I have a 3725 router and would like to upgrade the slot:0 compact flash to a higher capacity. My question is, I can just pick up a 4GB compact flash card from walmart, or do I have to have a card from Cisco?
View 2 Repliescant format compact flash, 512MB,at boot is says
Loading disk0:/asa841-51-k8.bin... Booting...
Platform ASA5510
Loading...IO memory blocks requested from bigphys 32bit: 13008 dosfsck 2.11, 12 Mar 2005, FAT32, LFN
here ---> Currently, only 1 or 2 FATs are supported, not 64.
dosfsck(/dev/hda1) returned 1
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
open /dev/hdb1:No such file or directory
dosfsck(/dev/hdb1) returned 1
mount: mounting /dev/hdb1 on /mnt/disk1 failed: No such file or directory
mount: mounting /dev/hdb1 on /mnt/disk1 failed: No such file or directory Processor memory 868220928, Reserved memory: 62914560
what does this mean?Currently, only 1 or 2 FATs are supported, not 64.
I need to upgrade the compact flash memory on a 2821 router from 64 to 128, upgrade the ios, and re-script the router. So I'm wondering what is the correct sequence? With the router powered on, do i eject the existing flash, and install the new one or do I power down the router? Once the memory has been increased, then i can upload the new ios?
View 1 Replies View RelatedI am attempting to install a 512 MB Cisco COmpact Flash for an ASA 5520. We have inserted the compact flash but when we do a DIR, it does not show. even as an unformatted device.
What do we need to do to make this a usable CF? Do I just need to reload the ASA or do I need to format the CF. It has been inserted into the slot in the back of the ASA 5520 and we have ensured that is had been seated properly.
Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies View RelatedIs there a way to load a spare compact flash with a running-config, ASA IOS, & ASDM software via card reader? I need to load another flash card with all of the settings necessary for normal operation. This "spare" card will replace the flash that is currently in use. The reason for the replacement is capacity and because of changes made to the running-config. The "in-use" card is 256MB, the "spare" one is 512MB. Also, the new card will have a few changes made to the running-config, so it will, in essence, be a reload.
I have a card reader for the compact flash cards. If there is a way to load up this new card using the card reader, without monkeying with the firewall, I would prefer that. Like I said in the previous paragraph, this new flash card will replace the other one, once it's ready.
Hardware: ASA 5510
CF: 256MB (wanting to upgrade to the new 512MB card)
ASA IOS: 8.4
6509-E compact flash Internal vs External
View 1 Replies View RelatedHow to force the Cisco 1811 Router to read a Transcend CF 128MB? [code]
View 2 Replies View RelatedI read that there are internal and external flash memory in 3725 router that can max up to 128mb. So adding the sizes of internal and external flash memory, will that total to 256mb?
And also is the internal flash of 3725 just the same with its external flash?
I just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies View RelatedTrying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
Is there reason why WS-C3560C-8PC-S and WS-C3560C-12PC-S is not supported in Cisco Network Assistent? According to the data sheets for these switches CNA should be supported. I saw another forum post stating that the Gigabit versions has been added to the supported list as of version 5.7."The Cisco Catalyst 3560-C and 2960-C Series compact switches offer both the traditional Cisco CLI for detailed configuration and Cisco Network Assistant software, a PC-based tool for quick configuration based on preset templates."
View 2 Replies View RelatedI have just brought a brand new laptop which has WiFi init i have taken it across the road from my home to my brothers to get connection it shows the networks and signals but after putting in mt phase word and password it keeps asking me for a security network key i don't any clue where this is or how to obtain this. I would have thought because i have WiFi ill get connected straight away specially with the signals coming thru strong.
View 1 Replies View RelatedI was rather surprised today to discover that the latest IOS available for the 2960-C switches is 12.2 (55). Other similar switches, like the 2960S range are using IOS 12.2 (58) or 15.0.1-SE2. This doesn't sound like the end of the world at first, but 12.2 (55) does not include VTP 3, which is a major problem if you are using the compact switch within a large modern deployment.
Am I correct about the version?Is there any way to deploy VTP 3 to this switch?Is Cisco planning to issue modern IOS releases for this switch?
I am facing this particular issue while providing Cisco unified Wireless solution to the customer. We are having CAPWAP 1252 APs controlled by WLC.
