Cisco :: Prime 4.2 Backup Of Device Config
May 21, 2012
We are currently running Cisco prime 4.1 and want to make sure there is a backup of the configurations from our switches and routers. The VLANconfig is not collected according to the devicestatus dashboard. i am aware there were a known issue with LMS running on a virtual server and vlan not being able to be collected, is this issue resolved? i have tried the various workarounds with TAC support and it hasnt worked. We have the running and startup config collected for our devices when looking at the device status dashboard. does this mean if a switch crashes we can restore the config to a new switch immediately?
i saw there is a version 4.2. maybe this version resolves the issue with LMS on a virutal server? i cannot find the download to upgrade to 4.2 in the support section though.
View 1 Replies
ADVERTISEMENT
Jan 14, 2013
We have LMS Prime 4.2. I know how to view the running config on a single device. How do I run a report that will pull all the running configs of all my devices in one report? I'd be able to same them as one big pdf or text file. ]
View 1 Replies
View Related
May 26, 2013
I try to create a reposiroty for FTP Backup but it is not working with directories. Isn't it possible to create FTP repositories with directories?
I need to ad this URL e.g.: ftp://server/IT/Wi-Fi/Backup
This is not working. % Error reading directory on remote server
It works only when I add only the server. ftp://server/
Is there any way to add directories to the URL? Or what is wrong in my thought?
I think to use NFS but I'm not sure if that way is better as FTP, because FTP is default
View 4 Replies
View Related
May 18, 2012
I'm trying to restore backup after upgrading Cisco Prime v4.1 to v4.2. However, getting the following error in the log. [code] The log shows the error is a continuous one and affraid it may be a loop. Currently my restore progress is stuck at 70%RME restoration.[code]
View 2 Replies
View Related
Jan 17, 2012
We have an installation of Cisco Prime LMS 4.1 soft appliance on VMware and i would like to ask if it is possible to backup the database on an external drive other than the 'local' LMS hard disk.
View 3 Replies
View Related
Nov 6, 2011
In my WCS v7.0.172.0, I recently configured the Controller Configuration Backup task. Backups seem to be working fine for the past few days. How do I tell it how far back I want to keep logs, or how many log files to keep before deleting the older ones? Seems like it will just keep on saving the config backups with a date stamp until the TFTP server runs out of disk space.
View 3 Replies
View Related
Jun 13, 2012
I have to install Prime LMS 4.2 on ESX customer infrastructure (ova image as soft appliance). The customer would like to know if LMS 4.2 is compatible with his backup agents :
* Symantec Veritas Netbackup (v7.1.0.2)
* Control-m (v6.4.01.300)
If not, what would be the best solution to backup the server ? Are the VMware tools supported now ?
View 1 Replies
View Related
Jun 3, 2012
I'm replacing an older (& failing) RVS4000 v1 with a new V2. I need to minimize downtime. Will a config backup from the old v1 restore properly to a new v2 (all have newest firmware)? There are a lot of tweaks including several VPNs and to do it all manually is not desirable.
View 2 Replies
View Related
Dec 21, 2011
I need to backup my ASA 5505 configuration and restore it to default, then I'll configure manually the new config, but if something doesn't work I want to restore the backup made before.
I tried the "copy run tftp" command, and it always answers the same: Result of the command: "copy run tftp" [code] I read everywhere its supossed to prompt asking me tftp server address and file name.
View 7 Replies
View Related
May 24, 2012
I have a Cisco 831 router (c831-k9o3y6-mz.124-5c.bin) that cannot backup the config to a local tftp server. I have seen this behavior on a few different Cisco devices over the years and have never found a solution. The connection is made to the tftp server (in this case tftpd but similar behavior on any tftp server) and a blank file is created on the target machine file system, but the data is never transferred.
The router shows %Error opening tftp://192.168.0.2/router-confg (Timed out) [Failed]
The tftpd log shows 5 repeated attempts at the file write.
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:40.922]
Write request for file <router-confg>. Mode octet [25/05 11:56:40.922]
Using local port 61607 [25/05 11:56:40.922]
<router-confg>: rcvd 0 blk, 0 bytes in 3 s. 0 blk resent [25/05 11:56:43.922]
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:43.923]
[Code]...
This is also stopping me upgrading the image on the router as I cannot transfer in the other direction either.
View 1 Replies
View Related
Apr 9, 2013
I have a small doubt with Nexus 7k,5K,2k & 1K.We want to backup the running config to my desktop through tftp.When i tried to backup from Nexus switches showing like below Nexus 7K. [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config Vdc-all". [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric"
It's showing three choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric" or "copy running-config startup-config vdc-all". [code]
View 11 Replies
View Related
May 21, 2012
How can we restore ACS config from an existing backup file, in an ACS cluster deployment? is it through CLI? with"restore"or"acs restore" command? and should I restore only the ACS config or both ACS and ADE-OS config?
View 4 Replies
View Related
Oct 20, 2011
have some problems with setting up jobs for the backup running config on my switches. Have RW and RO contact with everyone and can change the config in editor, but do not get config.txt
View 1 Replies
View Related
Aug 2, 2009
I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies
View Related
Mar 15, 2012
how can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies
View Related
Oct 7, 2012
I have Cisco 2800 series router. When I am trying to write memory getting error message " Error opening flash:config-backup-1 (No more root directory entries available)" When there is simultaneous access to a router's NVRAM, we might encounter these errors. In order to clear the line the other user(s) is (are) connected on and free the NVRAM, issue the clear line command. But still getting the same error message.
