Cisco Switching/Routing :: How To Backup The Configuration Of ACS 5.3

Mar 15, 2012

how to backup the configuration of ACS 5.3 then restore it on the secondary ACS 5.3 Appliance in order to save time without configure the 2nd Appliance?

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 2960G Don't Have A Backup To Configuration In PC

Dec 30, 2011

I have 2960G that in rommon status.I need that the switch work in 0x2102 (regular mode).I don't have a backup to configutratuio in my PC.I do wr before the switch go to rommon (startup config).What to do in order to the switch will be in 0x2102 (regular mode) with the same configuration( before the switch go to rommon)?

View 1 Replies View Related

Cisco Switching/Routing :: 881 SDSL With ADSL Backup Configuration?

Feb 26, 2012

i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.

View 9 Replies View Related

Cisco Switching/Routing :: AP-C2R1C5-3750 / Configure Scp For Secure Configuration Backup

Sep 16, 2012

I'm trying to configure scp for secure configuration backup. I've configured the SCP server with an account and password but, I keep getting the no such file or directory error
       
AP-C2R1C5-3750#sh run | b arch archive path scp://mchenry:PASSWORD@172.20.22.229//C:/Program_Files/OpenSSH/Cisco_Configs/Switch_Config
 username mchenry privilege 15 password 7 XXXXXXXXXXXXXXXXXXXXX
 ip scp server enable
  
Error: %scp: /C:/Program_Files/OpenSSH/Cisco_Configs/Switch_ConfigSep-17-16-04-44.172-1: No such file or di
 
SWITCH#ping 172.20.22.229 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 172.20.22.229, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 33/33/34 ms

View 1 Replies View Related

Cisco Switching/Routing :: 2951 - HSRP Backup Taking Two Minutes When Switching Off Primary Router

Oct 7, 2012

I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is  taking 2 mins to take over form primary router. 
 
 [code]....

View 4 Replies View Related

Cisco Switching/Routing :: 891 Using V.92 Port For Backup?

Mar 14, 2012

My company uses Cisco 891's in replacement of the 1811 where we would have DBU used via an external modem and a triggered time of 3 minutes after a primary connection failure was identified.  In testing the 891 in a Layer 2 failure environment, it is within milliseconds that the v.92 port is engaging after the layer 2 failure.  Has anyone been able to get it to attempt at a more than millisecond rate? 
 
Redacted config from router:
ip sla 1
icmp-echo <%= probeIP1 %> source-interface GigabitEthernet0

[Code].....

View 0 Replies View Related

Cisco Switching/Routing :: Replacing A Backup Sup 720 On 6513

Nov 21, 2011

I am replacing a faulty sup720 on a 6513. It s the backup/hot not the active sup. It has the same IOS on it. Is it correct that all I need to do is remove the faulty and replace it with  the new sup and do a wr mem? Fromwat I have read their should be no down time all connectivity should remain stable?

View 6 Replies View Related

Cisco Switching/Routing :: How To Backup VLAN DAT On 6509

Feb 5, 2013

We backup the running config on the 6509 does it also backup the vlan.dat as well?I tried command dir/all and just dir but did not see the vlan.dat listed

View 6 Replies View Related

Cisco Switching/Routing :: Backup And Restore ASA 5505 Config

Dec 21, 2011

I need to backup my ASA 5505 configuration and restore it to default, then I'll configure manually the new config, but if something doesn't work I want to restore the backup made before.
 
I tried the "copy run tftp" command, and it always answers the same: Result of the command: "copy run tftp" [code] I read everywhere its supossed to prompt asking me tftp server address and file name.

View 7 Replies View Related

Cisco Switching/Routing :: Nexus 7k Switches Config Backup

Apr 9, 2013

I have a small doubt with Nexus 7k,5K,2k & 1K.We want to backup the running config to my desktop through tftp.When i tried to backup from Nexus switches showing like below Nexus 7K. [code]

It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config Vdc-all". [code]

It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric"
 
It's showing three choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric" or "copy running-config startup-config vdc-all". [code]

View 11 Replies View Related

Cisco Switching/Routing :: Swap With Backup Switch WS-2950T

Jan 8, 2013

my 2970 having intermittent problem. i would like to swap with my backup switch WS-2950T. when i try to configure the 2950 following the 2970 config, i unable to perform this command "switchport trunk encapsulation dot1q". does 2950T does not support this command??

