have some problems with setting up jobs for the backup running config on my switches. Have RW and RO contact with everyone and can change the config in editor, but do not get config.txt
View 1 RepliesI'm replacing an older (& failing) RVS4000 v1 with a new V2. I need to minimize downtime. Will a config backup from the old v1 restore properly to a new v2 (all have newest firmware)? There are a lot of tweaks including several VPNs and to do it all manually is not desirable.
View 2 Replies View Related I need to backup my ASA 5505 configuration and restore it to default, then I'll configure manually the new config, but if something doesn't work I want to restore the backup made before.
I tried the "copy run tftp" command, and it always answers the same: Result of the command: "copy run tftp" [code] I read everywhere its supossed to prompt asking me tftp server address and file name.
How can we restore ACS config from an existing backup file, in an ACS cluster deployment? is it through CLI? with"restore"or"acs restore" command? and should I restore only the ACS config or both ACS and ADE-OS config?
View 4 Replies View RelatedIf the hostnames are the same - can I restore the backup file from a wcs 5.2.148.0 instance on a different wcs instance running wcs 6.0.196.0?
View 1 Replies View RelatedI have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies View RelatedI have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
We have cisco works LMS 3.1 and the server have very problems, we need format the server and reinstall the Cisco Works, when I doin backup and restore of data LMS We lost the licenses? or when we restore the data in the server we have the same licenses? or get the new licenses to cisco?
View 5 Replies View RelatedI am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies View RelatedI have a cisco ASA 5540 and i cant make a simple PAT (many private IP to one public IP). Below you can find my conf.
[code]...
I am facing a failed issue when restoring the WCS Database. Below is the error i get, does any one out there facing it before?
#######################################
[root@egwgwcs WCS7.0.220.0]# ./Restore
Please enter the full path of the backup file name: /opt/WCS7.0.220.0/Backup_File/WCS_Aug2012.nmsbackup
Untaring the backup file...
Failed to untar backup file. Exception: invalid stored block lengths
Restore database failed.
#######################################
I want to restore a backup from c2960 to other one.Why is recommended to remove any security commands, like AAA?
View 2 Replies View RelatedI've been setting up building and testing our new ACS 5.x boxes and I've been running into a spot of bother with the backup restore feature. This most likely due to my unfamiliarity with the tool.
As part of my testing for Backup/Restore, I first backup the data using the Removal and backup tool in Secure ACS View (found under data management. I then confirm that the new FULL backup has been populated my test repository and is available in the restore feature. (also under Data Management) My next step is to create a few test Network Device Groups, Identity groups, and users Then I go back to the restore feature select the Back up file I just created, I also check the box Skip View Database backup before Restore and hit the restore button.
The box goes through the expected steps including a reload. When it comes back up I would expect the test users, groups etc I created after the last backup to be gone as they did not exist at that time. Although I find the opposite is true. Any settings I made after the last backup are still present. I do not have incremental backups enabled.
I essentially want to test a backup of the database of users and groups/rules etc make changes and then restore that database to the previous backed up configuration.
We want to take the current configuration backup of the LMS 4.0 (Installed on Win 2003 Enterprise) and restore the same to a new windows machine (Win2003 standard edition).
View 1 Replies View RelatedI have a Cisco ASA 5505 as a BOVPN endpoint using certificates. The config is complete and I now need to back it up and restore to a cold standby Cisco ASA 5505 that will sit on the shelf until something goes wrong.
Problem is I cannot restore my certifcates to the standby.
I have tried the backup and restore wizard in ASDM and to be honest it didn't work.
I recently tested the process for a customer of defaulting a Cisco WLC to factory configuration and then restoring the configuration from Cisco NCS. It was not seamless to say the least and I wonder if I have just gone about it the wrong way.
Have have set the NCS platform to configuration sync with the 5508 controllers at 04:00 every day and prior to the controller defaulting I ensured that NCS also reported that the config was in sync. I have also set NCS to complete a tftp backup of the controller every night 23:00 - interestingly though I have no idea where this is stored on the NCS platform ( a VM appliance ) or what it's file name is.
Anyway my experiences where as follows:-
1. defaulted WLC and via serial CLI ended up at the configuration wizard.
