Cisco AAA/Identity/Nac :: Unable To Make Backup In ACS 5.1
Jul 12, 2011
When I'm trying to make backup in ACS5.1(in log collector node) it gives me the following error:
FullBackupOnDemand-Job Incremental Backup Utility System Wed Jul 13 16:50:23 EEST 2011 Incremental Backup Failed: CARS_APP_BACKUP_FAILED : -404 : Application backup error Failed
I did it via Monitoring Configuration -> System Operation -> Removal and Backup and then "Backup now" bottom.
I tried to restart ACS services through cli (application stop/start) and different repositories (ftp, tftp) but without succes.
View 8 Replies
ADVERTISEMENT
Jan 28, 2012
When I'm trying to make backup in ACS5.1(in log collector node) it gives me the following error:
FullBackupOnDemand-Job Incremental Backup Utility System Wed Jul 13 16:50:23 EEST 2011 Incremental Backup Failed: CARS_APP_BACKUP_FAILED : -404 : Application backup error Failed,I did it via Monitoring Configuration -> System Operation -> Removal and Backup and then "Backup now" bottom.
I tried to restart ACS services through cli (application stop/start) and different repositories (ftp, tftp) but without success.
View 2 Replies
View Related
Apr 5, 2011
I am not able to backup ACS 5.x server by means of SFTP protocol. We use ACS 5-2-0-26-2. My configuration of repository is:
repository SFTP
url sftp://x.x.x.x/home/user
user user password hash 455ad
command 'backup acs01 repository SFTP' does not work and I receive the following error message on ACS server:
%SSH connect error
On my sftp server I can find the following error messages:
Apr 6 06:57:46 CR01 sshd[8561]: Accepted password for user from 10.20.86.72 port 47924 ssh2Apr 6 06:57:46 CR01 sshd[8563]: Received disconnect from 10.20.86.72: 11: disconnected by user
How to successfully performed backup by means of SFTP protocol? Do I need any other configuration settings except repository? Do I need to store my SSHD RSA key to ACS? I am able to copy files using SFTP from other computers, so it seems that SFTP server is set correctly.
View 2 Replies
View Related
Jun 1, 2011
I have a Domain Controller on windows 2003 advanced server. and I have roles and some configuration such as rights, user accounts, DHCP configuration, DNS server and etc on it.Some times windows needs to be reinstalled but after reinstalling,configuration of roles would be lost. I don't know how can I backup these settings? Is there any solution about this problem.I know a simple way is creating an image of windows installation drive by an application such as Norton Ghost but I'm talking about windows solution.
View 3 Replies
View Related
Oct 20, 2011
have some problems with setting up jobs for the backup running config on my switches. Have RW and RO contact with everyone and can change the config in editor, but do not get config.txt
View 1 Replies
View Related
Nov 27, 2011
I tried to backup ACS 5.1 but i found error messages as below
acs backup25Nov11 repository 25Nov11Repository
% Repository not found
% Error: Invalid repository name 25Nov11Respository
Please use a configured repository.
View 2 Replies
View Related
Jun 8, 2012
How to backup the configuration on cisco acs 5.2 and how to restore it , if some thing wrong happened
View 7 Replies
View Related
Mar 10, 2013
Cisco ACS 5.x appliance?How to back up Config?What is best way, via TFTP? COPY Startup-config tftp:?COPY Running-config tftp:?I currently use Solarwinds CatTolls to back my Cisco Switches, can I use this for Cisco ACS also?
View 3 Replies
View Related
May 19, 2013
we have ACS 4.1 appliance and will do upgrade to 4.2. We need backup user database and system settings.via Gui I am not sure what all we backed up - dmp file seems to be only encrypted user databse but it can be crypted back up file.
How is possible do complete backup of current machine (user database and system config)? Is it possible via Gui or has to be done CLI access?After upgrade will be on machine previous config and database or or will be appliance completelly re-imaged?
View 1 Replies
View Related
Oct 20, 2011
I've been setting up building and testing our new ACS 5.x boxes and I've been running into a spot of bother with the backup restore feature. This most likely due to my unfamiliarity with the tool.
