Cisco :: LMS 4.0.1 - Device Configuration Auto Backup

Mar 6, 2012

Is it possible to create a job what automatically export the devices configs that are in the folder CSCOpxfiles medemushadow? It would be wonderdul if CW could export the .cfg files into a .rar and send in email or something like this.

View 1 Replies


ADVERTISEMENT

Cisco :: How To ASR 9k Auto-backup To External FTP Server

Jun 20, 2012

How to take auto  running configuration backup when use commit command in asr9k  .Our asr9k sofware Version 4.0.1[Default] .I usse the commands

ftp client password encrypted 050D121F345F4B1B4
ftp client username cisco
ftp client source-interface GigabitEthernet0/0/0/14
ftp client anonymous-password cisco
(Password information changed)
 
configuration commit auto-save filename ftp://10.10.10.3/ASR9K/asr_conf But auto backup not happening .following errror showing after every COMMIT command.

( Error:Couldn't save file /ftp://10.10.10.3/ASR9k/asr_conf.
Error:'CfgMgr' detected the 'warning' condition 'Operation is temporarily suspended.' )
 
Manually I able to take Running-configuration backup through ftp int same lacation (ftp://10.10.10.3/ASR9K/asr_conf ) .But automatically not happening .

View 1 Replies View Related

Servers :: Auto-Backup Folders And Files?

Sep 18, 2011

How to set auto backup folders and files in windows2003Should i use inbuilt utility or should i use any Third Party software if software which is the best one that i use

View 1 Replies View Related

Sharing :: Use Old Computer As Auto-sync Backup And Production Server?

Jun 20, 2011

I have this idea of using my old computer (which is still pretty awesome) as a back up + production server. What this would entail would be that each person in my house has a dedicated hard drive that auto-syncs folders they've selected for backing up (not Memeo under any circumstances!). Then there will be a hard drive for me to work on web projects on. I'd like this computer to be very secure but if needed, I could show my work on the production drive to my boss.

View 6 Replies View Related

D-Link DIR-655 :: Does Auto Configuration Overrides Manual Configuration

Dec 14, 2012

I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem.  So, out with the paperclip to do the big reset, causing me to lose my configuration.  When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams.  Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP.  I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either.  I tried EVERYTHING.  Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move.  UPnP had always been checked off in the router.  So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?

View 2 Replies View Related

Auto-Configuration IPv4 Does Not Match Up

Feb 29, 2012

I live in a shared house, and I am the only one who has been experiencing issues connecting to the internet. I have to ask a housemate to reset the server, as this is the only thing that works.

When I am unable to connect, and I use command ipconfig, the following appears: Autoconfiguration IPv4 169.254.23.29 On the occasions when I am connected, the following appears in its place: IPv4 IP Address: 192.168.0.2

One tip that I came across was to check the box (Wireless Network properties, Connection tab) for "Connect even if the network is not broadcasting". I had hoped this simple solution would assist, but to no avail.

View 5 Replies View Related

Cisco :: Prime 4.2 Backup Of Device Config

May 21, 2012

We are currently running Cisco prime 4.1 and want to make sure there is a backup of the configurations from our switches and routers. The VLANconfig is not collected according to the devicestatus dashboard. i am aware there were a known issue with LMS running on a virtual server and vlan not being able to be collected, is this issue resolved? i have tried the various workarounds with TAC support and it hasnt worked. We have the running and startup config collected for our devices when looking at the device status dashboard. does this mean if a switch crashes we can restore the config to a new switch immediately?
 
i saw there is a version 4.2. maybe this version resolves the issue with LMS on a virutal server? i cannot find the download to upgrade to 4.2 in the support section though.

View 1 Replies View Related

Configure Safari With Auto-proxy Configuration?

Mar 27, 2013

I configure safari with auto proxy configuration, insert the proxy server name, and click apply.However, if i go to network-tools.com and do a traceroute, the trace does not show the proxy serverin the series of IP address's. I have tried with several different server names but i makes no

View 1 Replies View Related

Auto-configuration IPv4 Address In 169 Range?

Mar 30, 2012

Last two weeks, I have had a problem connecting to public hotspots. My own WiFi network is fine, but while I am connected to any public hotspot I get the 'no internet access' message on the wifi symbol.While connected to my own network, ipconfig/all shows that I have an Autoconfiguration IPv4 address in the (correct) 192 range - but when connected to a hotspot, the address is in the 169 range, or occasionally (as in the instance below) in the 10 range. Clearly this is the problem, but I cannot figure out what has caused it. Is it hardware? Software? Malware? Or user error?I have run the Wireless Test and the log results are pasted below.

Windows IP Configuration

Host Name . . . . . . . . . . . . : XPS-CLIENT-TIM
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

[code]....

View 14 Replies View Related

Good Product To Use To Backup Device Configurations?

Apr 5, 2012

What's a good product to use to backup device configurations?

View 19 Replies View Related

Cisco Switching/Routing :: 4500 Sup6E Auto QoS Configuration On PortChannel

Jun 28, 2012

I configured Auto QoS on some access ports on two 4506-E (Sup 6E-L) and I wanted to apply the same generated config on the port channel/port channel members but it didn't work.
 