View 8 Replies View Related

Cisco Switching/Routing :: 6509 Convert CatOS Configuration To Native IOS Configuration

Jul 17, 2012

I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
 
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.

View 1 Replies View Related

Cisco Switching/Routing :: 3750E-1 Meaning Of Backup On HSRP Statas

Oct 25, 2011

What is meaning backup on HSRP statas?There are 5 vlans.The other four vlans aren't backup status.Only one of five vlans display messeages. When I reload Catalyst3750E-1,debug log. [code]

View 6 Replies View Related

Cisco Switching/Routing :: SG300 Upgrade / Backup Page Not Loading?

Feb 28, 2012

Just purchased a SG300-52 and am trying to upgrade the firmware to 1.1.2 but cannot get the Upgrade/Backup Firmware Language page to load in the web browser interface.  I have tried IE 8 and 9, Firefox 3.16 and 10.02, and Chrome from Windows 7 and XP Pro systems also tried FF and Chrome from Ubuntu system.  The page just never loads - doesn't show anything.The same is true of the Download/Backup/Configuration/Log page.  The other links under Administration > File Management seem to work fine.

View 1 Replies View Related

Cisco Switching/Routing :: 5510 How To Configure A Backup Route To Internet

Jul 24, 2012

how to configure a backup route to the internet.  My client has 2 ISP and basically they want to use 1 ISP and in case the ISP fails, use the other one as backup route to the internet.
 
The problem I’m facing is that each ISP is plugged to a dedicated ASA 5510, so 1 ISP in one firewall and 1 in the other.  Both ASA are plugged to an internal network in a dedicated VLAN with a L3 switch and that L3 switch manages the internal network.
 
My question is, how can I tell my switch to use ASA1 to go out to the internet and in case the ASA 1 OR THE LINK TO INTERNET used by ASA 1 fails, use ASA 2?  It would be great if I can send traffic to the internet thru both connections at the same time.  Also, I know the ASA has High Availability configuration, but that applies only if both licenses in the devices are the same and I have a mismatch with the SVPN license, and also I don't know if with my current topology I can use the High Availability model, so I think I can’t use that option and the solution must be applied in the L3 switch, but I don’t know how to tell it to use ASA1 and if failure of the device or the outside interface plugged to ISP 1, then use ASA2.  Besides, I would like to know how to optimize this config to do the switch between internet connections seamless to the users if possible (there are VoIP calls on this floor, so I don't want to drop the calls). 

View 5 Replies View Related

Cisco Switching/Routing :: 2960 - Using PAGP As Backup For Wireless Link With Another One

Jul 7, 2012

use PAGP as backup for wireless link with another wireless link.
 
                             __WiFi________
PC-------Switch 1                              Switch2---------- PC
                            __WiFi________
 
We are using 2960 series and from this reason we cant use L3 PAGP I dont know how is PAGP working. If it is checkung port status (UP/Down) or there are some specific L2 packet between etherchannel ports in group?

View 5 Replies View Related

Cisco Switching/Routing :: Command In 6513 To Take IOS Image Backup And Restore?

Apr 18, 2013

I need to know the command to take the Backup and Restore of IOS Image of 6513 through tftp server.

View 6 Replies View Related

Cisco Switching/Routing :: C3750 - Kron Policy-list Backup

Jun 2, 2008

Have C3750 Version 12.2(25r)SEE3 , Trying to run:

kron policy-list backup
cli write cli copy running-config tftp://xx.xx.xx.xx/swi06-confg
kron occurrence backup at 22:00 Mon recurring
policy-list backup
 
There are nothing backup and nothing in the log.

