I have a 3725 routeur configured to receive the PPP/ATM/DSL connexion of our customer. I have found that the routeur has created 1035 virtual-access (1035 is his max) but I only have 85 customer on this router
View 1 Replies
I had the 2 circuits go down at the same time from our ISP and I had to power cycle the router and when it came back up I went from VA # 2 to now VA 3#....I know what is what but it is confusing for my counterpart and I can not remove the old entry for VA#1 and VA#2. [code]
View 3 Replies View RelatedI'm having iball laptop with LAN connectivity in Windows XP Service Pack 3. I found out how to create hotspot on laptop and tried it.Everything gone fine, network is showing up in my Ipod Touch too. But even after connecting to this network,I cannot access internet!Then I checked in Network Connections that both LAN & Wireless Connections are connected,but in Wireless Connection when checked in status the packets are sending but not receiving.This is how it shows with the command "ipconfig"....
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and Settingsadmin>ipconfig
Windows IP Configuration
Ethernet adapter Wireless Network Connection:[code.....]
I am trying to unravel a ASA 5550 config that has been created over several years, by multiple people, some who used ADSM, some who used CLI.
None of them ever removed any lines from the configuration, and none did any documentation. When examining the actual configuration from a CLI perspective:
1. Does an ADSM- created access list end with any specific ADSM- added suffix?
2. When ANY access list is created in an ASA 5550, does it HAVE to be included in the access-group command to be functional? Can it also be functional if referenced in a "nat" command?
3. If the access list does meet either of the criteria specified in question #2, is it completely non-functional?
4. If an access list is applied to a logical or physical port that is shut down, is the access list functional?
Yesterday, I configured ASA via CLI for Static PAT and created some entries in an access-list. I will be testing that setup this evening.
However on a quick double check of the settings on the device via ASDM I could not see the acess-list settings. I searched every tab and found nothing so I PuTTYed into the device and checked the running config. The rules I created were right there. Is this something I should expect? If so doesn't it defeat the point of having a GUI if it does not show a complete running config?
I have 6513 which have wism and sup 720 , for some reason the access points keeps on going up and down the port channels created automatically but i cannot see any configuration inside it as shown below .I tried to edit the interfaces and add the trunk configuration but it cannot be modified . [code] the Wism status is showing up but the APs Number regestered keeps on going up and down the version running on the sup 720 is 12.2(33)SXI5 and the wism is installed in slot 9.
View 5 Replies View RelatedI'm trying to migrate the running-config from our old 3725 router to our new 3945e router. Almost all of the config is copied over except for a few lines that come up as unrecongnized commands. So it looks like these commands were either removed or changed to something new.
View 12 Replies View RelatedIm currently connected to a remote acess vpn setup using the vpn client and am unable to get anywhere around my network, this normalyl works fine The only difference i can see is that the are multiple virtualaccess interfaces pointing to my public ip address, which im presuming is causing routing issues How can i clear these unsed virtual access lines and how can i make it forget them automatically after disconnects?
View 5 Replies View RelatedI am setting up multiple vlan interfaces on a pair of HSRP Routers that will provide layer 3 routing for a network. I am seeing this command sporadically show up in the router config mac-address-table static 0000.0c07.acd2 vlan 210
I am not entering this command. So far, it has not shown up on the companion 3725 router. I have a 2nd vlan I have just created and the problem hasn't shown up for that vlan as yet.Using C3725-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3) on the routers.
I have a 3725 router that is reporting the following syslog message:
%FAN-3-FAN_FAILED: Fans had a rotation error reported.
When I do a show environment all, I am getting the following message:
Fan status: Warning- low fan rpm condition detected.
Both the the fans are functional and are rotating fine. How do I repair?
I read that there are internal and external flash memory in 3725 router that can max up to 128mb. So adding the sizes of internal and external flash memory, will that total to 256mb?
And also is the internal flash of 3725 just the same with its external flash?
We have a dsl connection on 897 dsl router at the customers HO.The telephone line is directly connected to router we configured dialer with username and password and it takes a static ip of 212.249.213.xxx.Now he has some branches that are connected through wireless links and he has arranged for a subnet of 8 public IP's in the range 72.70.245.xxx
Can we some how use these public ip's as secondary in the routers dialer interface and assign to the servers in the branches so that it can be accessed through web.
I have a problem in my Cisco 1841 in Virtual-Access Interface all interfaces is UP Except Virtual Access is Down . [code]
when i want recover the virtual access to up ,should i do shut & no shut to the ATM interface.What is the cause of the problem, and how I can solve this issue?
