any 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 RepliesI need to know the command to take the Backup and Restore of IOS Image of 6513 through tftp server.
View 6 Replies View RelatedI'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedI'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedI am a traffic shaping newcomer and need some guidance as how to BEGIN to approach a problem with traffic. We have been rolling out Windows 7 at sites and the additional traffic it causes on installation is considerable as it has to request information from our central site to populate My Documents and Outlook mailboxes.This has caused some problems on sites as there traffic rates increase to the point that QoS is not sufficient to protect voice traffic and delays and one-way audio are being experienced.One question is this - is GTS a solution or is CBWFQ within GTS the solution or is something else preferable? The sites involved are data/voice with a variety of routers.Second question is this - if we have a remote site with a 3725 router as the WAN aggregator with one 4506/Sup IV and one Cat 3550-24-PWR the shaping should be best placed on the 3725, correct? Also, are there issues with shaping incoming/outgoing traffic as I seem to have read?FYI, the 3725 router has 12.4(8d) with IP VOICE/NO CRYPTO IOS version. The 4506 has 12.1(23)E4 with basic L3 feature set.
View 1 Replies View RelatedI have a 3725 router and would like to upgrade the slot:0 compact flash to a higher capacity. My question is, I can just pick up a 4GB compact flash card from walmart, or do I have to have a card from Cisco?
View 2 Replies View RelatedI'm trying to bring up two t1 and bundle them into a multilink on a 3845 on one end and a 3725 on the other end. On the 3845 I have installed two VWIC-2MFT-T1-DI and on the 3725 I have installed two VWIC-2MFT-T1 and a 1DSU/CSU-T1-V2.
For some reason I'm able to bring up the T1's on the DSU/CSU WIC. When I try to connect the T1 on the other WICs, on the 3845 I see SLIPs and Interface Resets however on the 3725 there is no errors however I still see UP DOWN.
CONFIG 3845
controller T1 2/0/0
framing esf
linecode b8zs
cablelength short 133
channel-group 0 timeslots 1-24 speed 64
[code]....
I am implementing traffic export on the WAN interface of my 3725 router. I use a dialer interface for PPPoE which is applied to the Fa0/0 interface. This dialer WAN interface has Zone Based Firewall, NAT Outside, ACLs applied to it, as well as IP Traffic Export for an IPS. In what order would each of these items process a packet? In other words, is the order something like ZBF, ACL, IP Traffic Export, then NAT? How would QoS fit into something like this as well? I am asking because I am wondering how much processing the packets receive before they are mirrored over to my IPS.
View 1 Replies View Related I have a Cisco 3725 router with IOS version "Cisco IOS Software, 3700 Software (C3725-ADVIPSERVICESK9-M), Version 12.4(12)". And this router is serving as a CE route for our MPLS connection to the service Provider. We do also have multiple VRFs ( around 10) and the WAN interface is DS3. So we created point-to-point subinterfaces and we put them in different vrfs. We have now transitioned to a new ISP and the ISP requested us to mark all of our outgoing traffics with DSCP AF31. So I have created the following policy-map
policy-map TRAFFIC-OUT-WAN-AF31
class TRAFFIC-OUT-WAN
set ip dscp af31
class-map match-any TRAFFIC-OUT-WAN
match any
Now we do have multiple GRE tunnel interfaces sourced from one of the WAN subinterface ( which is a member of VRF A). So the moment I applied the the policy-map on this WAN sub-interface (using the syntax "service-policy out TRAFFIC-OUT-WAN-AF31"), most of the GRE tunnels went down. And there is eBGP running on top of these GRE tunnels.
I work for an ISP and we are currently bonding 5x 6Mb ADSL connections for use as a wireless backhaul. We are currently using a Cisco 3725 and bonding the links via MLPPP. This set up is working fine except that we are not getting the full 30Mb on the download side. We are seeing more like 18 to 20. I am wondering if we can acheive the full speed with our current set up or will we need something different to get the job done.
View 1 Replies View RelatedI'm trying to migrate the running-config from our old 3725 router to our new 3945e router. Almost all of the config is copied over except for a few lines that come up as unrecongnized commands. So it looks like these commands were either removed or changed to something new.
