In my WCS v7.0.172.0, I recently configured the Controller Configuration Backup task. Backups seem to be working fine for the past few days. How do I tell it how far back I want to keep logs, or how many log files to keep before deleting the older ones? Seems like it will just keep on saving the config backups with a date stamp until the TFTP server runs out of disk space.
View 3 RepliesWe are currently running Cisco prime 4.1 and want to make sure there is a backup of the configurations from our switches and routers. The VLANconfig is not collected according to the devicestatus dashboard. i am aware there were a known issue with LMS running on a virtual server and vlan not being able to be collected, is this issue resolved? i have tried the various workarounds with TAC support and it hasnt worked. We have the running and startup config collected for our devices when looking at the device status dashboard. does this mean if a switch crashes we can restore the config to a new switch immediately?
i saw there is a version 4.2. maybe this version resolves the issue with LMS on a virutal server? i cannot find the download to upgrade to 4.2 in the support section though.
I'm replacing an older (& failing) RVS4000 v1 with a new V2. I need to minimize downtime. Will a config backup from the old v1 restore properly to a new v2 (all have newest firmware)? There are a lot of tweaks including several VPNs and to do it all manually is not desirable.
View 2 Replies View Related I need to backup my ASA 5505 configuration and restore it to default, then I'll configure manually the new config, but if something doesn't work I want to restore the backup made before.
I tried the "copy run tftp" command, and it always answers the same: Result of the command: "copy run tftp" [code] I read everywhere its supossed to prompt asking me tftp server address and file name.
I have a Cisco 831 router (c831-k9o3y6-mz.124-5c.bin) that cannot backup the config to a local tftp server. I have seen this behavior on a few different Cisco devices over the years and have never found a solution. The connection is made to the tftp server (in this case tftpd but similar behavior on any tftp server) and a blank file is created on the target machine file system, but the data is never transferred.
The router shows %Error opening tftp://192.168.0.2/router-confg (Timed out) [Failed]
The tftpd log shows 5 repeated attempts at the file write.
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:40.922]
Write request for file <router-confg>. Mode octet [25/05 11:56:40.922]
Using local port 61607 [25/05 11:56:40.922]
<router-confg>: rcvd 0 blk, 0 bytes in 3 s. 0 blk resent [25/05 11:56:43.922]
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:43.923]
[Code]...
This is also stopping me upgrading the image on the router as I cannot transfer in the other direction either.
I have a small doubt with Nexus 7k,5K,2k & 1K.We want to backup the running config to my desktop through tftp.When i tried to backup from Nexus switches showing like below Nexus 7K. [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config Vdc-all". [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric"
It's showing three choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric" or "copy running-config startup-config vdc-all". [code]
How can we restore ACS config from an existing backup file, in an ACS cluster deployment? is it through CLI? with"restore"or"acs restore" command? and should I restore only the ACS config or both ACS and ADE-OS config?
View 4 Replies View Relatedhave some problems with setting up jobs for the backup running config on my switches. Have RW and RO contact with everyone and can change the config in editor, but do not get config.txt
View 1 Replies View RelatedI need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies View Relatedhow can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies View RelatedI have Cisco 2800 series router. When I am trying to write memory getting error message " Error opening flash:config-backup-1 (No more root directory entries available)" When there is simultaneous access to a router's NVRAM, we might encounter these errors. In order to clear the line the other user(s) is (are) connected on and free the NVRAM, issue the clear line command. But still getting the same error message.
View 1 Replies View RelatedI have a 3725 router that is reporting the following syslog message:
%FAN-3-FAN_FAILED: Fans had a rotation error reported.
When I do a show environment all, I am getting the following message:
Fan status: Warning- low fan rpm condition detected.
Both the the fans are functional and are rotating fine. How do I repair?
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies View RelatedIf i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedI have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
Powered up device.Held reset for 30 seconds.Power cycled device.Entered 192.168.1.245 into ChromeChrome won't connect
View 1 Replies View RelatedWLAN Controller 4400 series connected to Catalyst 4506 on vlan 12. Access switches got managment vlan 5 and vlan 1 shutdown. what config is needed on ports were Access points are connected. Access switch is in vtp client mode.
