Cisco Switching/Routing :: Configuring PPPOE ADSL On 887VG
Mar 24, 2013I need to configure configuring pppoe ADSL on cisco 887VG
View 5 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Configuring ADSL In Router 2621XM
Jan 10, 2013We have 2 router cisco 2621XM and want to configure a VPN between them, but first we want to configure ADSL in both with the card installed.
View 2 Replies View RelatedCisco Switching/Routing :: Configuring NAT On 1920 Router With Dual WAN (ADSL)
Jun 7, 2013Basically I have a simple LAN of 30 users and 2 servers that sit on a private address range (192.168.1.1 - 254). I have a Cisco 1921 router with 2 Gigabit Ethnet interfaces and have installed a 2 port Ethernet module to expand interfaces,I have Two Internet providers that provide me an Optic connection to a converter and then a CAT 5 cable. On both of these connections have private public assigned IP addresses.I have a email server and webserver on the LAN (192.168.2 and 192.168.1.3) and with to port forward various ports to these servers - 25, 80, 443 3389, and 2222.
In my external DNS I have two MX records for the mail server (mail.globalhomegroup.com) that point to 2 A records - one record for the publicly assigned IP address of one ISP and another IP address for the other ISP. Ideally what i would like is for mail to be delivered to the first ISP Ip address - the one with the lower MX weighting and then if that line goes down, through the IP address of the second MX record - the backup ISP we are using.
So I guess I am port forwarding to the inetrnal server IP addresses via one of the two external interfaces.At the same time I need to allow internal users to access HTTP, HTTPS etc.So I have managed somehow to configure the external interfaces of the routers to connect to the ISPs and have managed to assign IP info to intenral LAN interface. I can telnet to the router from the Internet via Dialer0 or Dialer1. Other than that I am totally stuck - I have tried to configure and debug NAT etc but cant see wood for the trees now. Basically the port forwarding is not working and i am not sure if the config I have done is in anyway correct.
Cisco WAN :: 2811 Using Sub-interfaces And PPPOE On ADSL
Apr 26, 2013I am trying to get my Cisco 2811 to authenticate four DSL connections and load balance them by attaching the four DSL to a switch (each DSL going to a seperate VLAN) and then trunking all four VLAN's to a ethernet interface on the 2811. My issue, I can not get more than one DSL to authenticate at a time, for example Dialer1 will connect and then it will disconnect and Dialer2 will connect, etc... I have the modems in bridge mode and I am using seperate user/pass for each DSL account and I have verified that the user/pass are correct.
Below is my config from the router and a couple of messages that came across the console.
*Apr 27 01:12:11.915: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di1
*Apr 27 01:12:11.927: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down
[Code].....
Cisco WAN :: 1941 Router With PPPoE ADSL Conflict
May 3, 2013I m getting the below debug log and can not get IP from my ISP. It is static IP address and there is modem in bridge mode for the adsl line.
Below Conf and debug out put,interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
end
[Code]....
Cisco WAN :: Configuring 851 With PPPoE And DHCP
Aug 29, 2011Trying to find a way to configure my 851 for home use. My internet provider use PPPoE with PAP and althrough I found many configuration options they all are incomplete...or i cant find the logic behind those commands. First of all I need to say what I need:
1. Configurate my int Fa4 (WAN) with pppoe so when i insert my ISP cable in it it will negotiate and take IP.
2. Configurate DHCP on LAN (Fa0-3) so that when I insert my PC it will take a fake IP.
Here is the place where i found some conf examples: [URL] and I have some questions:
1. MTU - Should I use the 1492 value or the "pppoe-client ppp-max-payload 1500"?
2. ip route 10.10.25.2 255.255.255.255 dialer 0 - How can i set an IP route when my connexion informations only come after i connect? (Because is PPPoE)?
3. I cant configurate the DHCP because I dont know the default route, I dont know the DNS, and i dont know the default gateway because I dont know them due to PPPoE !
Cisco WAN :: 887VA ADSL Over Pots Router And PPPoE With Dynamic IP?
Feb 11, 2012I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.I'm trying to setup PPPoE with dynamic IP Followed CISCO's documentations but the commands used were not recognized by the router.
here's my config.
!
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
Cisco WAN :: Configuring 1801 Router For PPPoE?
Jul 16, 2012we have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
Encapsulation: PPPoE
Multiplexing: LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP: dynamically from ISP
configuring cisco router 1801 for above configuration.
Cisco WAN :: Configuring 2900 Router For PPPoE?
Sep 6, 2012I have DSL 8Mbps DL and 768kbps UL The setup look like this:Internet -> Modem -> Cisco Router -> Firewall -> Switch Core - > Multiple switches like sfe2000p? CiscoRouter: i use port gig0/1 for PPPoE and i use port gig0/2 for LAN static Router port gig0/2 with 122.54.144.153/29 connected directly to Firewall port13 with 122.54.144.154/29 ?i want 122.54.144.153/29 will my default gateway ? include no limit bandwidth,filter etc at router, Firewall will be DHCP Server and control the bandwidth, filtering etc and the client computer should get 8Mbps
Mode: Routing
Encapsulation: PPPoE
Username: xx
Password: xx
Service Name: ISP name
[code]....
Cisco Routers :: SRP527W Act As L2TP Tunnel Initiator Over ADSL PPPoE Interface
Jan 29, 2013We are using SRP527 routers with PPPoE ADSL connections. From the SRP527 we create an IPSec tunnel to our core routers (Cisco ASR). We are wanting to change the IPSec tunnels to L2TP, and I need to know if this can be done from the SRP527. I cannot find any L2TP configuration options in the setup options.Can the SRP527W act as an L2TP tunnel initiator over the ADSL PPPoE interface?
View 1 Replies View RelatedCisco WAN :: 887va / Configuring PPPoE Client (external Modem)?
May 15, 2013I've struggled now for a couple of days to setup a PPPoe connection on our cisco 887va box. I can setup straight away on a draytek box so i know the connection is good.I can't get the line protocol to come up? It's connected via ethernet port 0 to an external modem. One thing i can't figure out is if ethernet 0 and fast ethernet 0 is the same physical port?I've attached the running-config below.
Building configuration...
Current configuration : 3738 bytes!! Last configuration change at 16:16:56 UTC Thu May 16 2013version 15.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname **!boot-start-markerboot-end-marker!!no logging bufferedno logging consoleenable secret *************
enable password ***********!no aaa new-modelmemory-size iomem 10!crypto pki trustpoint TP-self-signed-15463827enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-15463827revocation-check nonersakeypair TP-self-signed-15463827!!crypto pki certificate chain TP-self-signed-15463827certificate self-signed 01 **** quit!!!!!!ip cefno ipv6 cef!!license udi pid ***************!!username ************** privilege 15 password 0 *****************!!!!!controller VDSL 0operating mode vdsl2!csdb tcp synwait-time 30csdb tcp idle-time 3600csdb tcp finwait-time 5csdb tcp reassembly max-memory 1024csdb tcp reassembly max-queue-length 16csdb udp idle-time 30csdb icmp idle-time 10csdb session max-session 65535!!!!!!!!!interface Ethernet0description
[code]....
Cisco WAN :: Configuring HWIC To ADSL In 1841
May 10, 2011I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies View RelatedCisco Switching/Routing :: 890C-W Cannot Route With PPPoe?
Apr 2, 2013I have a cisco 890c-w with routing and wireless，contain 8 switch ports（fastethernet 0 - 7），one 100m route port（ fastethernnet 8），one giga port gigagethernet 0
configuration pppoe，dialer1 can get WAN IP。
0-7 ports in vlan2，vlan2 config ip add 192.168.1.1
In router，ping 8.8.8.8 is ok，but ping 8.8.8.8 source 192.168.1.1 can not ok，so my pc can not go internet through 0-7 ports。
I think routing problem，but don't find reason
service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot system flash c890-universalk9-mz.151-4.M2.binwarm-rebootboot-end-marker!!enable password password!no aaa new-model!memory-size iomem 15service-module wlan-ap 0 bootimage autonomouscrypto pki token default removal timeout 0! ip source-route!ip cefip name-server 61.234.145.102ip multicast-routing no ipv6 cef!multilink bundle-name authenticatedvpdn enable!vpdn-group PPPoE!license udi pid CISCO892C-
[code]....
Cisco VPN :: 5505 Site-to-site Vpn With ADSL PPPoE Connection
Oct 10, 2012I would like know is that possible to connect two 5505 ASA in site to site VPN with 1 site using ADSL pppoe connection?
View 5 Replies View RelatedCisco Switching/Routing :: Configure PPPoE On 831 Router With Modem In Bridge Mode
Sep 7, 2012config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Configuring Intervlan Routing Between 2801 And HP Switches?
Aug 5, 2012I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
Cisco Switching/Routing :: SR520 ADSL Connection With PPoE?
Dec 12, 2010I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
View 6 Replies View RelatedCisco Switching/Routing :: Load Balance Between 3 877 ADSL Routers
Apr 25, 2012I have 3 877 ADSL routers for internet connectivity. I recently installed a FW behind them and would like to use the Ciscos as load balance in order to get better utilization from my 3 internet links.
1) the 3 routers are on DHCP from the ISP on the WAN side.
2) the 3 ciscos are on the same class C subnet on the LAN side: 10.201.1.252, 10.201.1.253 and 10.201.1.254
Cisco Switching/Routing :: 887VA / WLAN - Set Up ADSL Connection
Mar 24, 2013to configure this router my main objective is ADSL connection, and wireless network setup.
[code]...
Cisco Switching/Routing :: 881 SDSL With ADSL Backup Configuration?
Feb 26, 2012i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.
View 9 Replies View RelatedCisco Switching/Routing :: ADSL On Fast Ethernet In 1801?
Apr 24, 2012I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
Cisco Switching/Routing :: Use 2901 Router With Two ADSL Cards
Dec 5, 2011i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies View RelatedCisco Switching/Routing :: 1721 With ADSL - Clients Unable To Resolve DNS
Jan 1, 2013I have a Cisco 1721 router with an ADSL wic. I have followed guides on the Cisco website so that I can connect the router to my home adsl connection. The router connects to my broadband provider and sucesfully obtains an IP address along with Dynamically assigned DNS servers. I am able to ping google.co.uk from the router but not from clients attached via DHCP.
I have noticed that if I ping the IP address of google.co.uk from a client it resolves but it will not resolve the name. This would lead me to believe that the problem lies with DNS resolution/forwarding but I do not know how to investigate further.
Cisco Switching/Routing :: 1921 Load Balancing Over 3 ADSL Lines
Aug 22, 2012I have the requirement to provide a Cisco Router with 3 x ADSL lines (768k) to increase the internet speed.PPP multilink is not supported from the ISP.
Is it possbile to distribute the traffic between this three ADSL lines?How can I configure this?
I have the following hardware configuration:
1 x CISCO1921-SEC/K9
2 x EHWIC-VA-DSL-B
The third ADSL line is connected over an ADSL modem at one fixed Router Gigabit interface.
Cisco Switching/Routing :: 877W ADSL Line Interface Not Initializing?
Jan 19, 2012Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
Cisco Switching/Routing :: 1700 ADSL Router - Connecting 2 Sites Together
Jan 23, 2012We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
Cisco Switching/Routing :: 2800 Series - Dual ADSL Links?
Jan 31, 2012In a site we currently have 1 BT provided ADSL link which is currently terminated using their device which I believe is some kind of 2wire device, which is extremely slow due to distance from the Exchange (4Mbps)...We have a growing number of users here and want to install a second ADSL line from BT to give them increased performance.
We have a Cisco 2800 sat not doing much so I was wondering if I could use this to load balance the link? I know BT do not support MPPP so therefore the maximum any user can get will be the speed of a single link (4Mbps)...But basically how can this be done..
Can I leave the two BT routers in place and place the Cisco 2800 behind them, or do I need to purchase two ADSL modules for the 2800 and terminate the connection there?Also once done, what do I need to do regarding actually setting up the load balancing? I have seen this:
[URL]
But am unsure as to how relevant it is? I am not sure I understand what the ACL's are being used for? I just want all users on the LAN to load balance out...
Also I am unsure of this statement:You potentially need to add policy-based routing for specific traffic to ensure that it always uses one ISP connection. Examples of traffic that require this behavior include IPSec VPN clients, VoIP handsets, and any other traffic that use only one of the ISP-connection options to prefer the same IP address, higher speed, or lower latency on the connection.I do not understand why a established session such as a VPN client, would ever traverse the second ISP connection anyway?
Cisco Switching/Routing :: Configuring PBR On 300 Series
Jun 1, 2013Configuring an application using routing mode on cisco ace clients ---asa--3750--cisco ace--- servers behind vip,visa card transaction servers.i am able to setup a vip on ace using routing mode on ACE,as the servers need to see the client ip ,so we are not performing SNAT,this part is working fine,when a request comes from the client ,it goes to the vip and to one of the backend servers ,and the request will be forwaded back to the ace ,as the default gateway on the servers is pointing to the server vlan on ace.but if the transaction from the servers need to go to the visa card transaction servers ,how can we achieve this ,and after fetching the data from visa servers,does the reply will be fwd to the ACE or ASAs directly.
View 1 Replies View RelatedCisco Switching/Routing :: 891 - Configuring FTP On Port 990?
May 25, 2012I currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 10 Replies View RelatedCisco Switching/Routing :: Configuring Qos In 2960?
Feb 21, 2013I have IP phones connected to 2960 i want to segregate traffic traffic comming from IP phones which has a COS value of 5 and want to allocate a band width of 200 MBPS for those traffic .
Can any one share sample QOS configuration for achiving this in 2960 ?
Cisco Switching/Routing :: 887 Router / 1841 - Dial Up On ADSL Line To New Site
Nov 9, 2012I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
Cisco Switching/Routing :: Configuring ACE-4710 With Tacacs 3.1?
Jun 10, 2013We think we have configured the ACE and Tacacs properly as we auth, but are not able to enter into configuration mode.
ACE-4710 A4(2.3)
Cisco Switching/Routing :: 6500 - Configuring VSS With Two Sup2T?
Aug 4, 2012I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active
View 6 Replies View Related