Cisco Wireless :: Unable To Log Into WAP 4401 Web Config?
Feb 27, 2012Powered up device.Held reset for 30 seconds.Power cycled device.Entered 192.168.1.245 into ChromeChrome won't connect
View 1 Replies
ADVERTISEMENT
Linksys Wireless Router :: Unable To Connect To WRT54G2 Config Page?
Jul 11, 2011I recently (~month ago) switched to a new computer after my old one (which I had configured the router on previously with no problems) died.Since then, I have been unable to access my router's config page (entering in the ip address simply results in a blank page with no prompt for username/password). Switching browsers (I've tried Firefox 5 and IE 8) does not solve the problem, nor does disabling AdBlockPlus/NoScript on Firefox. Any way to access my router so I can begin forwarding ports again?
View 1 Replies View RelatedLinksys Wireless Router :: WRT610n Unable To Login Config Page Via HTTPS
Jul 13, 2012I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
View 6 Replies View RelatedCisco Firewall :: Unable To Save Config In ASA 5505?
Sep 26, 2012I have ASA 5505 and I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
View 8 Replies View RelatedCisco WAN :: 3750 Stack Unable To Save Config
Jul 4, 2012I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
[code]...
Unable To Login Into Router Config Page
Feb 4, 2013Basically all I want to do is login to my routers config page so that I can forward ports. I was able to this a few weeks ago but recently I have received this error. Failed to connect
Things that I have already tried:
- Tries using 192.168.0.1, 192.168.1.1, http://192.168.1.1 and all kind of variations.
- Tried with different browsers.
- Tried with seperate computer with different OS's (Mac and PC)
- Unable to flush dns because I get this error: CMD prompt error message .
- Have factory reset router a few times now.
- Unplugged, left off for 20mins-2hours.
Cisco Switching/Routing :: ASA 5505 Upload Config File Into Start-up Config
Apr 17, 2012If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedCisco WAN :: 2811 - Startup Config Is Not Copying To Running Config
Nov 15, 2009I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
Cisco Wireless :: 4505 - Port Config For AP
Jul 13, 2012WLAN Controller 4400 series connected to Catalyst 4506 on vlan 12. Access switches got managment vlan 5 and vlan 1 shutdown. what config is needed on ports were Access points are connected. Access switch is in vtp client mode.
View 5 Replies View RelatedCisco Wireless :: LAP1142N Not Saving Config
Feb 11, 2013I have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies View RelatedCisco :: 5508 Wireless Roaming Config
Apr 7, 2011Currently have a 5508 in the lab and testing 4 AP's with it. Eventually there will be 18 AP's spread thru out different floor in our building.
So far access is working fine using WPA, 802.1x and the client configured to use windows logon credentials..But it doesn't seem to automatically transfer between access points.
Cisco Wireless :: WCS V7.0.172.0 - WLC Config Backup Rotation
Nov 6, 2011In my WCS v7.0.172.0, I recently configured the Controller Configuration Backup task. Backups seem to be working fine for the past few days. How do I tell it how far back I want to keep logs, or how many log files to keep before deleting the older ones? Seems like it will just keep on saving the config backups with a date stamp until the TFTP server runs out of disk space.
View 3 Replies View RelatedCisco Wireless :: 881 - Run Command In Global Config / Just Have EIGRP
Apr 29, 2012I have been working with the 871 router and configuring it for work at home users. Now we are purchasing and using the 881's instead. I noticed that after write erasing the router, I need to run the command in the global config "license boot module c880-data level advipservices" just have eigrp.However when I type show license, I get the following:
Index 1 Feature: advipservices
Period left: 8 weeks 3 days
Period Used: 2 hours 55 minutes
License Type: EvalRightToUse
[URL]
There is more but I left it out. However it shows that the advipservices license has only 8 weeks and 3 days left.What is this? I thought that when I buy a brand new router, I should get everything, including IOS licenses. So I would like to know is this a new licensing scheme and how does it get register and how do I get it so that the advipservices license is permanent?
Cisco Wireless :: Command To Save Config On 1142 LAP?
Dec 21, 2011I am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies View RelatedCisco Wireless :: WLC 2504 Minimal Config Setup
Jun 11, 2013I need to take a new 2504 onsite and get a minmial config on it so I can reach it remotely and finish configuration later.