Scenario: 50 persons sitting in a hall with closely packed chairs using wireless simultaneously. Wireless access provided by patch antenna at a height of 11m from the user. As one AP can server 25 users, 2 APs are placed with antenna directions facing the compact users. Each users gets very good signal from these two APs.
Whether there will be serious interference and client association issues in this scenario? once one AP associates 25 clients, whether other 25 clients associate completely to other AP?
I am a traffic shaping newcomer and need some guidance as how to BEGIN to approach a problem with traffic. We have been rolling out Windows 7 at sites and the additional traffic it causes on installation is considerable as it has to request information from our central site to populate My Documents and Outlook mailboxes.This has caused some problems on sites as there traffic rates increase to the point that QoS is not sufficient to protect voice traffic and delays and one-way audio are being experienced.One question is this - is GTS a solution or is CBWFQ within GTS the solution or is something else preferable? The sites involved are data/voice with a variety of routers.Second question is this - if we have a remote site with a 3725 router as the WAN aggregator with one 4506/Sup IV and one Cat 3550-24-PWR the shaping should be best placed on the 3725, correct? Also, are there issues with shaping incoming/outgoing traffic as I seem to have read?FYI, the 3725 router has 12.4(8d) with IP VOICE/NO CRYPTO IOS version. The 4506 has 12.1(23)E4 with basic L3 feature set.
View 1 Replies View Relatedany 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 Replies View RelatedI'm trying to bring up two t1 and bundle them into a multilink on a 3845 on one end and a 3725 on the other end. On the 3845 I have installed two VWIC-2MFT-T1-DI and on the 3725 I have installed two VWIC-2MFT-T1 and a 1DSU/CSU-T1-V2.
For some reason I'm able to bring up the T1's on the DSU/CSU WIC. When I try to connect the T1 on the other WICs, on the 3845 I see SLIPs and Interface Resets however on the 3725 there is no errors however I still see UP DOWN.
CONFIG 3845
controller T1 2/0/0
framing esf
linecode b8zs
cablelength short 133
channel-group 0 timeslots 1-24 speed 64
[code]....
I am implementing traffic export on the WAN interface of my 3725 router. I use a dialer interface for PPPoE which is applied to the Fa0/0 interface. This dialer WAN interface has Zone Based Firewall, NAT Outside, ACLs applied to it, as well as IP Traffic Export for an IPS. In what order would each of these items process a packet? In other words, is the order something like ZBF, ACL, IP Traffic Export, then NAT? How would QoS fit into something like this as well? I am asking because I am wondering how much processing the packets receive before they are mirrored over to my IPS.
View 1 Replies View Related I have a Cisco 3725 router with IOS version "Cisco IOS Software, 3700 Software (C3725-ADVIPSERVICESK9-M), Version 12.4(12)". And this router is serving as a CE route for our MPLS connection to the service Provider. We do also have multiple VRFs ( around 10) and the WAN interface is DS3. So we created point-to-point subinterfaces and we put them in different vrfs. We have now transitioned to a new ISP and the ISP requested us to mark all of our outgoing traffics with DSCP AF31. So I have created the following policy-map
policy-map TRAFFIC-OUT-WAN-AF31
class TRAFFIC-OUT-WAN
set ip dscp af31
class-map match-any TRAFFIC-OUT-WAN
match any
Now we do have multiple GRE tunnel interfaces sourced from one of the WAN subinterface ( which is a member of VRF A). So the moment I applied the the policy-map on this WAN sub-interface (using the syntax "service-policy out TRAFFIC-OUT-WAN-AF31"), most of the GRE tunnels went down. And there is eBGP running on top of these GRE tunnels.
I work for an ISP and we are currently bonding 5x 6Mb ADSL connections for use as a wireless backhaul. We are currently using a Cisco 3725 and bonding the links via MLPPP. This set up is working fine except that we are not getting the full 30Mb on the download side. We are seeing more like 18 to 20. I am wondering if we can acheive the full speed with our current set up or will we need something different to get the job done.
View 1 Replies View RelatedI'm trying to migrate the running-config from our old 3725 router to our new 3945e router. Almost all of the config is copied over except for a few lines that come up as unrecongnized commands. So it looks like these commands were either removed or changed to something new.