2. Set the correct LAG, management IP, host name that NCS knew this controller by.
3. To test things just created a dummy WLAN ( SSID ) as I assumed this would be overwritten ( big mistake ! ).
At this point I connected the controller to the network and tried to restore the configuration from the config sync version.
First problem - you have to remember to set up the SNMP community string you were using as it is needed by the configuration sync process. After adding this to the controller I could push the configuration to the controller.
Second problem - failed to add the first WLAN from the backup as I have added the temporary dummy W LAN via the wizard and NCS reported a conflict. So had to delete WLAN ID 1 from the WLC GUI directly and then the config push no longer reported this error.
Third problem - for some reason did not add the TACACS server details - reported the error that it could not added them. I manually added these via a template via NCS and all was well.
Fourth problem - all but the first WLAN was in the disabled state - had to re-enable all of the WLANs.
Fifth problem - any default items I had disabled or removed have not been saved - therefore I have removed the public and private SNMP communities - but these were still on the WLC after the restore. I have disabled unused ports not in the LAG as they show an error in NCS - these where not disabled after the restore.
So all in all not a very satisfactory restore process from NCS to an defaulted WLC ( meant to simulate to the customer what would be needed if they had to replace a controller due to hardware failure ).
Is there anyway to backup and restore the spams quarantine to another ironport c170?
View 1 Replies View RelatedI am in the process of setting up an interop lab for some engineers. The enviornment will consist of some 3750's, H3C's and ProCurves. My concern is that the end user will have Priv-Exec access for CLI usage on the 3750's and they can change the "en" password (I hope they don't but it has happened).Is there a way I can "break in" during the boot process to reset the password? The reason I am doing it this way is because I have an Altiris server with rebuild automation scripts in xpect and I would like to automate the process so I do not have to use a manual factory default reset.
View 5 Replies View RelatedI have a WAG160N and its seems to have reset to factory defaults, no idea why, but when trying to restore the Configuration Backup all I get is "Restore Failure <Unmatched pid>"
View 2 Replies View RelatedWe are trying to make a restore from the backup done on ACS version 5.1 to a new appliance running ACS5.2 Before doing it I found this note in Cisco ACS user guide:
Note: You cannot back up data from an earlier version of ACS and restore it to a later version. Backup and restore must be performed on the same version of ACS. If you need the data on a different version of the ACS, you can perform an upgrade after you restore the data. Refer to the Installation and Setup Guide for Cisco Secure Access Control System 5.1 for more information on upgrading ACS to later versions.
How should I understand it? This note has conflicting statements. We can't restore to a later version but if you need data on a different version of ACS you can perform an upgrade AFTER YOU RESTORE the data. Doesn't it mean that the restore will still work? How would I do the upgrade to version 5.2 or even version 5.3 that was announced to be released very soon? I didn't find anything on the software upgrade in ACS5.1 guide.
I'm trying to move from a faulty SRP527 to SRP 547 - I tried a Restore from Backup, but it doesn't work.So start from fresh, and I'm having an issue trying to add a 2nd SSID to a VLAN...
I keep getting the error:
"FAILED! SSID 2 has joined another VLAN"
Except it hasn't... its not assigned to any VLAN...
i have a simple router on a stick config which is providing dhcp to a customer SSID. however i don't want employees to stay on it and eat the band width since its open. the lease is set to an hour, is there anyway that i could set it so that once your lease expired it can't be renewed for 4 about 8 hours? I am using a cisco 2600 router in this setup.
View 1 Replies View Relatedhere, am used to the RouterSwitch CLI but been asked to set up an ASA 5505 8.4.Quite simply I am trying to at least test out a static PAT from an external source to an internal server in a test environment and no matter whether I set it up as an auto-nat or a twice-nat whenever I run a packet tracer I end up with the same error. This is the packet-tracer I am running-packet-trace input outside tcp 80.80.80.80 3389 10.240.0.10 3389
Phase: 5
Type: NAT
Subtype: rpf-check
Result: DROP
Config:nat (inside,outside) source static server publicIP service RDP RDP
Additional Information:
[code]....
Now I have a couple of questions initially. I have made the presumption that packet-tracer does not look at any external devices while running - as in as long as the ports are up it doesn't matter what is on the end of them for testing purposes? Is there anything I am missing?I have this morning wiped the config and have simply set up the adapters, a default route and twice nat and am not sure why I keep getting the error. I am sure it is something very simple and I'm being a massive donut!
