Cisco WAN :: 3725 / Marking A Traffic With AF31
May 29, 2012
I have a Cisco 3725 router with IOS version "Cisco IOS Software, 3700 Software (C3725-ADVIPSERVICESK9-M), Version 12.4(12)". And this router is serving as a CE route for our MPLS connection to the service Provider. We do also have multiple VRFs ( around 10) and the WAN interface is DS3. So we created point-to-point subinterfaces and we put them in different vrfs. We have now transitioned to a new ISP and the ISP requested us to mark all of our outgoing traffics with DSCP AF31. So I have created the following policy-map
policy-map TRAFFIC-OUT-WAN-AF31
class TRAFFIC-OUT-WAN
set ip dscp af31
class-map match-any TRAFFIC-OUT-WAN
match any
Now we do have multiple GRE tunnel interfaces sourced from one of the WAN subinterface ( which is a member of VRF A). So the moment I applied the the policy-map on this WAN sub-interface (using the syntax "service-policy out TRAFFIC-OUT-WAN-AF31"), most of the GRE tunnels went down. And there is eBGP running on top of these GRE tunnels.
View 5 Replies
ADVERTISEMENT
Nov 25, 2012
I want to mark traffic on Cisco 3020 switch entering to interface gigabitEthernet 0/1 ingress direction with DSCP values. interface gigabitEthernet 0/1 is in access mode and in vlan 10.
This is my config:
access-list 1 permit host 10.10.1.1
class-map match-all ipclass1
match access-group 1
[Code].....
View 2 Replies
View Related
Mar 15, 2011
I am a traffic shaping newcomer and need some guidance as how to BEGIN to approach a problem with traffic. We have been rolling out Windows 7 at sites and the additional traffic it causes on installation is considerable as it has to request information from our central site to populate My Documents and Outlook mailboxes.This has caused some problems on sites as there traffic rates increase to the point that QoS is not sufficient to protect voice traffic and delays and one-way audio are being experienced.One question is this - is GTS a solution or is CBWFQ within GTS the solution or is something else preferable? The sites involved are data/voice with a variety of routers.Second question is this - if we have a remote site with a 3725 router as the WAN aggregator with one 4506/Sup IV and one Cat 3550-24-PWR the shaping should be best placed on the 3725, correct? Also, are there issues with shaping incoming/outgoing traffic as I seem to have read?FYI, the 3725 router has 12.4(8d) with IP VOICE/NO CRYPTO IOS version. The 4506 has 12.1(23)E4 with basic L3 feature set.
View 1 Replies
View Related
Feb 6, 2013
in switch 2960s ( c2960s-universalk9-mz.122-55.SE5 ) , i want to marking the traffic between two hosts (Data replication), i choose to use " mac access-list" to classify my trafic before apply the policy marking . but did'nt work . c
! my mac ACL
mac access-list extended test
permit host 000a.1a41.aa52 host 000a.1a41.1bc2
!
class-map match-all test
match access-group name test
[code]....
View 4 Replies
View Related
Dec 3, 2011
I am wondering what is the TOS value equivalent to DSCP value AF31? I am wondering what is the TOS value equivalent to DSCP value AF31?I have tried to use the charts but I couldn’t understand how to convert it.
View 5 Replies
View Related
Oct 12, 2012
i'm doing B.E., final year.My project is IP TRACEBACK.so we hav to mark packets in router.Is it possibe to mark packet in cisco packet tracer?
View 1 Replies
View Related
May 17, 2011
1) which DSCP marking to use for ex90s(HD video)?
2) as a test we are planning do to deploy ex90 at few of locations. at location 1 we will do DSCP EF marking while at the other location we will do DSCP AF41 for video..assume, LOC1 calls LOC2: so, when video traffic from LOC1 arrives to LOC2 will it be marked as EF? and when traffic from LOC2 arrives LOC1 then traffic will be marked as AF41? if yes, then will there be any issue sometimes in case if we run out of bandwidth for EF?
View 2 Replies
View Related
Aug 22, 2011
I have a weird issue with a QOS policy that I have implemented. Details are below.