View 12 Replies View RelatedI have been using a route map to pick WAN exit points (PBR) on a 3725 router. This have been working fine with /24 networks. I am trying to pick the first /28 piece out of the 10.1.1.0 network and send it out a different exit from the rest of that network. I have tried the /28 entry at the start and end of the route map, although I thought the first match would stop any further route map processing. The entry does not seem to have any effect, as traffic from all addresses in the 10.1.1.0 /24 network exit per the "route-map 10-LAN permit 11" section.
access-list 5 remark Ten Dot 1 low 63 IPs
access-list 5 remark SDM_ACL Category=2access-list 5 remark Ten Dot One Low 63 IPs access-list 5 permit 10.1.1.0 0.0.0.63 log
[ code]....
Cisco 3725
IOS: (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T9
Wireless Module NME
Brief current running config below:
interface FastEthernet0/0
description WAN LINK
bandwidth 8192
[Code].....
I have a 3725 routeur configured to receive the PPP/ATM/DSL connexion of our customer. I have found that the routeur has created 1035 virtual-access (1035 is his max) but I only have 85 customer on this router
View 1 Replies View RelatedI have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
I am setting up multiple vlan interfaces on a pair of HSRP Routers that will provide layer 3 routing for a network. I am seeing this command sporadically show up in the router config mac-address-table static 0000.0c07.acd2 vlan 210
I am not entering this command. So far, it has not shown up on the companion 3725 router. I have a 2nd vlan I have just created and the problem hasn't shown up for that vlan as yet.Using C3725-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3) on the routers.
I have a 3725 router that is reporting the following syslog message:
%FAN-3-FAN_FAILED: Fans had a rotation error reported.
When I do a show environment all, I am getting the following message:
Fan status: Warning- low fan rpm condition detected.
Both the the fans are functional and are rotating fine. How do I repair?
I seem to be having a problem with DNS name resolution after configuring my router (Cisco 3725 running IOS image: c3725-adventerprisek9-mz.124-25.bin) for handling DHCP requests.
Before I made the change, everything was working correctly; I could ping Google.com from a computer inside my LAN and would get response from one of Google's public IP's like normal.
I had a separate DHCP/DNS server running Windows Server 2008 handling the DHCP request and DNS queries.
When I made the change, I turned off the DHCP/DNS server and issued the following DHCP commands to my router:
Code...
I'm trying to configure a SPAN session on a Cisco 3725 router, but it won't let me complete the command. The router has two Fast Ethernet interfaces: 0/0 and 0/1. I'm trying to configure a SPAN session with Fa0/0 as the source interface and Fa0/1 as the destination interface. [code] But when I try to configure the session, it seems like it's giving me the option to configure the SPAN session, but in the end the router won't let me: [code] When I type "?", why would it give me the option of using the Fast Ethernet interface as source port, then when I try to execute the command, it doesn't like it?
View 7 Replies View RelatedI had the 2 circuits go down at the same time from our ISP and I had to power cycle the router and when it came back up I went from VA # 2 to now VA 3#....I know what is what but it is confusing for my counterpart and I can not remove the old entry for VA#1 and VA#2. [code]
View 3 Replies View RelatedI'm developing a project where I use the SNMP protocol to discover the network. By discovering the network I mean go through all the routers and switches and retrieve the IP routing table from routers and the forwarding table from switches. With the routers I have no problem. For the switches I need to know for each port the MAC addresses and the Vlans. Basically it's use SNMP to find a port number from a MAC address. To do that i followed this tutorial: [URL]
The problem is that I'm using a Cisco 3725 Router with IOS 12.4 (21) and a NM-16ESW module to work as a Switch and when I use the OID .1.3.6.1.2.1.17 corresponding to the BRIDGE-MIB as it follows:
snmpwalk -v2c -c myrouter 10.1.1.5 .1.3.6.1.2.1.17
it returns:
SNMPv2-SMI::mib-2.17.1.1.0 = Hex-STRING: 00 00 00 00 00 00
SNMPv2-SMI::mib-2.17.1.2.0 = INTEGER: 0
SNMPv2-SMI::mib-2.17.1.3.0 = INTEGER: 4
From this I guess there's no information on the router about Vlans or anything. Other thing is that when I use community string indexing it returns a timeout. My theory is that this version doesn't support indexing but I don't know.
how can I get the Port Number from a MAC address from this "switch" (it's a router working as a switch) using SNMP?
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View Related