Cisco Switching/Routing :: Command In 6513 To Take IOS Image Backup And Restore?
Apr 18, 2013I need to know the command to take the Backup and Restore of IOS Image of 6513 through tftp server.
View 6 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Replacing A Backup Sup 720 On 6513
Nov 21, 2011I am replacing a faulty sup720 on a 6513. It s the backup/hot not the active sup. It has the same IOS on it. Is it correct that all I need to do is remove the faulty and replace it with the new sup and do a wr mem? Fromwat I have read their should be no down time all connectivity should remain stable?
View 6 Replies View RelatedCisco Switching/Routing :: Run VSS On 6513 / 6509 Considering Both Has Same Supervisor Engine 2T And IOS Image
Jun 25, 2012Is it possible to run VSS on 6513 and 6509 when considering both has same supervisor engine 2T and same IOS image.
View 1 Replies View RelatedCisco Switching/Routing :: Backup And Restore ASA 5505 Config
Dec 21, 2011 I need to backup my ASA 5505 configuration and restore it to default, then I'll configure manually the new config, but if something doesn't work I want to restore the backup made before.
I tried the "copy run tftp" command, and it always answers the same: Result of the command: "copy run tftp" [code] I read everywhere its supossed to prompt asking me tftp server address and file name.
Cisco Switching/Routing :: 6513 Removing AAA Command
May 16, 2012I was working on adding a Cisco 6513 to TACACS but ran into trouble. While I work on the issue offline (recreate and test another switch), I wanted to place this switch on radius temporarily.
For some reason i cant undo/delete the AAA commands in order to point to my radius server. Below was done via console: [code]
I disabled my telemetry port on the Cisco 6513 as a precaution. The IOS im using is "s72033-advipservicesk9_wan-mz.122-33.SXI5.bin".how to remove the AAA authentication statement. Hope its not intrusive cause i have a customer on the box.
Cisco Switching/Routing :: 6513-E / 6513 And WS-X6748-GE-TX Compatibility
Oct 29, 2012we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.
View 4 Replies View RelatedCisco :: Backup And Restore LMS 3.1?
Apr 11, 2012We have cisco works LMS 3.1 and the server have very problems, we need format the server and reinstall the Cisco Works, when I doin backup and restore of data LMS We lost the licenses? or when we restore the data in the server we have the same licenses? or get the new licenses to cisco?
View 5 Replies View RelatedCisco :: WCS 7.0.220.0 Backup Restore Failed
Aug 21, 2012I am facing a failed issue when restoring the WCS Database. Below is the error i get, does any one out there facing it before?
#######################################
[root@egwgwcs WCS7.0.220.0]# ./Restore
Please enter the full path of the backup file name: /opt/WCS7.0.220.0/Backup_File/WCS_Aug2012.nmsbackup
Untaring the backup file...
Failed to untar backup file. Exception: invalid stored block lengths
Restore database failed.
#######################################
Cisco WAN :: Restore Backup From C2960 To Other One?
Jan 8, 2012I want to restore a backup from c2960 to other one.Why is recommended to remove any security commands, like AAA?
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.1 Backup Restore?
Oct 20, 2011I've been setting up building and testing our new ACS 5.x boxes and I've been running into a spot of bother with the backup restore feature. This most likely due to my unfamiliarity with the tool.
As part of my testing for Backup/Restore, I first backup the data using the Removal and backup tool in Secure ACS View (found under data management. I then confirm that the new FULL backup has been populated my test repository and is available in the restore feature. (also under Data Management) My next step is to create a few test Network Device Groups, Identity groups, and users Then I go back to the restore feature select the Back up file I just created, I also check the box Skip View Database backup before Restore and hit the restore button.
The box goes through the expected steps including a reload. When it comes back up I would expect the test users, groups etc I created after the last backup to be gone as they did not exist at that time. Although I find the opposite is true. Any settings I made after the last backup are still present. I do not have incremental backups enabled.
I essentially want to test a backup of the database of users and groups/rules etc make changes and then restore that database to the previous backed up configuration.
Cisco :: LMS 4.0 Server Backup / Restore
Mar 9, 2012We want to take the current configuration backup of the LMS 4.0 (Installed on Win 2003 Enterprise) and restore the same to a new windows machine (Win2003 standard edition).
View 1 Replies View RelatedCisco VPN :: ASA 5505 - Backup Restore Certificates
Oct 10, 2011I have a Cisco ASA 5505 as a BOVPN endpoint using certificates. The config is complete and I now need to back it up and restore to a cold standby Cisco ASA 5505 that will sit on the shelf until something goes wrong.
Problem is I cannot restore my certifcates to the standby.
I have tried the backup and restore wizard in ASDM and to be honest it didn't work.