View 1 Replies
View Related
Sep 8, 2011
I am using CISCO PRIME LMS 4.1 for manage my network, i ran a device discovery job using a ping sweep on the ip ranges of my network, ie 192.168.1.0/24, 192.168.2.0/24 and so on... the discovery found all my devices, but it discovered duplicate devices with illegal ip Addresses, i.e.,
ip device
192.168.1.255 S1
192.168.2.0 S1
192.168.2.1 S1 (the real address)
all in reachable status.
I don't understand why the program adds that repeated illegal addresses.. How can I run the device discovery to avoid this problem?
View 2 Replies
View Related
Jan 15, 2013
is there anyway to change the IP address of a device without data lost? I saw an option in to change it in Inventory > Device Administration: Add / Import / Manage Devices > Edit identity but from what I read I can get a data lose,
View 1 Replies
View Related
Feb 29, 2012
I am trying to figure out why the Device view has no systlogs in Cisco Prime 4.1.I have everything configured, the switch is sending debugging level logs to the IP of the Prime Server. I am fairly certain it is reporting because it has alot of other information in the server.
View 1 Replies
View Related
Mar 26, 2013
We have a Prime LMS and a Prime NCS instance running. At the moment, instead of having the 2 systems do device discovery independantly, I thought a good way to set things up would be for LMS to do all of the discovery, and then export the DCR from LMS into NCS.
Now doing this manually in a cinch, but I'd like to automate the process. LMS has some nice scripting features that allows me to easily use the 'dcrcli' script to export a CSV file of the all of devices and credentials, which can be put in a format that NCS can bulk import. I plan to do this on a regular basis using a cron entry.
What I can't seem to find is any documentation on how I might be able to achieve the import piece of the puzzle on the NCS box. Are there command line utilities as with LMS that would allow me to import devices, and put the scripting into a cron file to do on a regular basis?
View 3 Replies
View Related
Feb 19, 2013
The problem is that - although negotiated in global discovery settings - Prime appends domain name to the device name so that all switches (not routers) have "confusing names". The domain name is not required in device name. What can i do?
View 2 Replies
View Related
Jan 20, 2013
I have problems with setting the snmp retry / timeout parameters for our devices. I managed to import our devices with bulk import , but after it I realized that for some devices the snmp retry / timeout values were different ( created the bulk file with 3 retries and 30 sec timeout , but in the system the appear with 2 retries and 1 sec timeout). I tried to change it manually , but after a while it goes back to the wrong values.
View 1 Replies
View Related
Apr 9, 2013
We use Cisco LMS Prime 4.1 to archive our Cisco Equipment configurations.
Now we want to store the configurations off site.
View 2 Replies
View Related
Oct 17, 2012
I have a number of devices such as Cisco Call Manager, or Cisco Wireless Controllers, etc that I want to remain in DCR but would like to exclude from the Config Archive process. Is there any way of excluding an individual device from this process?
View 3 Replies
View Related
May 20, 2013
I have recovered some configuration files from my 2950 switches with the Configuration Archive Tool in LMS.
Now, I'd like to replace my old 2950s by 2960 switches, which have the same number of ports.
Will there be any issue if I copy the exact same config from 2950 to 2960 ? Will some features not work or is everything interoperable ? Here's an extract of the config :
Global
version 12.1
no service pad
service timestamps debug date time
service timestamps log date time
no service password-encryption
[ code]....
View 2 Replies
View Related
Nov 25, 2012
before I open a TAC case: How does Cisco Prime NCS handle the device licenses for stack of 3750 switches? Just one device license for the stack or a license for every physical switch in the stack? I can't find a answer on the Cisco website, but maybe one of you knows it from a deployment you have done..
View 2 Replies
View Related
Mar 6, 2012
Is it possible to create a job what automatically export the devices configs that are in the folder CSCOpxfiles medemushadow? It would be wonderdul if CW could export the .cfg files into a .rar and send in email or something like this.
View 1 Replies
View Related
Jun 7, 2011
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies
View Related
Apr 5, 2012
What's a good product to use to backup device configurations?
View 19 Replies
View Related
Jan 13, 2009
we have a Cisco 1801 at one of our remote sites that uses an ADSL line for it's primary connection and ISDN as backup. Despite no apparent problems with the ADSL line the ISDN is repeatedly dialling the internet every 2-3 mins during office hours and considerable expense to the customer.
View 3 Replies
View Related
Aug 8, 2012
We're currently evaluating Cisco Prime LMS 4.2.Something we've been trying to achieve for the past couple of days is to have LMS notify us when a Microsoft Host is Unreachable, and then to notify us once that alarm has cleared (the Microsoft Host is Reachable again).
We're at the point where the Microsoft Host was discovered, LMS incorrectly identified it as a Cisco Call Manager, so we changed it's identity to non-cisco device > microsoft host > microsoft host. LMS currently has the device listed as being in the 'Questioned' state. SNMP timeout has been set to 15 seconds, and the SNMP community is correct.
Being new to LMS Prime, and having not received any training on the product to this point, we turned to the admin guide, but we couldn't find anything that goes into detail for how to manage the notification for non-Cisco devices.
Is what we're trying to achieve possible with Cisco Prime LMS 4.2? We just want to be able to receive simple 'host unreachable' notifications for Microsoft servers, and the corresponding 'cleared' notifications once the server is back online.
View 2 Replies
View Related
Apr 17, 2012
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies
View Related
Nov 15, 2009
I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
View 9 Replies
View Related