As part of my testing for Backup/Restore, I first backup the data using the Removal and backup tool in Secure ACS View (found under data management. I then confirm that the new FULL backup has been populated my test repository and is available in the restore feature. (also under Data Management) My next step is to create a few test Network Device Groups, Identity groups, and users Then I go back to the restore feature select the Back up file I just created, I also check the box Skip View Database backup before Restore and hit the restore button.
The box goes through the expected steps including a reload. When it comes back up I would expect the test users, groups etc I created after the last backup to be gone as they did not exist at that time. Although I find the opposite is true. Any settings I made after the last backup are still present. I do not have incremental backups enabled.
I essentially want to test a backup of the database of users and groups/rules etc make changes and then restore that database to the previous backed up configuration.
View 2 Replies
View Related
Sep 4, 2011
I have ACS 5.2 in standalone mode in operation and need not incorporating a second server for high availability ACS, the new ACS is a version 5.1
What should I do first, upgrade the ACS version 5.2 and created the high availability or high availability and get up after the upgrade?
View 2 Replies
View Related
Jun 6, 2012
Due to some wrong access policy applied in the administration control settings. GUI access is not functioning. So we need to take a backup thru CLI mode using FTP server. I have tried using the backup command in the console & taken the backup using the following steps. But the backup file is less than 1kb. I need the exact Db backup to be taken.
Step 1 Log in to the ACS SE. For more information, see Logging In to the Solution Engine from a Serial Console.Step 2 At the system prompt, enter backup and press Enter.Tip You can enter the following parameters after the command or in response to subsequent prompts: [server] [username] [filepath]Step 3 At the Enter FTP Server Hostname or IP Address: prompt, enter the FTP server IP address or hostname, and press Enter.Step 4 At the Enter FTP Server Directory: prompt, enter the FTP server directory pathname, and press Enter.Step 5 At the Enter FTP Server Username: prompt, enter the FTP server username and. press Enter.Step 6 At the Enter FTP Server Password: prompt, enter the FTP server password and, press Enter.Step 7 At the File: prompt, enter the name that you want to give the backup file, and press Enter.Step 8 At the Encrypt Backup file? <Y or N>: prompt, enter Y to encrypt the backup file or N not to encrypt it, and press Enter.Caution This procedure interrupts the use of the ACS SE for AAA services.Step 9 If you entered Y to encrypt the backup file, at the Encryption Password: prompt, enter a password and then press Enter.Result: The console displays:Backing up now . . .
All running services will be stopped and restarted automatically.Are you sure you want to proceed? <Y or N>Step 10 To proceed, enter Y and press Enter.
View 5 Replies
View Related
Feb 8, 2012
I have ACS 4.2 on vmware machine, everything is working fine. Automatically backup is already set on local machine, but the thing is, i want to configure automatically backup on my file server (ex. \1.1.1.1acsbackup). Even though i have defined the acsbackup folder through map drive but no success. when i define the above string in the backup location directory, it shows an error (no directory exists). How do i configure file server or map drives on acs & save daily backup on fileserver
View 1 Replies
View Related
Aug 15, 2012
When doing a backup on any of the ACS 5.x appliances by default the backup is encrypted with PGP. What password is used for that? Is it configurable?
View 3 Replies
View Related
Feb 21, 2012
We have ACS 5.3, and trying to set up sftp backup on freesshd server. SSH connection works, but ACS cannot copy backup file to sftp server, we get following errors:
Acs.MGMT.ACSVIEW Backup failed: CARS_XM_SSH_CONNECT : -306 : SSH connect error
FTP backup works fine.
View 1 Replies
View Related
Jan 20, 2013
I had ACS 5.2 ( Evalution License ) setup installed on VMware with patch 11 when I try to restore earlier backup of ACS gives me error "Cannot find acsbackup_instance.log in the backup file"
I am using Filezilla FTP sever for backup transfer.
View 5 Replies
View Related
Dec 27, 2012
I have ACS 5.3.0.40 Primary Secondary Authenticators , of which the Scheduled backup has stopped.When checked the : Monitoring Configuration > System Operations > Data Management > Removal and Backup > Incremental Backup , it had changed to OFF mode. without any reason.Later i did the acs stop/start "view-jobmanager" and initiated the On-demand Full Backup , but no luck, same error reported this time too.
