Cisco Switching/Routing :: AP-C2R1C5-3750 / Configure Scp For Secure Configuration Backup
Sep 16, 2012
I'm trying to configure scp for secure configuration backup. I've configured the SCP server with an account and password but, I keep getting the no such file or directory error
AP-C2R1C5-3750#sh run | b arch archive path scp://mchenry:PASSWORD@172.20.22.229//C:/Program_Files/OpenSSH/Cisco_Configs/Switch_Config
username mchenry privilege 15 password 7 XXXXXXXXXXXXXXXXXXXXX
ip scp server enable
Error: %scp: /C:/Program_Files/OpenSSH/Cisco_Configs/Switch_ConfigSep-17-16-04-44.172-1: No such file or di
SWITCH#ping 172.20.22.229 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 172.20.22.229, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 33/33/34 ms
View 1 Replies
ADVERTISEMENT
Nov 14, 2011
3750 switch connects to Blade-switch_1 and Blade-switch_2 Spanning-tree mode is configured as rapid-pvst on 3750 switch, do I need to configure rapid-pvst on both blade-switches or keep the default pvst config.3750 is running VTP domain HQ and transparent mode Both Blade_switches are running VTP domain CLI and transparent mode To configure Etherchannel between 3750 and blade-switch_1 do I need to have all devices in same vtp domain?
View 16 Replies
View Related
Feb 20, 2012
i have a catalyst 3750, in this switch i have 3 vlan, i need to secure trafic between vlans but im confused ,should i use ACL or VACL to secure ?which is the best ?if i use ACL to secure and limit ports between vlan, which is the best practice to apply the acl ( on th inside or outside of interface)
View 2 Replies
View Related
Mar 15, 2012
how to backup the configuration of ACS 5.3 then restore it on the secondary ACS 5.3 Appliance in order to save time without configure the 2nd Appliance?
View 1 Replies
View Related
Dec 30, 2011
I have 2960G that in rommon status.I need that the switch work in 0x2102 (regular mode).I don't have a backup to configutratuio in my PC.I do wr before the switch go to rommon (startup config).What to do in order to the switch will be in 0x2102 (regular mode) with the same configuration( before the switch go to rommon)?
View 1 Replies
View Related
Feb 26, 2012
i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.
View 9 Replies
View Related
Jul 24, 2012
how to configure a backup route to the internet. My client has 2 ISP and basically they want to use 1 ISP and in case the ISP fails, use the other one as backup route to the internet.
The problem I’m facing is that each ISP is plugged to a dedicated ASA 5510, so 1 ISP in one firewall and 1 in the other. Both ASA are plugged to an internal network in a dedicated VLAN with a L3 switch and that L3 switch manages the internal network.
My question is, how can I tell my switch to use ASA1 to go out to the internet and in case the ASA 1 OR THE LINK TO INTERNET used by ASA 1 fails, use ASA 2? It would be great if I can send traffic to the internet thru both connections at the same time. Also, I know the ASA has High Availability configuration, but that applies only if both licenses in the devices are the same and I have a mismatch with the SVPN license, and also I don't know if with my current topology I can use the High Availability model, so I think I can’t use that option and the solution must be applied in the L3 switch, but I don’t know how to tell it to use ASA1 and if failure of the device or the outside interface plugged to ISP 1, then use ASA2. Besides, I would like to know how to optimize this config to do the switch between internet connections seamless to the users if possible (there are VoIP calls on this floor, so I don't want to drop the calls).
View 5 Replies
View Related
Jan 18, 2011
I have two 3750 switch.switch A(main) and switch B is connected by OFC but i have another wireless link for backup.Now if OFC goes down then i manually connect wireless link with switch B for this reasons i am faceing a lot of problem. I want without any changing of cable if my primary link goes down then my backup link automaticaly goes up and vice versa .
Switch-A port gi1/0/9 and Switch-B port gi1/0/9 is connect by OFC Switch-A port gi1/0/8 and Switch-B port gi1/0/8 is connect by Wireless link (backup) i attach my network diagram kindly find the attachment file.
View 3 Replies
View Related
Apr 16, 2013
I thought I saw a post/question in regards to "how to" configure a Broadband backup for a MPLS circuit.. What I am trying to do is use a cable/dsl/ broadband (secondary) connection as a backup to a MPLS circuit (primary). I have EIGRP and BGP configured on both the branch endpoint and the tunnel headend. The tunnel is used by the interface that connects to the secondary circuit. The branch location router is a 1841 and the "headend" tunnel router is a 3825. I am wondering about the configuration/syntax of a "weight" or static route that can be used to have data flow over the tunnel when the MPLS circuit goes down - and then switch back to the MPLS circuit when it comes back on line.