View 2 Replies View RelatedCisco Wireless :: 1140 Doesn't Write To Config.txt File
Nov 8, 2012My 1140 doesn't write to the config.txt file. I'm not sure why. I have three of these access points that we changed the firmware to make them autonomous. The other two worked fine.
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Wireless Non-existent After Config Change?
Aug 27, 2011I was changing some settings on the router, disabled the WMM QoS, and I can no longer see either the 2.4 or 5GHz networks. I power cycled, tried resetting to defaults but the wireless seems to be dead. I can manage it wired, but that does me no good.
View 2 Replies View RelatedSecurity / Firewalls :: Wireless Linksys Wrt54gl / How To Config Via TMG
May 18, 2012I have a brand new TMG Installed and setup some rules. But i need to have one wireless router for a special office which should not be filtered by TMG. How can i setup TMG rule and the wireless rounter to not be filtered on TMG ? The linksys wireless rounter should also NOT ask for domain authentication.. it should allow directly access to outside without any authentication.
View 1 Replies View RelatedWireless Network Connection Doesn't Have A Valid IP Config
Nov 17, 2012Got randomly dc'd from my router today, tried reconnecting say that its an unidentified network and there's no internet connection; here's the IP config file
Windows IP Configuration
Host Name . . . . . . . . . . . . : CalumFirth-PC
Primary Dns Suffix . . . . . . . :
[Code].....
Linksys Wireless Router :: Cannot Access E4200 Config In LAN-to-LAN
Jan 31, 2012I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
Linksys Wireless Router :: WRT120N / Can't Access Config Webpage
Apr 18, 2013WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies View RelatedLinksys Wireless Router :: WRT120N - Can't Access Config Webpage
Jul 15, 2011WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
View 2 Replies View RelatedLinksys Wireless Router :: WRT160Nv2 How To Access Config Screen
Jan 7, 2011how i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
View 9 Replies View RelatedCisco Wireless :: AP541 Access Point Best Config For Multiple VAPS Advice?
Oct 26, 2011I have several AP541 (on different site locations) which I have currently configured for WPA enterprise using windows 2008 as the Radius server. This works fine for staff members who use the wireless when roaming around the offices.
I would also like to setup another VAP for guests to allow them to access our internet but nothing else on the network. I was wondering what approach would be the best one to adopt to achieve this. Would I be best to setup a WPA Personal VAP and allow guests to access the wireless this way. Or is there a better approach? If we did adopt this approach I presume this would mean that we have to log onto each AP in turn and then change the WPA key on each one everytime we decide to change the key? Or is there some clever software I could use to change them all in one go.
TP-Link 300Mbps Wireless :: Access TL-WR1043ND Cable Router Config Without Pin?
Jan 14, 2013Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : Virgin Media
Bought recently and I'm very pleased with Setup and Performance.
However, even though I have tried repeatedly with different user details and passwords I cant access the router Config without resetting to defaults using the pin in the back and admin admin.
I am using W7 and get to a log in screen via Control Panel / ... Network Sharing Centre / Network Map and see Router. Click on this and up comes a User Name and Pasword form but it never works with what I entered for the router.
Cisco VPN :: ASA 5510 - Twice NAT Config
Sep 11, 2011I'm running into and interesting issue concerning a twice NAT config.
We have a remote site that needs to connect to a server cluster on our end. Using ASDM I have created a NAT rule that uses PAT to map our server addresses to a single IP (this is due to constraints placed on us by the remote site). This in and of itself shouldn't be a problem. The issue is that the VPN tunnel won't come up unless I also map an address to the remote site's sever.
Example:
Appliance: ASA 5510
ASA Version: 8.4(2)
ASDM Version: 6.4(5)
Original Packet:
Source Interface: inside
Destination Interface: outside
Source Address: Server_Cluster
Destination Address: Remote_Server
Service: any
Translated Packet:
Source NAT Type: Dynamic PAT (Hide)
Source Address: Mapped_Server_Cluster_Address
Destination Address: Mapped_Remote_Server_Address
Service: -- Original --
Within the Translated Packet section, if I set Destination Address to the actual remote server address nothing happens when I attempt to bring up the tunnel. However, if I map an address to the remote server, the tunnel begins to come up and then fails during phase two (as the mapped address doesn't match the addressing that has been defined in the remote end's connection profile).
Initially I thought the issue may be due to an IP addressing overlap since both sites are running similar numbers, but the default route statement on our ASA, should contend with this issue. Also, each time I change the NAT rule, I change the connection profile to match those changes.