View 2 Replies
View Related
Apr 10, 2013
I'm doing a basic setup of ACS 5.3. For now, I'm configuring backup to a local repository
!
repository Backup
url disk:/Backup
!
How can I automatically delete old files? I need to keep only the last seven files.
View 2 Replies
View Related
Feb 26, 2013
So I've decided to utilize 802.1x on a switch module on a 2901, reasons being for mobility for a laptop and network security.
However, the 802.1x authentication occurs over the VPN Tunnel (over the Internet). What our concern is, what happens if the Internet or Tunnel goes down? I know that 802.1x does not authenticate against the IOS local DB, so what would be another option in case this scenario happened?
There will only be one device authenticating (maybe 2) and they are 2 HP Windows 7 laptops.
View 4 Replies
View Related
Oct 3, 2011
We are trying to make a restore from the backup done on ACS version 5.1 to a new appliance running ACS5.2 Before doing it I found this note in Cisco ACS user guide:
Note: You cannot back up data from an earlier version of ACS and restore it to a later version. Backup and restore must be performed on the same version of ACS. If you need the data on a different version of the ACS, you can perform an upgrade after you restore the data. Refer to the Installation and Setup Guide for Cisco Secure Access Control System 5.1 for more information on upgrading ACS to later versions.
How should I understand it? This note has conflicting statements. We can't restore to a later version but if you need data on a different version of ACS you can perform an upgrade AFTER YOU RESTORE the data. Doesn't it mean that the restore will still work? How would I do the upgrade to version 5.2 or even version 5.3 that was announced to be released very soon? I didn't find anything on the software upgrade in ACS5.1 guide.
View 4 Replies
View Related
Jul 27, 2011
We have an issue with View db (Monitoring & Reports) backup on ACS, version 5.2.0.26. We have scheduled incremental backup daily and full backup monthly. Everything has been working well, but since yesterday following errors have appeared, and full and incremental backup stopped working:
Alarm Name
System Alarm [Incremental Backup]
Cause/Trigger
On-demand Full Backup failed
Alarm Details
CARS_BR_BACKUP_CREATE : -405 : Internal error: couldn't create backup file
Alarm Name
[code]....
We use same repository as always. Backup to the same repository works from CLI.
View 2 Replies
View Related
Oct 30, 2011
After ACS upgrade from 5.2 to 5.3 we have noticed that backup files are significantly smaller in size. For example before the upgrade they were:
285633099 2011-10-23 22:01 Meduza-ACS-111023-2200.tar.gpg
285809254 2011-10-24 22:01 Meduza-ACS-111024-2200.tar.gpg
And after upgrade:
124234429 2011-10-25 22:00 Meduza-ACS-111025-2200.tar.gpg
124234425 2011-10-26 22:00 Meduza-ACS-111026-2200.tar.gpg
What could cause this behavior? How we can be sure if backup files have been regular after the upgrade?
View 5 Replies
View Related
Sep 13, 2011
I have Cisco works LMS 3.2. When i take manual backup, it hits following error,
ERROR(1101): Database dfmInvDb backup failed.
Validation e:/backup_newdfmdatabasedfmInv.db failed.
[Wed Sep 14 15:53:41 2011] Validation e:/backup_newdfmdatabasedfmInv.db failed Validation e:/backup_newdfmdatabasedfmInv.db failed. [Wed Sep 14 15:53:41 2011] Validation e:/backup_newdfmdatabasedfmInv.db failed.
View 4 Replies
View Related
Apr 26, 2011
I am running windows based acs 3.3 in my lan environment going to be replaced with acs 1120 appliance running acs 4.2.1.15 , ACS 3.3 database has been built upto 4.2.0.124 ,step by step by upgrade process
1) acs 3.3.3.14---> 4.1.1.24
2) acs 4.1.1.24 ----> 4.2.0.124 .
now my database is with 4.2.0.124 dmp file , I cannot upgrade my database to 4.2.1.15 because 4.2.1.15 patch is not applicable & executable on 90 days evalution package of 4.2.0.124 of windows platform .
can i import my windows based 4.2.0.124 datbase directly to my acs appliance running 4.2.1.15.3 ??? , else its requires any step to be done to modify the windows based databse matching to appliance windows verison once .