View 6 Replies View Related

Cisco :: Backup Configuration On LMS 4.2

Nov 21, 2012

1)how can i backup the configuration on cisco lms 4.2 and to re-imported later when i re-install the lms 4.2
  
2)how can i change the admin password on cisco lms 4.2

View 3 Replies View Related

Cisco Switching/Routing :: 1941 - Use One Ethernet Port (G0/0) As Primary And Other (G0/1) As Backup Interface

Jan 20, 2013

Here's my problem.  I'm going to be using Cisco 1941 routers at a bunch of remote sites.  All of these sites have 2 comm paths out.  Some of them have 2 IP/VHF radios and some have 1 IP/VHF radio and a copper link using Patton ethernet extenders.  From the VHF radios the data hit our MPLS network back to our HQ and the sites with copper go directly back to our HQ.  Everything ends up at a Cisco 4948 switch. The problem I'm having is that I want the routers at the remote site to use one ethernet port (G0/0) as the primary and the other (G0/1) as the backup interface.  I've tried the backup interface command but the problem is that depending on where an outage occurs the ethernet link to either the radio or Patton stays up so it never switches over. We're using OSPF as our routing protocol and I'm sure there's something that can be done with it but I'm not sure what. 

View 4 Replies View Related

Cisco Switching/Routing :: 4506e Start-up Config Backup To Tftp Server

Mar 15, 2012

how can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch

View 2 Replies View Related

Cisco Switching/Routing :: 3825 How To Configure A Broadband Backup For MPLS Circuit

Apr 16, 2013

I thought I saw a post/question in regards to "how to" configure a Broadband backup for a MPLS circuit..  What I am trying to do is use a cable/dsl/ broadband (secondary) connection as a backup to a MPLS circuit (primary).  I have EIGRP and BGP configured on both the branch endpoint and the tunnel headend.  The tunnel is used by the interface that connects to the secondary circuit.  The branch location router is a 1841 and the "headend" tunnel router is a 3825.  I am wondering about the configuration/syntax of a "weight" or static route that can be used to have data flow over the tunnel when the MPLS circuit goes down - and then switch back to the MPLS circuit when it comes back on line.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: Backup Configuration On ACS 5.2?

Jun 8, 2012

How to backup the configuration on cisco acs 5.2 and how to restore it , if some thing wrong happened

View 7 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.x / How To Backup Configuration

Mar 10, 2013

Cisco ACS 5.x appliance?How to back up Config?What is best way, via TFTP? COPY Startup-config tftp:?COPY Running-config tftp:?I currently use Solarwinds CatTolls to back my Cisco Switches, can I use this for Cisco ACS also?

View 3 Replies View Related

Cisco :: LMS 4.2 Backup Configuration Of Devices

Nov 29, 2012

How to backup the configuration of Cisco devices managed by LMS 4.2 and store it in Folder , than restore it once it need it

View 10 Replies View Related

Cisco Firewall :: ASA 5505 Backup ISP Configuration

Jun 13, 2011

I'm having problems configuring an asa 8.2(1) with a backup isp.  I followed the asdm instructions in this document: [URL]
 
I have my backup interface configured as DHCP and the static routes set. Pinging the gateway and other external IP address from the backup interfaces works normally. I have also tried configuring the backup interface as a static address but got the same results.
 
When removing the primary wan link, all traffic stops. When I ping a external DNS, I get these errors in the log: portmap translation creation failed for udp src inside: 192.168.13.23 dst backup:208.67.222.222_type 8, code0)
 
I though this type of error is related to a NAT problem, not sure where to look though.

View 4 Replies View Related

Cisco Wireless :: Backup Configuration On WAP 5508?

Feb 5, 2013

how to backup a Cisco Wireless Access Point Controller 5508.

View 2 Replies View Related

Cisco :: Backup Of Configuration From Nexus Switches 5K And 7K

Dec 4, 2012

I'm busy on configuring the backup of the configuration from Nexus switches 5K and 7K.I have installed COPSSH on my windows server and try to confiugre the sftp credentials. [code] I have tested from the CLI from the switch and i have the issue but if i use the default vrf 'default' it works fine.How can i change the command sent by DCNM to the Nexus in order to specify vrf default and not vrf management ?