Cisco :: 5508 - NCS Configuration Backup And Restore Of WLC
Jan 10, 2012I recently tested the process for a customer of defaulting a Cisco WLC to factory configuration and then restoring the configuration from Cisco NCS. It was not seamless to say the least and I wonder if I have just gone about it the wrong way.
Have have set the NCS platform to configuration sync with the 5508 controllers at 04:00 every day and prior to the controller defaulting I ensured that NCS also reported that the config was in sync. I have also set NCS to complete a tftp backup of the controller every night 23:00 - interestingly though I have no idea where this is stored on the NCS platform ( a VM appliance ) or what it's file name is.
Anyway my experiences where as follows:-
1. defaulted WLC and via serial CLI ended up at the configuration wizard.
2. Set the correct LAG, management IP, host name that NCS knew this controller by.
3. To test things just created a dummy WLAN ( SSID ) as I assumed this would be overwritten ( big mistake ! ).
At this point I connected the controller to the network and tried to restore the configuration from the config sync version.
First problem - you have to remember to set up the SNMP community string you were using as it is needed by the configuration sync process. After adding this to the controller I could push the configuration to the controller.
Second problem - failed to add the first WLAN from the backup as I have added the temporary dummy W LAN via the wizard and NCS reported a conflict. So had to delete WLAN ID 1 from the WLC GUI directly and then the config push no longer reported this error.
Third problem - for some reason did not add the TACACS server details - reported the error that it could not added them. I manually added these via a template via NCS and all was well.
Fourth problem - all but the first WLAN was in the disabled state - had to re-enable all of the WLANs.
Fifth problem - any default items I had disabled or removed have not been saved - therefore I have removed the public and private SNMP communities - but these were still on the WLC after the restore. I have disabled unused ports not in the LAG as they show an error in NCS - these where not disabled after the restore.
So all in all not a very satisfactory restore process from NCS to an defaulted WLC ( meant to simulate to the customer what would be needed if they had to replace a controller due to hardware failure ).
Cisco :: Restore 5.2.148.0 Backup File On Different Server Running WCS?
Feb 10, 2011If the hostnames are the same - can I restore the backup file from a wcs 5.2.148.0 instance on a different wcs instance running wcs 6.0.196.0?
View 1 Replies View RelatedCisco :: Backup And Restore Quarantines Ironport C170
Dec 20, 2011Is there anyway to backup and restore the spams quarantine to another ironport c170?
View 1 Replies View RelatedCisco Wireless :: 6513 - How To Access Memory On WISM To Delete Old Boot Image
Sep 22, 2012I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
Linksys Cable / DSL :: WAG160N Cannot Restore Configuration Backup
Mar 27, 2010I have a WAG160N and its seems to have reset to factory defaults, no idea why, but when trying to restore the Configuration Backup all I get is "Restore Failure <Unmatched pid>"
View 2 Replies View RelatedCisco Routers :: RVS4000 - Will Config Backup From V1 Restore To V2 Properly
Jun 3, 2012I'm replacing an older (& failing) RVS4000 v1 with a new V2. I need to minimize downtime. Will a config backup from the old v1 restore properly to a new v2 (all have newest firmware)? There are a lot of tweaks including several VPNs and to do it all manually is not desirable.
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS5.2 Backup And Restore On A Different Software Version?
Oct 3, 2011We are trying to make a restore from the backup done on ACS version 5.1 to a new appliance running ACS5.2 Before doing it I found this note in Cisco ACS user guide:
Note: You cannot back up data from an earlier version of ACS and restore it to a later version. Backup and restore must be performed on the same version of ACS. If you need the data on a different version of the ACS, you can perform an upgrade after you restore the data. Refer to the Installation and Setup Guide for Cisco Secure Access Control System 5.1 for more information on upgrading ACS to later versions.
How should I understand it? This note has conflicting statements. We can't restore to a later version but if you need data on a different version of ACS you can perform an upgrade AFTER YOU RESTORE the data. Doesn't it mean that the restore will still work? How would I do the upgrade to version 5.2 or even version 5.3 that was announced to be released very soon? I didn't find anything on the software upgrade in ACS5.1 guide.
Cisco Routers :: Moving From Faulty SRP527 To SRP 547 - Restore From Backup?
May 8, 2012I'm trying to move from a faulty SRP527 to SRP 547 - I tried a Restore from Backup, but it doesn't work.So start from fresh, and I'm having an issue trying to add a 2nd SSID to a VLAN...
I keep getting the error:
"FAILED! SSID 2 has joined another VLAN"
Except it hasn't... its not assigned to any VLAN...
Cisco Switching/Routing :: Stacking 3750-X With Universal Image With 3750-G Running BIN Image?
Oct 10, 2011I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedCisco :: How To Restore ACS Config From An Existing Backup File In ACS Cluster Deployment
May 21, 2012How can we restore ACS config from an existing backup file, in an ACS cluster deployment? is it through CLI? with"restore"or"acs restore" command? and should I restore only the ACS config or both ACS and ADE-OS config?
View 4 Replies View RelatedCisco :: How To Make Simple Backup / Restore Running Config Jobs On LMS 4.1
Oct 20, 2011have some problems with setting up jobs for the backup running config on my switches. Have RW and RO contact with everyone and can change the config in editor, but do not get config.txt
View 1 Replies View RelatedCisco Firewall :: Cannot Access FWSM Via Session Command In 6513 (VSS Enabled)
Apr 24, 2012Today i received FWSM from cisco (RMA), I need to configure it as standby unit for existing FWSM active/standby setup.
IOS on RMAed FWSM is 2.3.4 and cisco VSS supports FWSM IOS 4.0.4 and later.My issue is, I cannot access FWSM (IOS 2.3.4) via session command from cisco 6513 but could successfully consoled it without any problem. I have reloaded it twice and also tried to disable and enable power on it.
VSS#sh module switch 2
Switch Number: 2 Role: Virtual Switch Standby
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 6 Firewall Module WS-SVC-FWM-1 -----------
[code]....
why I cannot access FWSM through session command ?Whether this is because of older IOS ? If yes then how to upgrade its IOS ?Is it possible to upgrade IOS via FWSM console ? if yes, Do i need to test on different slot ?
Cisco :: 3725 IOS Image That Supports The Ip Sla Command?
Oct 19, 2012any 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 Replies View RelatedCisco Wireless :: 5500 How To Reboot Controller To Use Backup Recovery Image
Jun 22, 2012I have 5500 controller with firmware 7.0 installed from the factory. Due to some reasons, I understood that other existing wireless infrastructure runs on firmware 6.0, and hance i need to downgrade the 5500 series to 6.0 . During the bootup, i could see there is another image called backup recovery image, which is running on version 6.0. How can i reboot controller to use the older image , which is from backup recovery image. I couldnt find it in the configuration guide.
View 4 Replies View RelatedCisco Switching/Routing :: 6513 - SSO Functionality
Jan 31, 2012Well I have been back and forth on this a while now...I have a 6513E chassis that is getting prepped for prod. I am currently testing sso functionality and I can only get it to work using the following images on both Sup Cards.
s72033-adventerprise_wan-mz.122-33.SXI5.bin
If I try any other image, smaller or bigger in size...it forces my Sup card in mod 8 to recycle " proxy request from peer ". I have tried K9 images and non K9 images. Here is an output from sh redundancy.
Redundant System Information : Available system up time = 4 minutes Switch overs system experienced = 0 Standby failures = 0 Last switchover reason = none [code]...
Cisco Switching/Routing :: 6513 CatOS Config To IOS
Jul 31, 2012I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I need to pull the running config from the CatOS chassis and make it work on the IOS chassis. i can do this manually but was wondering if there are any trade secrets on doing this.
View 3 Replies View RelatedCisco Switching/Routing :: Unable To Console / Ssh To 6513
Aug 9, 2012I have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies View RelatedCisco Switching/Routing :: 6513 / 6509 E - EOL Notices
Apr 18, 2013Are there any EOL notices out for the Catalyst 6513, 6509 etc E chassis? I cant find anything on the internet for the E variant, so assume this hasn't had a notice published yet.
View 2 Replies View RelatedCisco Switching/Routing :: VSS Configuration On 6513 Switches
Mar 10, 2013My question is regarding VSS configuration on Cisco 6513 switches. My understanding is that the hardware and software configuration on the devices must be exactly the same for the VSS to function correctly. Do the Bootstrap versions also have to be identical?
The production switch is running Bootstrap Version 12.2(17r)SX5, while the new switch is running Bootstrap Version 12.2(17r)SX7.
Cisco Switching/Routing :: Catalyst 6513 NAM Module
Aug 24, 2012i have a cisco Netowtk Analysis module installed on a 6513 core switch which is NAM-1, the version on the NAM is 5.1 and we need to upgrade to the latest version which is 5.1(2)
View 1 Replies View RelatedCisco Switching/Routing :: Restore 881-SEC-K9 Factory Startup Configuration?
May 21, 2012I messed up the IOS on the flash of CISCO881-SEC-K9. On reboot it booted to ROMMON which allowed me to tftp up a working IOS c880data-universalk9-mz.151-4.M3.bin. Unfortunately somewhere in my playing around the default startup configuration factory loaded on the routerhas been erased. I can load a new a config on the device but as I'm using the router to learn its useful to have the original config load when I factory reset the device. What is the factory start up config?
View 3 Replies View Related