
View 9 Replies View RelatedCisco Switching/Routing :: ADSL On Fast Ethernet In 1801?
Apr 24, 2012I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
Cisco Switching/Routing :: 1721 With ADSL - Clients Unable To Resolve DNS
Jan 1, 2013I have a Cisco 1721 router with an ADSL wic. I have followed guides on the Cisco website so that I can connect the router to my home adsl connection. The router connects to my broadband provider and sucesfully obtains an IP address along with Dynamically assigned DNS servers. I am able to ping google.co.uk from the router but not from clients attached via DHCP.
I have noticed that if I ping the IP address of google.co.uk from a client it resolves but it will not resolve the name. This would lead me to believe that the problem lies with DNS resolution/forwarding but I do not know how to investigate further.
Cisco Switching/Routing :: 1921 Load Balancing Over 3 ADSL Lines
Aug 22, 2012I have the requirement to provide a Cisco Router with 3 x ADSL lines (768k) to increase the internet speed.PPP multilink is not supported from the ISP.
Is it possbile to distribute the traffic between this three ADSL lines?How can I configure this?
I have the following hardware configuration:
1 x CISCO1921-SEC/K9
2 x EHWIC-VA-DSL-B
The third ADSL line is connected over an ADSL modem at one fixed Router Gigabit interface.
Cisco Switching/Routing :: 877W ADSL Line Interface Not Initializing?
Jan 19, 2012Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
Cisco Switching/Routing :: 2800 Series - Dual ADSL Links?
Jan 31, 2012In a site we currently have 1 BT provided ADSL link which is currently terminated using their device which I believe is some kind of 2wire device, which is extremely slow due to distance from the Exchange (4Mbps)...We have a growing number of users here and want to install a second ADSL line from BT to give them increased performance.
We have a Cisco 2800 sat not doing much so I was wondering if I could use this to load balance the link? I know BT do not support MPPP so therefore the maximum any user can get will be the speed of a single link (4Mbps)...But basically how can this be done..
Can I leave the two BT routers in place and place the Cisco 2800 behind them, or do I need to purchase two ADSL modules for the 2800 and terminate the connection there?Also once done, what do I need to do regarding actually setting up the load balancing? I have seen this:
[URL]
But am unsure as to how relevant it is? I am not sure I understand what the ACL's are being used for? I just want all users on the LAN to load balance out...
Also I am unsure of this statement:You potentially need to add policy-based routing for specific traffic to ensure that it always uses one ISP connection. Examples of traffic that require this behavior include IPSec VPN clients, VoIP handsets, and any other traffic that use only one of the ISP-connection options to prefer the same IP address, higher speed, or lower latency on the connection.I do not understand why a established session such as a VPN client, would ever traverse the second ISP connection anyway?
Cisco Switching/Routing :: Configuring PBR On 300 Series
Jun 1, 2013Configuring an application using routing mode on cisco ace clients ---asa--3750--cisco ace--- servers behind vip,visa card transaction servers.i am able to setup a vip on ace using routing mode on ACE,as the servers need to see the client ip ,so we are not performing SNAT,this part is working fine,when a request comes from the client ,it goes to the vip and to one of the backend servers ,and the request will be forwaded back to the ace ,as the default gateway on the servers is pointing to the server vlan on ace.but if the transaction from the servers need to go to the visa card transaction servers ,how can we achieve this ,and after fetching the data from visa servers,does the reply will be fwd to the ACE or ASAs directly.
View 1 Replies View RelatedCisco Switching/Routing :: 891 - Configuring FTP On Port 990?
May 25, 2012I currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 10 Replies View RelatedCisco Switching/Routing :: Configuring Qos In 2960?
Feb 21, 2013I have IP phones connected to 2960 i want to segregate traffic traffic comming from IP phones which has a COS value of 5 and want to allocate a band width of 200 MBPS for those traffic .
Can any one share sample QOS configuration for achiving this in 2960 ?
Cisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?
Aug 24, 2012i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedCisco Switching/Routing :: Configuring ACE-4710 With Tacacs 3.1?
Jun 10, 2013We think we have configured the ACE and Tacacs properly as we auth, but are not able to enter into configuration mode.
ACE-4710 A4(2.3)
Cisco Switching/Routing :: 6500 - Configuring VSS With Two Sup2T?
Aug 4, 2012I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active
View 6 Replies View RelatedCisco Switching/Routing :: Configuring VPC On The Nexus 3048
May 22, 2013I'm looking for some input on configuring vPC on the Nexus 3048.I know that it's supported to use 1G interfaces for the vPC Peer-Link, but using 2x1G for the Peer-Link would make the Peer-Link a bottle-neck if the 10G ports are used in a vPC. What about using 2x10G ports for the Peer-Link and using the remaining 10G ports in one, or potentially two vPCs. Should that work or is it in any way not recommended? The reason I'm asking is that the 10G ports are called "Uplink" ports in the data sheets for the 3048.
We are planning to connect some servers to the 3048s using vPC with each server connected by 4x1G interface (2x1G for each switch), and then we want to connect a Netapp storage system with two controllers using 2x10G each (the controllers are active/passive, so you can think of it as two separate systems). We would connect controller A with vPC 1x10G to each switch, and controller B in the same way with vPC 1x10G to each switch.
Cisco Switching/Routing :: EtherChannel - Configuring On 4500?
Feb 28, 2012I am about to configure 4 Gig ports for EtherChannel. I've been reading about EtherChannel and it seems easy enough to configure. I have a host (server)which I am going to connect to these 4 - gig ports. This is new for me and would like some feedback for those that have used EtherChannel on their layer 2 switches. The gig ports will be an access port with VLAN XX.
View 6 Replies View Related