I wish to access my virtual pc remotely, As i have downloaded OTRS ticketing system on a virtual machine and i wish to access it remotely. The physical server IP is 62.84.xx.xx the Virtual server IP is 10.0......"check link below please"
View 2 Replies View RelatedWe have a 3745 LNS router, currently there are less number of users connected.when a user dials request authenticated and one virtual-access interface is formed in LNS router.Now the user is disconnected the vpn and connected to VPN again in this case, whether the user is connected to the same virtual-access interface which was assigned before disconnecting or different virtual-access interface is created.
View 0 Replies View RelatedI recently installed VMplayer on my Win 7 machine, and I installed Win XP on the VM. So far everything seems to work fine. However, on my home network I have a Linksys NSLU2 mini network server which has a flash drive plugged in that contains my files that I access from any of my home PC's. No problem accessing it from the Win 7 machine, but when I try to setup a "new network place" on the XP system, I get an error telling me that the address is not valid.
View 8 Replies View RelatedRegion : Others
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0
ISP :
My router is TDW8961ND
The firmware version is 3.0.0
The hardware version is 3.0
I am trying to have a virtual http server at port 80 but when I do this and save, I get this message: "Notice: The WAN HTTP port of CPE will be chaged to 8080 if submit successfully."Then after that I cannot access the server at port 80.
I am a traffic shaping newcomer and need some guidance as how to BEGIN to approach a problem with traffic. We have been rolling out Windows 7 at sites and the additional traffic it causes on installation is considerable as it has to request information from our central site to populate My Documents and Outlook mailboxes.This has caused some problems on sites as there traffic rates increase to the point that QoS is not sufficient to protect voice traffic and delays and one-way audio are being experienced.One question is this - is GTS a solution or is CBWFQ within GTS the solution or is something else preferable? The sites involved are data/voice with a variety of routers.Second question is this - if we have a remote site with a 3725 router as the WAN aggregator with one 4506/Sup IV and one Cat 3550-24-PWR the shaping should be best placed on the 3725, correct? Also, are there issues with shaping incoming/outgoing traffic as I seem to have read?FYI, the 3725 router has 12.4(8d) with IP VOICE/NO CRYPTO IOS version. The 4506 has 12.1(23)E4 with basic L3 feature set.
View 1 Replies View RelatedI have a 3725 router and would like to upgrade the slot:0 compact flash to a higher capacity. My question is, I can just pick up a 4GB compact flash card from walmart, or do I have to have a card from Cisco?
View 2 Replies View Relatedany 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 Replies View RelatedI'm trying to bring up two t1 and bundle them into a multilink on a 3845 on one end and a 3725 on the other end. On the 3845 I have installed two VWIC-2MFT-T1-DI and on the 3725 I have installed two VWIC-2MFT-T1 and a 1DSU/CSU-T1-V2.
For some reason I'm able to bring up the T1's on the DSU/CSU WIC. When I try to connect the T1 on the other WICs, on the 3845 I see SLIPs and Interface Resets however on the 3725 there is no errors however I still see UP DOWN.
CONFIG 3845
controller T1 2/0/0
framing esf
linecode b8zs
cablelength short 133
channel-group 0 timeslots 1-24 speed 64
[code]....
I am implementing traffic export on the WAN interface of my 3725 router. I use a dialer interface for PPPoE which is applied to the Fa0/0 interface. This dialer WAN interface has Zone Based Firewall, NAT Outside, ACLs applied to it, as well as IP Traffic Export for an IPS. In what order would each of these items process a packet? In other words, is the order something like ZBF, ACL, IP Traffic Export, then NAT? How would QoS fit into something like this as well? I am asking because I am wondering how much processing the packets receive before they are mirrored over to my IPS.
View 1 Replies View Related I have a Cisco 3725 router with IOS version "Cisco IOS Software, 3700 Software (C3725-ADVIPSERVICESK9-M), Version 12.4(12)". And this router is serving as a CE route for our MPLS connection to the service Provider. We do also have multiple VRFs ( around 10) and the WAN interface is DS3. So we created point-to-point subinterfaces and we put them in different vrfs. We have now transitioned to a new ISP and the ISP requested us to mark all of our outgoing traffics with DSCP AF31. So I have created the following policy-map
policy-map TRAFFIC-OUT-WAN-AF31
class TRAFFIC-OUT-WAN
set ip dscp af31
class-map match-any TRAFFIC-OUT-WAN
match any
Now we do have multiple GRE tunnel interfaces sourced from one of the WAN subinterface ( which is a member of VRF A). So the moment I applied the the policy-map on this WAN sub-interface (using the syntax "service-policy out TRAFFIC-OUT-WAN-AF31"), most of the GRE tunnels went down. And there is eBGP running on top of these GRE tunnels.