Ex:
int gig1/3
service-policy input AutoQos-VoIP-Input-Cos-Policy
% A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port.

[Code].....

View 1 Replies View Related

Cisco WAN :: 1801 Device Repeatedly Calling ISDN Backup Line?

Jan 13, 2009

we have a Cisco 1801 at one of our remote sites that uses an ADSL line for it's primary connection and ISDN as backup. Despite no apparent problems with the ADSL line the ISDN is repeatedly dialling the internet every 2-3 mins during office hours and considerable expense to the customer.

View 3 Replies View Related

Cisco :: Backup Configuration On LMS 4.2

Nov 21, 2012

1)how can i backup the configuration on cisco lms 4.2 and to re-imported later when i re-install the lms 4.2
  
2)how can i change the admin password on cisco lms 4.2

View 3 Replies View Related

Cisco AAA/Identity/Nac :: Backup Configuration On ACS 5.2?

Jun 8, 2012

How to backup the configuration on cisco acs 5.2 and how to restore it , if some thing wrong happened

View 7 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.x / How To Backup Configuration

Mar 10, 2013

Cisco ACS 5.x appliance?How to back up Config?What is best way, via TFTP? COPY Startup-config tftp:?COPY Running-config tftp:?I currently use Solarwinds CatTolls to back my Cisco Switches, can I use this for Cisco ACS also?

View 3 Replies View Related

Cisco :: LMS 4.2 Backup Configuration Of Devices

Nov 29, 2012

How to backup the configuration of Cisco devices managed by LMS 4.2 and store it in Folder , than restore it once it need it

View 10 Replies View Related

Cisco Switching/Routing :: How To Backup The Configuration Of ACS 5.3

Mar 15, 2012

how to backup the configuration of ACS 5.3 then restore it on the secondary ACS 5.3 Appliance in order to save time without configure the 2nd Appliance?

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Backup ISP Configuration

Jun 13, 2011

I'm having problems configuring an asa 8.2(1) with a backup isp.  I followed the asdm instructions in this document: [URL]
 
I have my backup interface configured as DHCP and the static routes set. Pinging the gateway and other external IP address from the backup interfaces works normally. I have also tried configuring the backup interface as a static address but got the same results.
 
When removing the primary wan link, all traffic stops. When I ping a external DNS, I get these errors in the log: portmap translation creation failed for udp src inside: 192.168.13.23 dst backup:208.67.222.222_type 8, code0)
 
I though this type of error is related to a NAT problem, not sure where to look though.

View 4 Replies View Related

Cisco Wireless :: Backup Configuration On WAP 5508?

Feb 5, 2013

how to backup a Cisco Wireless Access Point Controller 5508.

View 2 Replies View Related

Cisco :: Backup Of Configuration From Nexus Switches 5K And 7K

Dec 4, 2012

I'm busy on configuring the backup of the configuration from Nexus switches 5K and 7K.I have installed COPSSH on my windows server and try to confiugre the sftp credentials. [code] I have tested from the CLI from the switch and i have the issue but if i use the default vrf 'default' it works fine.How can i change the command sent by DCNM to the Nexus in order to specify vrf default and not vrf management ?

View 1 Replies View Related

Cisco :: 5508 - NCS Configuration Backup And Restore Of WLC

Jan 10, 2012

I recently tested the process for a customer of defaulting a Cisco WLC to factory configuration and then restoring the configuration from Cisco NCS.  It was not seamless to say the least and I wonder if I have just gone about it the wrong way. 
 
Have have set the NCS platform to configuration sync with the 5508 controllers at 04:00 every day and prior to the controller defaulting I ensured that NCS also reported that the config was in sync. I have also set NCS to complete a tftp backup of the controller every night 23:00 - interestingly though I have no idea where this is stored on the NCS platform ( a VM appliance ) or what it's file name is.
 
Anyway my experiences where as follows:-
1.  defaulted WLC and via serial CLI ended up at the configuration wizard.
2.  Set the correct LAG, management IP, host name that NCS knew this controller by.
3.  To test things just created a dummy WLAN ( SSID ) as I assumed this would be overwritten ( big mistake ! ). 
 
At this point I connected the controller to the network and tried to restore the configuration from the config sync version.

First problem - you have to remember to set up the SNMP community string you were using as it is needed by the configuration sync process.  After adding this to the controller I could push the configuration to the controller.

Second problem - failed to add the first WLAN from the backup as I have added the temporary dummy W LAN via the wizard and NCS reported a conflict.  So had to delete WLAN ID 1 from the WLC GUI directly and then the config push no longer reported this error.

Third problem - for some reason did not add the TACACS server details - reported the error that it could not added them.  I manually added these via a template via NCS and all was well. 

Fourth problem - all but the first WLAN was in the disabled state - had to re-enable all of the WLANs. 

Fifth problem - any default items I had disabled or removed have not been saved - therefore I have removed the public and private SNMP communities - but these were still on the WLC after the restore.  I have disabled unused ports not in the LAG as they show an error in NCS - these where not disabled after the restore.
 