So, ultimately, what I wish to accomplish is to allow connectivity between my site and the remote site without having to map another address to their remote server. How may I do this?
Cisco VPN :: 800 VPN Config To New ASA5505
Jul 8, 2012I have 2 office buildings using Cisco 800 series routers with a L2L VPN between both. I'm upgrading the router to an ASA5505 at one of the offices but can't figure out the L2L VPN on the ASA. Specifically, can't figure out how to set the pre-shared key. On the Cisco 800 it's:That doesn't seem to work on the ASA. Here is my current config on the Cisco 800. [code]
View 9 Replies View RelatedCisco Firewall :: NAT Config Changes From 6.2 To 8.4?
Sep 14, 2011I am converting one PIX config (in 6.2) format to 8.4 format manually.I am stuck at the following statements.
---------------------------
global (outside) 1 192.168.21.100-192.168.21.150 netmask 255.255.255.0
global (outside) 1 192.168.21.44 netmask 255.255.255.255
nat (inside) 0 access-list 101
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-list 101 permit ip host 10.130.101.2 10.132.102.0 255.255.255.0
-----------------------------
My understanding from the old config file was that any traffic coming from source 10.130.101.2 to destination 10.132.102.0 would NOT be translated and this shall remain the same in 8.4.How can I rewrote the NAT commands?
Cisco :: How To Turn Off Logging Esm Config
Feb 7, 2013How do I turn off "logging esm config"? I tried conft no logging esm config and that worked for the moment, but when the switch reboots, or I run reload, it comes back.What does that do anyway? This switch was giving an out of memory error and seemed to be flooded with messages, so I trying to turn logging off/lower the log level.
View 5 Replies View RelatedCisco :: VOIP QoS Config Not Matching?
Aug 15, 2011my config and all the show's ive run sofar tryign to figure this out, but the policy map isnt matching the traffic for some reason
View 9 Replies View RelatedCisco WAN :: How To Set Config-register On 2960
Feb 6, 2007I have tried the config-register command and it is not available. Here is part of the show ver command. I want to change the config-reg from 0xF to 0x2102.I have run into this before but don't remember how to correct it.....I think I have to use the boot command but not sure. Here it the output show ver Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
ROM: Bootstrap program is C2960 boot loader
BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
System returned to ROM by power-on?System image file is "flash:c2960-lanbase-mz.122-25.FX/c2960-lanbase-mz.122-25.FX.bin"cisco WS-C2960-24TT-L (PowerPC405) processor (revision A0) with 61440K/4088K bytes of memory.last reset from power-on
4 Virtual Ethernet interfaces
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.64K bytes of flash-simulated non-volatile configuration memory.
Model number : WS-C2960-24TT-L
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT-L 12.2(25)FX C2960-LANBASE-M
Configuration register is 0xF
Cisco WAN :: ASA 5510 Config For Failover
Aug 2, 2011We have two offices in the US and one in Mexico. Our site in Mexico connects to our headquarters in the US over an AVPN/ MPLS circuit .Mexico has a separate Internet connection through TelMex. There is an ASA 5510 at headquarters and an ASA 5505 in Mexico. We have a fail over VPN set up in the ASAs for times when the MPLS circuit goes down. All Internet traffic in Mexico is supposed to be routed to the TelMex connection. All company traffic is supposed to be routed to the Cisco router. ASA is supposed to be last resort route. We have a fail over VPN set up in the ASAs for times when the MPLS circuit goes down. (Or at least we did until I had someone work on the configuration) Everything had been working fine for the last 4 years.
Yesterday when the MPLS went down, so did their Internet connection. I realized the Internet traffic is now coming through the MPLs circuit to head quarters and out our ASA. Obviously there is a problem with the configuration. I do not have enough experience to figure this out. I have attached the configs and the routes for both the ASA and the router.
Cisco :: Deploying Config Templates With LMS 4?
Jul 31, 2011I tried to deploy configuration templates with Cisco LMS Template Center, due to the 10 Cool LMS Tricks to better manage your network i am able to do it now.Just i don't know why, after deploying these templates the configuration is not save to the startup-config.another problem i have with the snmp-server location configuration. It seems my template does not support spaces in the textbox. Any way to put spaces in the snmp location?
<parameter name="snmp-location">
<description>SNMP Server Location</description>