This is basically the policy I have created. It is running on a Cisco 877 router (running Advance IP Services 12.4). The internet connection is an Internode ADSL service.
class-map match-any VOIP
match access-group name VOICE-OUT
!
!
[Code]....
View 14 Replies
View Related
Nov 2, 2011
We have subscribed for MPLS links from Service provider we have a DC where the core connectivity is 90 MB and Remote branch location Connectivity is 64 Kbps. We are in process of enabling QOS for our links with co-ordination with Service provider ; as per our finding the branches have more RX traffic (downloading) so after discussion with provider we were advised to mark traffic from the core end and give it to the provider.The provider at its PE will honor the marking and set some B/W percentages and prioroty based on the DSCP marking values.
We need to mark this traffic so it is feasible to mark the traffic at the core DC router which has the below H/W details,Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.
Processor board ID 36161439
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.11
or is it feasible to mark the traffic at the core switch.
View 6 Replies
View Related
Jun 14, 2012
I am running 1.1.24 and spa303 phones I have a qos policy setup to mark all packets
The following is my qos
information 192.168.1.15/24
makring enabled
cos/DSCO DSCO
Value 0xb8
On my upstream device I only allow traffic that is marked with this dscp value. No traffic is coming through. RTP traffic is marked because it comes off the phone marked but I would expect the qos Policy so mark everything going to that ip space to be marked.
View 1 Replies
View Related
Feb 20, 2011
My new small router 866vae crashes and makes cold reboots every 20-30 minutes. I updated IOS, but it didn't work. The logs show texts like this:
Possible software fault. Upon reccurence,crashinfo, "show tech" and contact Cisco Technical Support. http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000!ip dns serverip nat inside source list 101 interface Dialer0 overload!dialer-list 1 protocol ip permitmac-address-table aging-time 15no cdp run!access-list 23 permit 192.168.1.0 0.0.0.255access-list 101 permit ip 192.168.1.0 0.0.0.255 anyaccess-list 111 permit udp any eq bootps any eq bootpcaccess-list 111 permit tcp any anyaccess-list 111 permit udp any anyaccess-list 111 permit icmp any any echo-replyaccess-list 111 permit icmp any any time-exceededaccess-list 111 permit icmp any any unreachableaccess-list 111 permit icmp any any administratively-prohibitedaccess-list 111 permit icmp any any echoaccess-list 111 permit gre any any!control-plane!!line con 0login localno modem enableline aux 0line vty 0 4access-class 23 inprivilege level 15login localtransport input telnet!scheduler allocate 60000 1000!end
View 10 Replies
View Related
Jul 21, 2012
i did on cisco 2960S switch at user ingress interface. but the marking is not showing in show policy-map interface gig 1/0/10 interface and ACL is not showing any match.
I also had a config reference from 2960S cisco guide.
access-list 103 permit tcp any any eq 80
access-list 104 permit tcp any any eq 23
access-list 105 permit icmp host 172.24.68.4 any
class-map IN_HTTP
match access-group 103
class-map IN_TELNET
match access-group 104(code)
View 1 Replies
View Related
Oct 9, 2011
anyway to implement priority marking on the voice packets on the IP communcicator which installed in a laptop (running Data VLAN in the switch)?
View 1 Replies
View Related
Jan 29, 2012
I have a pair of Nexus 7K's running 5.1(3). I have a handful of edge devices that I need to mark ingress traffic, and need to mark both DSCP and CoS. Right now, I have a working config that marks DSCP appropriately.While that works dor DSCP, the MQC will not allow me to mark both DSCP and COS in the same class, and unlike IOS, it appears that Nexus does not have a default DSCP-to-COS mapping. My understanding is this can be solved using table maps, but I don't see how that can solve my problem in this specific scenario (it appears I can do marking or table-map mutation, but not both?). How I can accomplish both?
View 5 Replies
View Related
Jun 8, 2013
I have a 3750G switch running 12.2(44)SE6 my customer has some Cisco EX90 and ex-Tandberg VC units connected to the switch in a dedicated VLAN 600. The switch is then connected to the WAN router which has its own VLAN 6
From sh mls qos interface x/x/x statistics I can see that the traffic is marked by the VC units as DSCP 34 however when I run this command on the interface to the CE router the marking has been lost.