[code]...
I need to know the command to take the Backup and Restore of IOS Image of 6513 through tftp server.
View 6 Replies View RelatedWe are currently running Cisco prime 4.1 and want to make sure there is a backup of the configurations from our switches and routers. The VLANconfig is not collected according to the devicestatus dashboard. i am aware there were a known issue with LMS running on a virtual server and vlan not being able to be collected, is this issue resolved? i have tried the various workarounds with TAC support and it hasnt worked. We have the running and startup config collected for our devices when looking at the device status dashboard. does this mean if a switch crashes we can restore the config to a new switch immediately?
i saw there is a version 4.2. maybe this version resolves the issue with LMS on a virutal server? i cannot find the download to upgrade to 4.2 in the support section though.
In my WCS v7.0.172.0, I recently configured the Controller Configuration Backup task. Backups seem to be working fine for the past few days. How do I tell it how far back I want to keep logs, or how many log files to keep before deleting the older ones? Seems like it will just keep on saving the config backups with a date stamp until the TFTP server runs out of disk space.
View 3 Replies View RelatedI have a Cisco 831 router (c831-k9o3y6-mz.124-5c.bin) that cannot backup the config to a local tftp server. I have seen this behavior on a few different Cisco devices over the years and have never found a solution. The connection is made to the tftp server (in this case tftpd but similar behavior on any tftp server) and a blank file is created on the target machine file system, but the data is never transferred.
The router shows %Error opening tftp://192.168.0.2/router-confg (Timed out) [Failed]
The tftpd log shows 5 repeated attempts at the file write.
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:40.922]
Write request for file <router-confg>. Mode octet [25/05 11:56:40.922]
Using local port 61607 [25/05 11:56:40.922]
<router-confg>: rcvd 0 blk, 0 bytes in 3 s. 0 blk resent [25/05 11:56:43.922]
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:43.923]
[Code]...
This is also stopping me upgrading the image on the router as I cannot transfer in the other direction either.
I have a small doubt with Nexus 7k,5K,2k & 1K.We want to backup the running config to my desktop through tftp.When i tried to backup from Nexus switches showing like below Nexus 7K. [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config Vdc-all". [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric"
It's showing three choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric" or "copy running-config startup-config vdc-all". [code]
I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies View RelatedI am trying to create a bash script to log into routers and make config changes.I ran into a snag in that I am unable to pass a password for the ssh login.I tried tying an expect script to handle that piece but was unsuccessful.I saw on google something about public/private ssh keys (not the same type used to ssh into the box) but I do not want to go this route.Can this be done in another language other than a bash script?I would like to avoid TCL or EEM if possible, I want to learn a language that I can use for multiple purposes.
View 15 Replies View RelatedWe just changed over to Comcast Business and after changing the outside interface to new IP and setting static route. I have access to internet and everythig appears to be good, However asdm will never fully load, alway stuck at 17% or 77%, and I always see "parsing running config".
When I do a show run it will not fully load either, always stop at certain out put. 5 seconds after pulling the Comcast cable out both asdm and running config will load fine.
When I'm trying to make backup in ACS5.1(in log collector node) it gives me the following error:
FullBackupOnDemand-Job Incremental Backup Utility System Wed Jul 13 16:50:23 EEST 2011 Incremental Backup Failed: CARS_APP_BACKUP_FAILED : -404 : Application backup error Failed,I did it via Monitoring Configuration -> System Operation -> Removal and Backup and then "Backup now" bottom.
I tried to restart ACS services through cli (application stop/start) and different repositories (ftp, tftp) but without success.
When I'm trying to make backup in ACS5.1(in log collector node) it gives me the following error:
FullBackupOnDemand-Job Incremental Backup Utility System Wed Jul 13 16:50:23 EEST 2011 Incremental Backup Failed: CARS_APP_BACKUP_FAILED : -404 : Application backup error Failed
I did it via Monitoring Configuration -> System Operation -> Removal and Backup and then "Backup now" bottom.
I tried to restart ACS services through cli (application stop/start) and different repositories (ftp, tftp) but without succes.