I could see on appliance under restore settings the following options (restore from 4.2.0 backup file to acs 4.2.1)
View 8 Replies
View Related
Nov 11, 2012
to backup an ACS 5.3 vm running on ESXi 5.0 our backup admin requested to install vmware tools on the acs server.
View 2 Replies
View Related
Mar 12, 2013
i've got up and running a webportal on my asa 5520 os 8.2.5 and but i can not make the ssh plugin ver ssh-plugin.111006 work, all of the others work well, no matter what web browser i use always fail, I even upgraded to the version ssh-plugin.120911 but with no luck, is there a debug or something that i could use to make it work properly?
View 2 Replies
View Related
Oct 6, 2011
I ve just finished setting up my first serial connections between two sites using Cisco 1800 routers. I can make connections from Site A to Site B using Windows XP clients, eg accessing exchange server 2007 running on Windows 2003x64, but the main problem is that when I try to configure Windows 7 clients to connect to exchange server on the other site, I can't make connections , no ping, no ssh , no http. What amuses me more is that I can connect to Windows 2008 servers using both Windows XP and 7.
View 5 Replies
View Related
Jul 27, 2011
I m unable to take backup of Switch c2960 using
#Copy flash: tftp
while i m taking it show some error
t#copy flash: tftp:
Source filename []? c2960-lanbasek9-mz.122-44.SE6
Address or name of remote host []? 10.23.120.15
Destination file name [c2960-lanbasek9-mz.122-44.SE6]?
%Error reading flash:c2960-lanbasek9-mz.122-44.SE6(Is a directory)
sh flash:
Directory of flash:/
2 -rwx 1919 Mar 1 1993 10:27:17 +05:30 private-config.text
3 -rwx 11056 Mar 1 1993 10:27:17 +05:30 config.text
4 -rwx 804 Mar 1 1993 05:30:42 +05:30 vlan.dat
6 -rwx 2072 Mar 1 1993 10:27:17 +05:30 multiple-fs
7 drwx 192 Mar 1 1993 05:37:02 +05:30 c2960-lanbasek9-mz.122-44.
SE6
View 1 Replies
View Related
May 11, 2011
For a while now i have been making netowrk bridges to connect my laptop's wireless router to my ethernet port, and every now and then i delete the bridge and make it again. for some reason, a couple of days ago, while trying to make a bridge my laptop said "an unexpected error occured while trying to configure the network bridge"
[code]...
View 1 Replies
View Related
Jul 10, 2012
W7. Internet connection is through BT Home Hub2 and is hardwired. No problem at all. But my wireless connected BT internet radio and my wife's Kindle can no longer connect to the internet. The radio says connecting to network but does nothing. I have changed nothing I am aware of. I have looked at the BT Home Hub Wireless set up page and the settings are Using WPA and WPA2 and the correct wireless encryption key is there. Channel selection is automatic. I have changed that to 3 other suggested channels, no result. Frankly it is all Greek to me and I do not know what I am looking at. how I reconnect the Kindle by wireless and the internet radio? (I know I can use a USB to connect the Kindle, but not the radio).
View 1 Replies
View Related
Sep 5, 2012
i now learning about SSLVPN, and i already install license in 1941 with SSL and security9 License, i learning how to make a gateway for SSLVPN full tunnel, but i meet an obstacles, when i go to my wan ip address https://wan ip address, the browser give this
SSL connection error Unable to make a secure connection to the server. This may be a problem with the server, or it may be requiring a client authentication certificate that you don't have.
Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error
[code]...
View 1 Replies
View Related
Oct 9, 2012
I have a Cisco 527w which we are wanting to deploy to our remote sites however i've found a bug. We use ADSL with an IPsec tunnel as primary and 3G APN for failover . When the ADSL goes down the route via the IPSec tunnel remains and i am unable to route the traffic via the APN backup without disabling the VPN tunnel .
View 0 Replies
View Related
Sep 15, 2012
We have CUCM & lync server setup and its working fine if any one calling each other with DNS load balancing. But customer want ot use Cisco ACE 4710 instead of DNS LB.We have configured Cisco LB and deploy but when CUCM user calling to lync user call going to disconnect after 4 sec and also Lync users unable to make call to CUCM.And also LB deploye between share point but when users are trying to open web session that time web page going to show page cannot display.
[code]....
View 1 Replies
View Related