View 1 Replies
View Related
Jan 28, 2013
In our datacenter we have a 3750 stack with IP base image. I have enabled PBR and reloaded the switch. Show sdm prefer says i am using default template. The reason i want to use PBR is that we have 2 firewalls on the same work and want to be able to have granular control over which gateway out of the network they use but still be able to access all internal resouces accross wan and locally.
Created access list to identify traffic:
access-list 10 permit 10.2.3.59 (test workstation on vlan 3)
Created policy:
route-map TestASA permit 10
match ip address 10
set ip next-hop 10.2.0.3
Assigned policy to the user vlan3:
ip policy route-map TestASA
Results:It changed the default gateway to the above gateway but i could not access any resources on any other vlan, could not access resouces accross wan.
View 16 Replies
View Related
Mar 19, 2012
i have linksys modem which already running for differents vlans i cerated another different vlans 10 amd 20 for 10 and 20 i need internet how should i configure internet on another core switch3750
View 0 Replies
View Related
Nov 7, 2011
configure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
Jan 28, 2012
We have a few stacked 3750 switches with vtp transparent configured...some plugged in a fiber from another network into our stacked switches...that network/switch has vtp server configured...once that switch connected to our stack of switches, it turned that stack switch into vtp server...causing the previous vlans configured to erase thus causing management issues with the stacked switches..
View 4 Replies
View Related
Feb 17, 2013
seeking for configuration assitance on etherchannel between catalyst 3750 and 6506
View 3 Replies
View Related
Dec 31, 2011
I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control). I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8 (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.
View 5 Replies
View Related
Jul 3, 2012
I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.
Network Diagram:
switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
[Code]....
View 8 Replies
View Related
Jul 16, 2012
Our servers are hosted at the Main site, site office A access to the Main site for Internet and servers. We are thinking NextG to take over when the link between sites goes down.
To start with, what is the configuration for 3750 at Site A and the Main site:
1) Trunking for both switches
2) Routing
3) the automatic failover configuration for the switch at Site A.
View 1 Replies
View Related
Apr 17, 2012
I am uploading new configurations to my Cisco 3750 stacked switch and noticed that after the load I cannot log back into the switch because my password somehow was changed. After performing password recovery and getting back into the swtch, I noticed the configuration register was 0xF. I have never seen this before. The config-register command does not seem to be supported to change it back to factory default. The switch is on a ship which has several power hits when they switch power from shore to ship power.Can this cause the configuration register to change? What is the best way to change the configuration register?
View 1 Replies
View Related
Jul 26, 2012
I'm fairly new at trying to create isolated network segments on Cisco switches. What I'm trying to do is have multiple isolated paths that originate from my v Sphere infrastructure travel through a layer 2 link, v LAN, up to a MLS, and ultimately out to to the internet through a firewall. Each sub net might ultimately have a number of hosts on it, but I don't think the make up of those hosts will matter here.
My initial thought was creating v LAN tagged port groups on v Switches on my v Sphere infrastructure. Physical connections will go from my ESXi hosts to the 2900 series Cisco switch connected to trunk ports. Both v LANs would be configured on the switch but not assigned to physical ports. The physical connection to the 3750 would also be a trunk port connection from the 2960. The 3750 would have SVI's created that are attached to VRFs that would control route traffic. This might be totally wrong but from what i've read it seems to be going down the correct path I think.
Two part question, is this the best way to go about designing this network? If so I seem to be really struggling with the SVI/VRF part. Every time I create an SVI all of my hosts on the 10.10.10.x network can ping them, regardless of which v LAN they're on.
I just cannot seem to isolate the 172 network.
View 3 Replies
View Related
May 23, 2012
I'm trying to configure a mirror port on a 3750. This configuration needs to replicate data from local ports, but I need that also act as a regular access port.
With the initial configuration, SPAN port, there is no problem, all the data of the configurated ports is replicating in the configurated port. On the port configurated as mirror there is a PC connected for audio recording. When the port is not operating as SPAN there is communications without problem over the LAN. But when I configure the port as SPAN, communication is interrupted.
Here is the actual configuration:
SWITCH1-PISO7#sh monitor session 1
Session 1
---------
Type : Local Session
[Code]......
View 5 Replies
View Related
Jun 25, 2012
I have 3750 series with GIBICs ports I want to create 10 vlans with its sub-net and enable all vlans to access internet.
View 4 Replies
View Related
Nov 30, 2011
I have WS-C3750-48PS-S, i wanted to implement GLBP on this switch, Is it possible to configure GLBP on this switch?
IOS : c3750-ipservicesk9-mz.122-55.SE4.bin
Part number: WS-C3750-48PS-S
[Code].....
View 4 Replies
View Related
Apr 9, 2013
How to configure hsrp in my client location.They have 1 no of router and 2 no of 3750 switch.they need to configure Hsrp in switch.
View 5 Replies
View Related
Dec 20, 2012
My architecture is the same as show on the link with some difference.I use the router 1841 for inetrnet connexion instead of 7200VXR, this router 1841 is connected on the catalyst 3750 port G1/0/1.I use catalyst 2960 instead of catalyst 2950 or 2948.I use ASA 5510 for conexion on remote branche(I have 5 remote site), This ASA is connected on the catalyst 3750 port G1/0/37
Result of the test:
-I can ping devices in the same Vlans
-I can ping devices in different VLANs
-I can ping all device from the catalyst 3750
I cannot ping the router 1841 or ASA 5510 from the any devices (computer)The gateway of each computer is the correpondant VLAN IP address configured on the catalyst 3750.Why I cannot ping the router 1841 or ASA 5510 from the any devices (computer)
View 19 Replies
View Related
Apr 3, 2013
1. How I can manage those devices, the Switch and the router? What is the BEST SOLUTION to manage this devices?
2. I want to monitor the traffic on this environment, how I can do it? How I can monitor the traffic from customer A, Customer B, and my own LAN traffic, in terms of bandwidth that has passed throught my devices? Is it possible to monitor on MY LAN, or I have to monitor from the EXTERNAL switch?
3. How I can limit the bandwidth? I was trying to configure it using access list, with policy-map, etc....and limit this on each interface. [code]
The interface does not support the specified policy configuration and/or parameter values.Assigning a policy map to the output side of an interface not supported.With I few reading, I could see that the SWITCH 3750 doesnt support this configs.My INTERNET LINK is 30 Mbps, the ports on the Switch (WS-C3750X-48P-L) are Gigabit Ethernet.How I can limit the bandwidth here? For example, How I can limit a interface to 3Mbps..I was thinking about this:
- Limit the interface to 10Mbps: speed 10
- and limit the interface with 30% of this speed: srr-queue bandwidth limit 30
Does this work for both UPLOAD and DOWNLOAD?When the packets passes that 3Mbps limitation, will they be droped?
View 28 Replies
View Related
Feb 5, 2012
I'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
View 6 Replies
View Related
Jan 12, 2012
how to configure this. I did it in the past but kind of forgot how I did it.I have a stacked 3750 (two physical switches) connecting to a 2960.
I am creating trunk ports with limited access to VLAN 300, 600, and 700.
There is two interfaces connected from the 3750's(one on each physical stack member) to the 2960.I have the physical interfaces configured exactly the same.
3750 Config:
interface Port-channel2
!
interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1, 300,600,700
switchport mode trunk
speed 100
[code]....
Should I keep the configuration on the physical ports and not configure the Port-Channel Interfaces? Do I need to configure port-channel load balancing? Is the channel-group mode sufficient? Goal is to basically create 2 links to the 2960 to double the bandwidth and provide redundancy.
View 7 Replies
View Related
Feb 27, 2013
I am building a new network and intended on using the min-link feature on my port-channels between a 3750-X series switch and Nexus 4k.
However reading further into this it seems this feature is only supported on higher end models. I cannot find any reference to the min-links feature in the 3750-X configuration guide. Is this an available feature?
The 3750-X model is WS-C3750X-24T-L running IOS 12.2(55)SE3 IP Services
My thoughts is that the is only an LACP supported feature so I may not see the command until I have entered an LACP specific command on the port-channel but unfortunately I do not have a 3750X to verify this on at present.
View 0 Replies
View Related
Mar 3, 2013
I have one server which run some application for wireless user. this server forward multicast packet to wireless user. server and wlc physically connect to cisco 3750 switch.i want the server forward the multicast packet to wireless users.server access vlan 4.wlc controller have 2 vlan: 90 and 110.and wireless user some of vlan 90 and some of vlan 110.i enable igmp snooping on wireless controller. and enable globally command but it is not working.which additional configuration i need on cisco switch.
Switch(config)# ip igmp snooping
View 16 Replies
View Related
Dec 20, 2012
I have stack of 2 switches 3750?I config etherchannel between them.
here is result
2 Po2(SD) LACP Fa1/0/15(I) Fa2/0/15(I)
Both ports are up up but standalone Int port channel 2 is down down.Need to know if this is default behaviour when we config etherchannel between stack switches?
View 2 Replies
View Related
Mar 6, 2013
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies
View Related
Dec 13, 2011
boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin We have two stack of 3750 switches. When I enter above command getting below mentioned error, two images are showing switch 1, but one image only showing in switch 2, i.e 1st image in show boot command.
%Command to set boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin on switch=2 failed
View 5 Replies
View Related