Similarly in the opposite direction incoming from the CE router I can see the marking coming from across the MPLS ok but when I check the output to the VC unit the marking has been lost.
This would indicate that in the process of routing between VLAN's the DSCP marking has been lost.
how to correct this issue. Because my interfaces are in different VLAN's do I need to VLAN based QoS?
View 3 Replies
View Related
Aug 17, 2011
when using egress netflow (v9) and output marking.
The topologie : Server <-----> R1 1>-----<1 R2 2>----<2 R3
R2 is a 7200 with c7200p-adventerprisek9-mz.124-15.T11.bin What I'm doing :- R2 forwards ping packets from Server to R3. When they arrive on R2, icmp packets are marked with CS3
- I change the DSCP to CS4 on R2 before forwarding packet to R3. I'm using for that an output service-policy on the R2-2 interface like this : interface ATM2/0.36 point-to-point
ip address 192.168.1.1 255.255.255.252
ip flow ingress
ip flow egress
[Code]....
View 3 Replies
View Related
Sep 4, 2012
I have a 3725 router and would like to upgrade the slot:0 compact flash to a higher capacity. My question is, I can just pick up a 4GB compact flash card from walmart, or do I have to have a card from Cisco?
View 2 Replies
View Related
Oct 19, 2012
any 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 Replies
View Related
Jun 27, 2011
I'm trying to bring up two t1 and bundle them into a multilink on a 3845 on one end and a 3725 on the other end. On the 3845 I have installed two VWIC-2MFT-T1-DI and on the 3725 I have installed two VWIC-2MFT-T1 and a 1DSU/CSU-T1-V2.
For some reason I'm able to bring up the T1's on the DSU/CSU WIC. When I try to connect the T1 on the other WICs, on the 3845 I see SLIPs and Interface Resets however on the 3725 there is no errors however I still see UP DOWN.
CONFIG 3845
controller T1 2/0/0
framing esf
linecode b8zs
cablelength short 133
channel-group 0 timeslots 1-24 speed 64
[code]....
View 2 Replies
View Related
Nov 12, 2012
I am implementing traffic export on the WAN interface of my 3725 router. I use a dialer interface for PPPoE which is applied to the Fa0/0 interface. This dialer WAN interface has Zone Based Firewall, NAT Outside, ACLs applied to it, as well as IP Traffic Export for an IPS. In what order would each of these items process a packet? In other words, is the order something like ZBF, ACL, IP Traffic Export, then NAT? How would QoS fit into something like this as well? I am asking because I am wondering how much processing the packets receive before they are mirrored over to my IPS.
View 1 Replies
View Related
Aug 14, 2012
I work for an ISP and we are currently bonding 5x 6Mb ADSL connections for use as a wireless backhaul. We are currently using a Cisco 3725 and bonding the links via MLPPP. This set up is working fine except that we are not getting the full 30Mb on the download side. We are seeing more like 18 to 20. I am wondering if we can acheive the full speed with our current set up or will we need something different to get the job done.
View 1 Replies
View Related
May 30, 2013
I'm trying to migrate the running-config from our old 3725 router to our new 3945e router. Almost all of the config is copied over except for a few lines that come up as unrecongnized commands. So it looks like these commands were either removed or changed to something new.
View 12 Replies
View Related
Feb 2, 2011
I have been using a route map to pick WAN exit points (PBR) on a 3725 router. This have been working fine with /24 networks. I am trying to pick the first /28 piece out of the 10.1.1.0 network and send it out a different exit from the rest of that network. I have tried the /28 entry at the start and end of the route map, although I thought the first match would stop any further route map processing. The entry does not seem to have any effect, as traffic from all addresses in the 10.1.1.0 /24 network exit per the "route-map 10-LAN permit 11" section.
access-list 5 remark Ten Dot 1 low 63 IPs
access-list 5 remark SDM_ACL Category=2access-list 5 remark Ten Dot One Low 63 IPs access-list 5 permit 10.1.1.0 0.0.0.63 log
[ code]....
View 11 Replies
View Related
Jan 30, 2012
Cisco 3725
IOS: (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T9
Wireless Module NME
Brief current running config below:
interface FastEthernet0/0
description WAN LINK
bandwidth 8192
[Code].....