View 5 Replies View RelatedI have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies View RelatedCurrently have a 5508 in the lab and testing 4 AP's with it. Eventually there will be 18 AP's spread thru out different floor in our building.
So far access is working fine using WPA, 802.1x and the client configured to use windows logon credentials..But it doesn't seem to automatically transfer between access points.
I have been working with the 871 router and configuring it for work at home users. Now we are purchasing and using the 881's instead. I noticed that after write erasing the router, I need to run the command in the global config "license boot module c880-data level advipservices" just have eigrp.However when I type show license, I get the following:
Index 1 Feature: advipservices
Period left: 8 weeks 3 days
Period Used: 2 hours 55 minutes
License Type: EvalRightToUse
[URL]
There is more but I left it out. However it shows that the advipservices license has only 8 weeks and 3 days left.What is this? I thought that when I buy a brand new router, I should get everything, including IOS licenses. So I would like to know is this a new licensing scheme and how does it get register and how do I get it so that the advipservices license is permanent?
I am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies View RelatedI need to take a new 2504 onsite and get a minmial config on it so I can reach it remotely and finish configuration later.
View 2 Replies View RelatedMy 1140 doesn't write to the config.txt file. I'm not sure why. I have three of these access points that we changed the firmware to make them autonomous. The other two worked fine.
View 1 Replies View Relatedwant to connect three networks with each other via two media one ethernet/fiber optic and other through wireless as backup link.how can i connect these three networks so that if my ethernet/ fiber optic connection fails than computer on networks can still communcate via wireless link (i mean if ethernet/fiber optic fails then wireless link should automatically be established/
View 1 Replies View RelatedCurrently we have 20 remote sites, each with 2-5 AP's each. They all connect back to our Main Data Site in the US and register on a single WLC5508.
We do not have a backup WLC, but are looking to purchase one. What I would like to know is, are there any problems with the secondary WLC being installed in our Main Data Site in Europe? These two main sites are connected via a 10M MPLS WAN.
So all the remote sites could still connect to the WLC in the US, but in the event of a WLC failure in the US, they would need to fail over to the site in Europe
I was changing some settings on the router, disabled the WMM QoS, and I can no longer see either the 2.4 or 5GHz networks. I power cycled, tried resetting to defaults but the wireless seems to be dead. I can manage it wired, but that does me no good.
View 2 Replies View RelatedI have a brand new TMG Installed and setup some rules. But i need to have one wireless router for a special office which should not be filtered by TMG. How can i setup TMG rule and the wireless rounter to not be filtered on TMG ? The linksys wireless rounter should also NOT ask for domain authentication.. it should allow directly access to outside without any authentication.
View 1 Replies View RelatedGot randomly dc'd from my router today, tried reconnecting say that its an unidentified network and there's no internet connection; here's the IP config file
Windows IP Configuration
Host Name . . . . . . . . . . . . : CalumFirth-PC
Primary Dns Suffix . . . . . . . :
[Code].....
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
how to backup a Cisco Wireless Access Point Controller 5508.
View 2 Replies View RelatedHere's the list of equipments:
Pool of oeap 600 aps
1x 2504WLC as OEAP WLC (@DMZ)
1x ASA 5515
Scenario:
My OEAP WLC located at ASA - DMZ is NATted to a public ip (primary internet ISP), then my pool of OEAP-600 were configured to communicate with this OEAP WLC.
My question is:
I want to automate the failover of OEAP-600 (I don't know if this is possible) to the secondary internet ISP whenever the primary internet ISP fails. The secondary ISP is terminated on the same ASA 5515-X doing PBR and IP SLA stuff.
I know that OEAP 600 can only be pointed to one WLC ip address I know that the WLC can only be NATted to one public IP address.
What would be the best solution to perform the OEAP backup connectivity? Or just buy another set of WLC/ASA then just manually configure the OEAP-600 APs to point to the secondary ISP.
My customer has a 4402-25-K9 and need a backup (failover) controller to avoid data transmision break when primary controller goes down.4402 are end of sale so I have a question can I use 5508 to get Controller Failover Protection with 4402 ?
View 3 Replies View RelatedWRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies View Related