View 1 Replies View Related

Cisco :: LMS 4.0.1 - Device Configuration Auto Backup

Mar 6, 2012

Is it possible to create a job what automatically export the devices configs that are in the folder CSCOpxfiles medemushadow? It would be wonderdul if CW could export the .cfg files into a .rar and send in email or something like this.

View 1 Replies View Related

Cisco :: 5508 - NCS Configuration Backup And Restore Of WLC

Jan 10, 2012

I recently tested the process for a customer of defaulting a Cisco WLC to factory configuration and then restoring the configuration from Cisco NCS.  It was not seamless to say the least and I wonder if I have just gone about it the wrong way. 
 
Have have set the NCS platform to configuration sync with the 5508 controllers at 04:00 every day and prior to the controller defaulting I ensured that NCS also reported that the config was in sync. I have also set NCS to complete a tftp backup of the controller every night 23:00 - interestingly though I have no idea where this is stored on the NCS platform ( a VM appliance ) or what it's file name is.
 
Anyway my experiences where as follows:-
1.  defaulted WLC and via serial CLI ended up at the configuration wizard.
2.  Set the correct LAG, management IP, host name that NCS knew this controller by.
3.  To test things just created a dummy WLAN ( SSID ) as I assumed this would be overwritten ( big mistake ! ). 
 
At this point I connected the controller to the network and tried to restore the configuration from the config sync version.

First problem - you have to remember to set up the SNMP community string you were using as it is needed by the configuration sync process.  After adding this to the controller I could push the configuration to the controller.

Second problem - failed to add the first WLAN from the backup as I have added the temporary dummy W LAN via the wizard and NCS reported a conflict.  So had to delete WLAN ID 1 from the WLC GUI directly and then the config push no longer reported this error.

Third problem - for some reason did not add the TACACS server details - reported the error that it could not added them.  I manually added these via a template via NCS and all was well. 

Fourth problem - all but the first WLAN was in the disabled state - had to re-enable all of the WLANs. 

Fifth problem - any default items I had disabled or removed have not been saved - therefore I have removed the public and private SNMP communities - but these were still on the WLC after the restore.  I have disabled unused ports not in the LAG as they show an error in NCS - these where not disabled after the restore.
 
So all in all not a very satisfactory restore process from NCS to an defaulted WLC ( meant to simulate to the customer what would be needed if they had to replace a controller due to hardware failure ).

View 1 Replies View Related

Cisco :: User Privilege Level For Configuration Backup With PI 1.2

Feb 15, 2013

We have more than 50 devices handling by PI 1.2 (testing) I like to know how to do configuration archiving with user who doesn't have write privilege.
  
I tried like this.
  
username john privilege 6 password cisco privilege exec level 6 show running-config
  
(result) show run --> blank
 
  I tried this user with one of switch in PI 1.2. It did not do configuration backup
 
username inout password inout username inout privilege 15 autocommand show running-config
  
(result) once logged in, it automatically showed running-config. However when I tried with PI 1.2 with this user (inout). I couldn't do configuration back.
 
reference [URL]
  
create certain user with read-only privilege while PI 1.2 is able to do configuration archiving ?

View 0 Replies View Related

Cisco VPN :: ASA 5505 Backup Configuration To TFTP Server?

Oct 4, 2011

Is there a way to backup the configuration file to a tftp server? I've tried "copy start tftp" and copy run tftp". No luck, I get an error message.

View 1 Replies View Related

Cisco :: LMS 4.2.1 - Backup Configuration Of WS-C4503-E Version Cat4500e

Oct 11, 2012

I have a Cisco LMS 4.2.1 on a Windows 2008 Server R2 platform and I would like to backup the configuration of my WS-C4503-E version cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1I create the job in Configuration > Configuration Archive > Synchronization and after the execution of the job, I check th status in Admin > Job > Browser: I don't know why the archive doesn't exist. It's a newly install.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved