I have 2960G that in rommon status.I need that the switch work in 0x2102 (regular mode).I don't have a backup to configutratuio in my PC.I do wr before the switch go to rommon (startup config).What to do in order to the switch will be in 0x2102 (regular mode) with the same configuration( before the switch go to rommon)?
I'm trying to configure scp for secure configuration backup. I've configured the SCP server with an account and password but, I keep getting the no such file or directory error
AP-C2R1C5-3750#sh run | b arch archive path scp://mchenry:PASSWORD@172.20.22.229//C:/Program_Files/OpenSSH/Cisco_Configs/Switch_Config username mchenry privilege 15 password 7 XXXXXXXXXXXXXXXXXXXXX ip scp server enable
Error: %scp: /C:/Program_Files/OpenSSH/Cisco_Configs/Switch_ConfigSep-17-16-04-44.172-1: No such file or di
SWITCH#ping 172.20.22.229 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 172.20.22.229, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 33/33/34 ms
Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??
And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
We have a few WAN connecting sites to ISP using BGP. we are looking at getting backup link for 1 site.
We have decide to use an IP WAN ADS L link. we will have 877 and 2800 for each link. from understanding, we have a static routing on IPWAN service. means when both BGP WAN and IP WAN connected to the ISP. ISP will use ADSL as primary ignore the BGP link. so other sites will see a BGP route coming from ISP via the ADSL link for this location.
So we have find a manuel solution, leave ADSL unplugged of power but setup same LAN ip address and connect the cable towards the core switch. when WAN link fail, switch on ADSL. So the static route will advertise to the rest of sites.
just want to know is there any auto solution can disable the ADSL link/ ppp link when the 2800/WAN route is up. and enable the ADSL port when the WAN is down. not sure if HSRP/backup interface/tracking will work? and how?
site office switch - > 2800 - > ISP - > ADSL -> ISP (need this link to be backup and protocol down, so the ISP will not able to connect to this link and advertise as next hop)
Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
Rolled patch cable RJ45 to DB25M adapter (pinout from a cisco guide)
So far I am unable to get the router/modem to dial out at all. I know the modems work, I have tested them from Windows.
I have attached a couple of outputs from "show line" and "show line 1" from the router and also what I think are the relevent lines of config although it will be too much config and probably jumbled by now as I've tried quite a few things to try and get this working.
I am more concerned with the config relating to the connection of the analogue modem than the routing element.
We have a cisco 1941 with line t1 Symmetric, (Also have Cisco 1841 unused, but works) I would like to connect the Cisco 1841 to four Adsl Backup lines in case the T1 or the Main cisco 1941 go down I know a BGP is needed on our ISP site,
How can i connect four Adsl lines to The cisco 1841 (Backup) and make them work in a Load Balancing way.
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
My company uses Cisco 891's in replacement of the 1811 where we would have DBU used via an external modem and a triggered time of 3 minutes after a primary connection failure was identified. In testing the 891 in a Layer 2 failure environment, it is within milliseconds that the v.92 port is engaging after the layer 2 failure. Has anyone been able to get it to attempt at a more than millisecond rate?
Redacted config from router: ip sla 1 icmp-echo <%= probeIP1 %> source-interface GigabitEthernet0
I am replacing a faulty sup720 on a 6513. It s the backup/hot not the active sup. It has the same IOS on it. Is it correct that all I need to do is remove the faulty and replace it with the new sup and do a wr mem? Fromwat I have read their should be no down time all connectivity should remain stable?
my 2970 having intermittent problem. i would like to swap with my backup switch WS-2950T. when i try to configure the 2950 following the 2970 config, i unable to perform this command "switchport trunk encapsulation dot1q". does 2950T does not support this command??
I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief Interface IP-Address OK? Method Status Protocol FastEthernet0 unassigned YES DHCP up up BRI0 unassigned YES unset administratively down down BRI0:1 unassigned YES unset administratively down down BRI0:2 unassigned YES unset administratively down down
Just purchased a SG300-52 and am trying to upgrade the firmware to 1.1.2 but cannot get the Upgrade/Backup Firmware Language page to load in the web browser interface. I have tried IE 8 and 9, Firefox 3.16 and 10.02, and Chrome from Windows 7 and XP Pro systems also tried FF and Chrome from Ubuntu system. The page just never loads - doesn't show anything.The same is true of the Download/Backup/Configuration/Log page. The other links under Administration > File Management seem to work fine.
how to configure a backup route to the internet. My client has 2 ISP and basically they want to use 1 ISP and in case the ISP fails, use the other one as backup route to the internet.
The problem I’m facing is that each ISP is plugged to a dedicated ASA 5510, so 1 ISP in one firewall and 1 in the other. Both ASA are plugged to an internal network in a dedicated VLAN with a L3 switch and that L3 switch manages the internal network.
My question is, how can I tell my switch to use ASA1 to go out to the internet and in case the ASA 1 OR THE LINK TO INTERNET used by ASA 1 fails, use ASA 2? It would be great if I can send traffic to the internet thru both connections at the same time. Also, I know the ASA has High Availability configuration, but that applies only if both licenses in the devices are the same and I have a mismatch with the SVPN license, and also I don't know if with my current topology I can use the High Availability model, so I think I can’t use that option and the solution must be applied in the L3 switch, but I don’t know how to tell it to use ASA1 and if failure of the device or the outside interface plugged to ISP 1, then use ASA2. Besides, I would like to know how to optimize this config to do the switch between internet connections seamless to the users if possible (there are VoIP calls on this floor, so I don't want to drop the calls).
use PAGP as backup for wireless link with another wireless link.
__WiFi________ PC-------Switch 1 Switch2---------- PC __WiFi________
We are using 2960 series and from this reason we cant use L3 PAGP I dont know how is PAGP working. If it is checkung port status (UP/Down) or there are some specific L2 packet between etherchannel ports in group?