View 12 Replies View RelatedI have been using a route map to pick WAN exit points (PBR) on a 3725 router. This have been working fine with /24 networks. I am trying to pick the first /28 piece out of the 10.1.1.0 network and send it out a different exit from the rest of that network. I have tried the /28 entry at the start and end of the route map, although I thought the first match would stop any further route map processing. The entry does not seem to have any effect, as traffic from all addresses in the 10.1.1.0 /24 network exit per the "route-map 10-LAN permit 11" section.
access-list 5 remark Ten Dot 1 low 63 IPs
access-list 5 remark SDM_ACL Category=2access-list 5 remark Ten Dot One Low 63 IPs access-list 5 permit 10.1.1.0 0.0.0.63 log
[ code]....
Cisco 3725
IOS: (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T9
Wireless Module NME
Brief current running config below:
interface FastEthernet0/0
description WAN LINK
bandwidth 8192
[Code].....
I have a 3725 routeur configured to receive the PPP/ATM/DSL connexion of our customer. I have found that the routeur has created 1035 virtual-access (1035 is his max) but I only have 85 customer on this router
View 1 Replies View RelatedI have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
I am setting up multiple vlan interfaces on a pair of HSRP Routers that will provide layer 3 routing for a network. I am seeing this command sporadically show up in the router config mac-address-table static 0000.0c07.acd2 vlan 210
I am not entering this command. So far, it has not shown up on the companion 3725 router. I have a 2nd vlan I have just created and the problem hasn't shown up for that vlan as yet.Using C3725-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3) on the routers.
I have a 3725 router that is reporting the following syslog message:
%FAN-3-FAN_FAILED: Fans had a rotation error reported.
When I do a show environment all, I am getting the following message:
Fan status: Warning- low fan rpm condition detected.
Both the the fans are functional and are rotating fine. How do I repair?
I seem to be having a problem with DNS name resolution after configuring my router (Cisco 3725 running IOS image: c3725-adventerprisek9-mz.124-25.bin) for handling DHCP requests.
Before I made the change, everything was working correctly; I could ping Google.com from a computer inside my LAN and would get response from one of Google's public IP's like normal.
I had a separate DHCP/DNS server running Windows Server 2008 handling the DHCP request and DNS queries.
When I made the change, I turned off the DHCP/DNS server and issued the following DHCP commands to my router:
Code...
I'm trying to configure a SPAN session on a Cisco 3725 router, but it won't let me complete the command. The router has two Fast Ethernet interfaces: 0/0 and 0/1. I'm trying to configure a SPAN session with Fa0/0 as the source interface and Fa0/1 as the destination interface. [code] But when I try to configure the session, it seems like it's giving me the option to configure the SPAN session, but in the end the router won't let me: [code] When I type "?", why would it give me the option of using the Fast Ethernet interface as source port, then when I try to execute the command, it doesn't like it?
View 7 Replies View RelatedI read that there are internal and external flash memory in 3725 router that can max up to 128mb. So adding the sizes of internal and external flash memory, will that total to 256mb?
And also is the internal flash of 3725 just the same with its external flash?
I had the 2 circuits go down at the same time from our ISP and I had to power cycle the router and when it came back up I went from VA # 2 to now VA 3#....I know what is what but it is confusing for my counterpart and I can not remove the old entry for VA#1 and VA#2. [code]
View 3 Replies View RelatedI'm developing a project where I use the SNMP protocol to discover the network. By discovering the network I mean go through all the routers and switches and retrieve the IP routing table from routers and the forwarding table from switches. With the routers I have no problem. For the switches I need to know for each port the MAC addresses and the Vlans. Basically it's use SNMP to find a port number from a MAC address. To do that i followed this tutorial: [URL]
The problem is that I'm using a Cisco 3725 Router with IOS 12.4 (21) and a NM-16ESW module to work as a Switch and when I use the OID .1.3.6.1.2.1.17 corresponding to the BRIDGE-MIB as it follows:
snmpwalk -v2c -c myrouter 10.1.1.5 .1.3.6.1.2.1.17
it returns:
SNMPv2-SMI::mib-2.17.1.1.0 = Hex-STRING: 00 00 00 00 00 00
SNMPv2-SMI::mib-2.17.1.2.0 = INTEGER: 0
SNMPv2-SMI::mib-2.17.1.3.0 = INTEGER: 4
From this I guess there's no information on the router about Vlans or anything. Other thing is that when I use community string indexing it returns a timeout. My theory is that this version doesn't support indexing but I don't know.
how can I get the Port Number from a MAC address from this "switch" (it's a router working as a switch) using SNMP?
I have a Cisco 3725 running IOS 12.3. I have three WAN connections (2 x 100Mb and 1 x 2Mb serial) and I need to replace the 2Mb serial connection with a further 100Mb connection. However, I have not got any spare 100Mb sockets.My plan is to use a switch that supports VLANs, connect the three WAN connections to the switch, each in their own VLAN, then connect the switch to one port on the router, configuring the switch port as a trunk (so that it passes all three VLANs across the link) and configuring the router so that for that single Ethernet interface, it has three subinterfaces each configured for a VLAN that matches the VLAN used for the corresponding WAN connection.
I am a bit rusty on my IOS so I wanted to run this all past the community for feedback. [code] Any thoughts on whether or not that will work? Are there any commands from the original interface configurations that I CANNOT use when moving them to a subinterface? I'm thinking that the speed & duplex commands need to be removed?
Is Ciscoworks LMS 3.2 supports WISM 2?
View 3 Replies View RelatedWhich version of IOS for the 2621 supports NAT?
View 1 Replies View Relatedthe max amount of AP's one 5508 WLC can support ?
View 4 Replies View RelatedImagine on a 3845 router, I need to bond 2xDS1 circuits (for a Metro Private Line, point-to-point circuit). I have done that multiple times for NxT1s with MLPPP - OK.So my question is, is the card below and MLPPP valid for 2xDS1? I read all the product specification and it always mention "T1", but it does not officially say I can configure DS1.VWIC-2MFT-T1-DI#Two-port RJ-48 multiflex trunk - T1 with drop and insert
View 1 Replies View RelatedI have 2611xm router with 2 fastethernet ports. Now I want to install NM-1FX-TX module. I just want to conform that does 2611 supports NM-1FX-TX module. I am using this device for lab purpose. I am using latest IOS"
View 2 Replies View RelatedI am interesting is ESW-520-24-K9 switch supports GLC-LH-SM SFP? In official data sheet there is no information about that. it is supported and I am interesting if it is true ?
View 5 Replies View RelatedWe are using Cisco 1941 Router as CPE where we wanted to trap CPU, Memory & ISYSTEM MIB. The same we are achiveing using SNMPV2 but when we tried using SNMPV3, there is no response for these MIBs.
We tried to configure SNMPV3 using below Link but still there was issue. There was response fr [URL]
Wanetd to know SNMPV3 MIB are supported for Cisco 1941 Router IOS Code universalk 15.2(3)T1 & Data License. When we tried using Cisco IOS MIB Locator, we are not able to see any MIB for SNMPV3. whats is that mean. Does this Platform + IOS Support SNMPV3 or not.
Below is the Snapshot from Cisco IOS MIB Locator for said image.
[Code]......
I have a small network of about 12 Mac's running OS X, about 20 or so iOS devices and a OS X Server. Currently i have a Cisco SRP547W which works fine when we're all wired in, however we have connection issues when trying to access the server over Wi-Fi. I'm lead to believe that this could be a result of the lack of support for Bonjour within the router. What might be a solid alternative?
View 1 Replies View RelatedWe have a 10 MB Internet Link coming from our ISP through there MUX.The link is connected to our Router 1841.Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)From past few weeks we are facing link speed issues. It gives not more then 1-2 MB.The ISP is telling there is no Problem in there network. We have kept Default Routing pointing towards there IP.We want to know whether our router will support 10MB Internet Link or Not.
View 9 Replies View RelatedWe are using the Cisco ACS 5.2 for AAA to manage our network devices. We plan to migrate all our edge's devices to IPv6 soon. Can or when the Cisco ACS 5 support IPv6 address?
View 1 Replies View Related