View 2 Replies
View Related
Mar 2, 2011
I have a 3725 routeur configured to receive the PPP/ATM/DSL connexion of our customer. I have found that the routeur has created 1035 virtual-access (1035 is his max) but I only have 85 customer on this router
View 1 Replies
View Related
Dec 26, 2011
I have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
View 1 Replies
View Related
Jun 4, 2012
I am setting up multiple vlan interfaces on a pair of HSRP Routers that will provide layer 3 routing for a network. I am seeing this command sporadically show up in the router config mac-address-table static 0000.0c07.acd2 vlan 210
I am not entering this command. So far, it has not shown up on the companion 3725 router. I have a 2nd vlan I have just created and the problem hasn't shown up for that vlan as yet.Using C3725-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3) on the routers.
View 4 Replies
View Related
Jan 14, 2008
I have a 3725 router that is reporting the following syslog message:
%FAN-3-FAN_FAILED: Fans had a rotation error reported.
When I do a show environment all, I am getting the following message:
Fan status: Warning- low fan rpm condition detected.
Both the the fans are functional and are rotating fine. How do I repair?
View 6 Replies
View Related
Jan 24, 2013
I seem to be having a problem with DNS name resolution after configuring my router (Cisco 3725 running IOS image: c3725-adventerprisek9-mz.124-25.bin) for handling DHCP requests.
Before I made the change, everything was working correctly; I could ping Google.com from a computer inside my LAN and would get response from one of Google's public IP's like normal.
I had a separate DHCP/DNS server running Windows Server 2008 handling the DHCP request and DNS queries.
When I made the change, I turned off the DHCP/DNS server and issued the following DHCP commands to my router:
Code...
View 5 Replies
View Related
Dec 12, 2012
I'm trying to configure a SPAN session on a Cisco 3725 router, but it won't let me complete the command. The router has two Fast Ethernet interfaces: 0/0 and 0/1. I'm trying to configure a SPAN session with Fa0/0 as the source interface and Fa0/1 as the destination interface. [code] But when I try to configure the session, it seems like it's giving me the option to configure the SPAN session, but in the end the router won't let me: [code] When I type "?", why would it give me the option of using the Fast Ethernet interface as source port, then when I try to execute the command, it doesn't like it?
View 7 Replies
View Related
Jan 24, 2012
I read that there are internal and external flash memory in 3725 router that can max up to 128mb. So adding the sizes of internal and external flash memory, will that total to 256mb?
And also is the internal flash of 3725 just the same with its external flash?
View 8 Replies
View Related
Sep 8, 2004
I had the 2 circuits go down at the same time from our ISP and I had to power cycle the router and when it came back up I went from VA # 2 to now VA 3#....I know what is what but it is confusing for my counterpart and I can not remove the old entry for VA#1 and VA#2. [code]
View 3 Replies
View Related
Dec 2, 2012
I'm developing a project where I use the SNMP protocol to discover the network. By discovering the network I mean go through all the routers and switches and retrieve the IP routing table from routers and the forwarding table from switches. With the routers I have no problem. For the switches I need to know for each port the MAC addresses and the Vlans. Basically it's use SNMP to find a port number from a MAC address. To do that i followed this tutorial: [URL]
The problem is that I'm using a Cisco 3725 Router with IOS 12.4 (21) and a NM-16ESW module to work as a Switch and when I use the OID .1.3.6.1.2.1.17 corresponding to the BRIDGE-MIB as it follows:
snmpwalk -v2c -c myrouter 10.1.1.5 .1.3.6.1.2.1.17
it returns:
SNMPv2-SMI::mib-2.17.1.1.0 = Hex-STRING: 00 00 00 00 00 00
SNMPv2-SMI::mib-2.17.1.2.0 = INTEGER: 0
SNMPv2-SMI::mib-2.17.1.3.0 = INTEGER: 4
From this I guess there's no information on the router about Vlans or anything. Other thing is that when I use community string indexing it returns a timeout. My theory is that this version doesn't support indexing but I don't know.
how can I get the Port Number from a MAC address from this "switch" (it's a router working as a switch) using SNMP?
View 2 Replies
View Related