I work for an ISP and we are currently bonding 5x 6Mb ADSL connections for use as a wireless backhaul. We are currently using a Cisco 3725 and bonding the links via MLPPP. This set up is working fine except that we are not getting the full 30Mb on the download side. We are seeing more like 18 to 20. I am wondering if we can acheive the full speed with our current set up or will we need something different to get the job done.
View 1 Replies View RelatedI have been using a route map to pick WAN exit points (PBR) on a 3725 router. This have been working fine with /24 networks. I am trying to pick the first /28 piece out of the 10.1.1.0 network and send it out a different exit from the rest of that network. I have tried the /28 entry at the start and end of the route map, although I thought the first match would stop any further route map processing. The entry does not seem to have any effect, as traffic from all addresses in the 10.1.1.0 /24 network exit per the "route-map 10-LAN permit 11" section.
access-list 5 remark Ten Dot 1 low 63 IPs
access-list 5 remark SDM_ACL Category=2access-list 5 remark Ten Dot One Low 63 IPs access-list 5 permit 10.1.1.0 0.0.0.63 log
[ code]....
Cisco 3725
IOS: (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T9
Wireless Module NME
Brief current running config below:
interface FastEthernet0/0
description WAN LINK
bandwidth 8192
[Code].....
I have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
I seem to be having a problem with DNS name resolution after configuring my router (Cisco 3725 running IOS image: c3725-adventerprisek9-mz.124-25.bin) for handling DHCP requests.
Before I made the change, everything was working correctly; I could ping Google.com from a computer inside my LAN and would get response from one of Google's public IP's like normal.
I had a separate DHCP/DNS server running Windows Server 2008 handling the DHCP request and DNS queries.
When I made the change, I turned off the DHCP/DNS server and issued the following DHCP commands to my router:
Code...
I'm trying to configure a SPAN session on a Cisco 3725 router, but it won't let me complete the command. The router has two Fast Ethernet interfaces: 0/0 and 0/1. I'm trying to configure a SPAN session with Fa0/0 as the source interface and Fa0/1 as the destination interface. [code] But when I try to configure the session, it seems like it's giving me the option to configure the SPAN session, but in the end the router won't let me: [code] When I type "?", why would it give me the option of using the Fast Ethernet interface as source port, then when I try to execute the command, it doesn't like it?
View 7 Replies View RelatedI'm developing a project where I use the SNMP protocol to discover the network. By discovering the network I mean go through all the routers and switches and retrieve the IP routing table from routers and the forwarding table from switches. With the routers I have no problem. For the switches I need to know for each port the MAC addresses and the Vlans. Basically it's use SNMP to find a port number from a MAC address. To do that i followed this tutorial: [URL]
The problem is that I'm using a Cisco 3725 Router with IOS 12.4 (21) and a NM-16ESW module to work as a Switch and when I use the OID .1.3.6.1.2.1.17 corresponding to the BRIDGE-MIB as it follows:
snmpwalk -v2c -c myrouter 10.1.1.5 .1.3.6.1.2.1.17
it returns:
SNMPv2-SMI::mib-2.17.1.1.0 = Hex-STRING: 00 00 00 00 00 00
SNMPv2-SMI::mib-2.17.1.2.0 = INTEGER: 0
SNMPv2-SMI::mib-2.17.1.3.0 = INTEGER: 4
From this I guess there's no information on the router about Vlans or anything. Other thing is that when I use community string indexing it returns a timeout. My theory is that this version doesn't support indexing but I don't know.
how can I get the Port Number from a MAC address from this "switch" (it's a router working as a switch) using SNMP?
Did any know that how many AP Groups can be created by one Controller? (5508) May I have 100 AP Groups?
View 3 Replies View RelatedI have 3 Twitter accounts that all work fine on my iphone and my sony experia phone but I can not get into twitter on my home cpu because I cant find the email address that I used to start the account i tell them i lost it so they email it to my email address on file that they wont share. So I need to find out every single email account i have set up in the last 2 years.How do i do that? I tried the option to security to optioms again and nothing for twitter. I need those account on my desk so i can send photos off my hard drive.
View 1 Replies View RelatedRestoring a BARS file created from one server onto a different server?
View 6 Replies View Related