So all in all not a very satisfactory restore process from NCS to an defaulted WLC ( meant to simulate to the customer what would be needed if they had to replace a controller due to hardware failure ).

View 1 Replies View Related

Cisco :: User Privilege Level For Configuration Backup With PI 1.2

Feb 15, 2013

We have more than 50 devices handling by PI 1.2 (testing) I like to know how to do configuration archiving with user who doesn't have write privilege.
  
I tried like this.
  
username john privilege 6 password cisco privilege exec level 6 show running-config
  
(result) show run --> blank
 
  I tried this user with one of switch in PI 1.2. It did not do configuration backup
 
username inout password inout username inout privilege 15 autocommand show running-config
  
(result) once logged in, it automatically showed running-config. However when I tried with PI 1.2 with this user (inout). I couldn't do configuration back.
 
reference [URL]
  
create certain user with read-only privilege while PI 1.2 is able to do configuration archiving ?

View 0 Replies View Related

Cisco VPN :: ASA 5505 Backup Configuration To TFTP Server?

Oct 4, 2011

Is there a way to backup the configuration file to a tftp server? I've tried "copy start tftp" and copy run tftp". No luck, I get an error message.

View 1 Replies View Related

Cisco :: LMS 4.2.1 - Backup Configuration Of WS-C4503-E Version Cat4500e

Oct 11, 2012

I have a Cisco LMS 4.2.1 on a Windows 2008 Server R2 platform and I would like to backup the configuration of my WS-C4503-E version cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1I create the job in Configuration > Configuration Archive > Synchronization and after the execution of the job, I check th status in Admin > Job > Browser: I don't know why the archive doesn't exist. It's a newly install.

View 2 Replies View Related

Cisco Application :: ACE-20 Module - Automated Backup Of Configuration

Feb 4, 2010

I am currently stuck to setup an automated configuration backup for ACE Blades. I found a script to backup the ACE from the Cisco ANM box but unfortunately I am not very familiar with Linux. (script) in place, to "pull" the ACE config from a Microsoft system ?
 
System State:
ACE IOS A2.(1).5

View 2 Replies View Related

Cisco Switching/Routing :: 2960G Don't Have A Backup To Configuration In PC

Dec 30, 2011

I have 2960G that in rommon status.I need that the switch work in 0x2102 (regular mode).I don't have a backup to configutratuio in my PC.I do wr before the switch go to rommon (startup config).What to do in order to the switch will be in 0x2102 (regular mode) with the same configuration( before the switch go to rommon)?

View 1 Replies View Related

Cisco :: 2504 WLC To Trigger Configuration Backup When It Is Saved

Apr 17, 2013

I can't seem to find and answer to this, but is it possible on a 2504 WLC to trigger a configuration backup when the configuration is saved like on Cisco routers and switches?

View 2 Replies View Related

Cisco Firewall :: ASA 5505 - Backup ISP Link Configuration?

Jan 28, 2013

I'm working on setting up a backup link for our ASA 5505 and I've followed these directions:  [URL]
 
The backup ISP gives us a dynamic address, however, when I enable the backup ISP's interface on the ASA, my vpn tunnels drop. As soon as I disable the backup interface, the tunnels come back up. I'm attempting to configure this across one of these tunnels, so obviously this is an issue, as is the fact that other people need the tunnels as well. I'm not sure what I did to make this happen, but I've been over the config many times and can't see anything different from the instructions in the link above.
 
I thought it might be trying to route traffic across the backup interface, but my primary interface is tracked and has SLA running on it, so I would assume it wouldn't roll over onto the backup interface.

View 1 Replies View Related

Cisco Firewall :: ASA 5520 Configuration Backup With Archive?

Nov 15, 2011

On our cisco 3750 switches we can take config backups with the archive command. After every "write mem" it rights the config to our backup server. We would like to do this also for our asa 5520 with version 8.2(2). I also searched in the command reference guide, but I can't seem to find the proper command to do it.

View 2 Replies View Related

Cisco Firewall :: Best Practice For Log Configuration And Backup In ASA5505

Feb 20, 2011

I like to take log backup in ASA.. and i like to check whether any attack pattern is there?? how could i do this...?Also how could i do a best practise for this?

View 12 Replies View Related

Cisco WAN :: 5520 / Backup Internet Link Configuration

Dec 14, 2012

i have two internet links each of which from different ISP and different real ip addresses.Want to make the second backup internet work for Internal and external (AnyConnect) users.
 
my question:  is that applicable to register single A record with different real ip addresses? and also is the AnyConnect method the best solution for them?
 
note: i have single firewall 5520 behind the cable modems.

View 3 Replies View Related

Cisco Application :: ACE 4710 - Context Management / Backup Of Configuration?

Jun 25, 2012

I am looking at management (backup of the configuration) of the ACE 4710 running A4.1, the management software is Cisco Cirrus. The question I have is around the management of the context's, I have a backup of the Admin but would like the user context's also, how this is completed.              

View 3 Replies View Related

Cisco Switching/Routing :: 881 SDSL With ADSL Backup Configuration?

Feb 26, 2012

i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved