I need to upgrade the compact flash memory on a 2821 router from 64 to 128, upgrade the ios, and re-script the router. So I'm wondering what is the correct sequence? With the router powered on, do i eject the existing flash, and install the new one or do I power down the router? Once the memory has been increased, then i can upload the new ios?
View 1 RepliesI have a 3725 router and would like to upgrade the slot:0 compact flash to a higher capacity. My question is, I can just pick up a 4GB compact flash card from walmart, or do I have to have a card from Cisco?
View 2 Replies View Relatedcant format compact flash, 512MB,at boot is says
Loading disk0:/asa841-51-k8.bin... Booting...
Platform ASA5510
Loading...IO memory blocks requested from bigphys 32bit: 13008 dosfsck 2.11, 12 Mar 2005, FAT32, LFN
here ---> Currently, only 1 or 2 FATs are supported, not 64.
dosfsck(/dev/hda1) returned 1
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
open /dev/hdb1:No such file or directory
dosfsck(/dev/hdb1) returned 1
mount: mounting /dev/hdb1 on /mnt/disk1 failed: No such file or directory
mount: mounting /dev/hdb1 on /mnt/disk1 failed: No such file or directory Processor memory 868220928, Reserved memory: 62914560
what does this mean?Currently, only 1 or 2 FATs are supported, not 64.
I am attempting to install a 512 MB Cisco COmpact Flash for an ASA 5520. We have inserted the compact flash but when we do a DIR, it does not show. even as an unformatted device.
What do we need to do to make this a usable CF? Do I just need to reload the ASA or do I need to format the CF. It has been inserted into the slot in the back of the ASA 5520 and we have ensured that is had been seated properly.
Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies View RelatedIs there a way to load a spare compact flash with a running-config, ASA IOS, & ASDM software via card reader? I need to load another flash card with all of the settings necessary for normal operation. This "spare" card will replace the flash that is currently in use. The reason for the replacement is capacity and because of changes made to the running-config. The "in-use" card is 256MB, the "spare" one is 512MB. Also, the new card will have a few changes made to the running-config, so it will, in essence, be a reload.
I have a card reader for the compact flash cards. If there is a way to load up this new card using the card reader, without monkeying with the firewall, I would prefer that. Like I said in the previous paragraph, this new flash card will replace the other one, once it's ready.
Hardware: ASA 5510
CF: 256MB (wanting to upgrade to the new 512MB card)
ASA IOS: 8.4
6509-E compact flash Internal vs External
View 1 Replies View RelatedHow to force the Cisco 1811 Router to read a Transcend CF 128MB? [code]
View 2 Replies View RelatedI just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies View RelatedI have a cisco 2821 Router , it was operating fine but for the past 2 days its having a weird problem.During operation suddenly the connection is lost and when checked through console there is no IOS image on the Router (all configuration is erased and the router boots up in rommon mode and there is no IOS on dir Flash:I installed ios on it through tftp but again after some random time the IOS is automatically erased from flash i checked the config register value and its fine at 0x2102.
View 5 Replies View RelatedI have a cisco 2821 router configured as a CME version 7.1. Now I want to upgrade the IOS to version 15 to get a CME version 8.6 but I faced a problem that the flash of the 2821 is 64MB and the IOS version 15 required flash 128MB. I tried to replace this flash with another 128MB installed on Cisco 2811 router but when I installed the 128MB flash on the 2821 CME the 2821 didn't boot from it.
View 5 Replies View RelatedWhere can I find information regarding the details and upgrade path for the 2821 Intergrated services router. We are looking to upgrade from 12.4 (c2800nmc-spservicesk9-mz.12.4xxx.bin) to 15.1. Is their a spefici location to look for in the download or IOS area for upgrade paths?
View 3 Replies View RelatedI need to upgrade compact flash memory card for a 3800 router. Basically i want to upgrade code on this router and the current flash size (64Mb) cannot hold new image. I wanted to check if i swap the old flash (64 Mb) with a new one 256 mb, i will loose vlan.dat file since it's stored in flash. Is there a way i can copy vlan.dat to new flash which has new code before i change the boot statements and reload the router?
View 1 Replies View RelatedCurrently I have C2801 with 256MB of memory and 64MB of flash. I want to upgrade it to 384MB / 128MB.Do I need to get MEM2801-256D or I can use any PC133 SDRAM (144PIN) for memory? 384 is maximum I can install? Do I need to get MEM1800-128CF or I can use any compant flash card? 128MB is maximum I can install? (I saw 256MB flash on for C2801)
View 10 Replies View RelatedI am needing to upgrade the Flash card on our current ASA from 64mb to a 1GB card to make way from upgrading from 8.0 to 8.4. When i copy all the contents from the 64MB card through a card reader i am not getting the startup-config file copied over. I checked to make sure that all hidden files are shown, but i am not seeing it. I backed up the startup-config from the old 64mb card to a tftp server before switching the cards out. Is their something that i am missing?
View 4 Replies View RelatedI am doining a flsh upgrade for 12000 router ... I am following this guidelines
[URL]
when i do show version | i image System image file is "disk0:c12k-os-mbi-3.6.0.CSCsy28524-1.0.0/mbiprp-rp.vm"
but at doc it says : System image file is "disk0:c12k-os-mbi-3.6.0/mbiprp-rp.vm" i think my image has something wrong. what do you say ? actually from step 1 to 16 was going smoothly , but step 17 doesnt go ... and i jump to Flash Disk Upgrade Abort Procedure section and i rollback to old flash disk and now it is working ....
Regarding to step 17, why standby PRP is not ready , it shows no valid partner ?
I need to upgrade the ASA 5520 from OS 8.2(5)26 to 8.2(5)33. the ASA only has 64M of flash. I have a 256M flash card. What are the steps to upgrade the flash? I am not sure how it will boot up because the new flash will be blank?
View 2 Replies View RelatedI've got three WG302s of which the certificates on all of them are up. I've begun the process of replacing the firmware on one of them with OpenWrt. I've been using this to get the job done: url...I've been able to edit it up to the point of using fconfig to edit the boot script. I understand that I just need to edit two lines and the firmware replacement will be complete. [code]I've looked up fconfig commands to see if I could figure out how to edit the script lines.
View 1 Replies View RelatedI hope that we can get this DIR-825 back from the dead. I did the first portion of the 2.05NA upgrade while wired into LAN1 on the unit, after the reboot the power light went Amber and the unit would no longer respond to pings. I have searched around for various reset methods but have not been able to find a guide or a definitive current D-Link tech manual on how to fix a bad flash. I have tried pinging/arping/web browsing its default IP and the IP I had it set to to no avail.
View 2 Replies View RelatedI am running 12.3(11) T8 on Cisco 2821 platform and trying to upgrade to 15.0. No luck. So I tried to upgrade it to 12.4 24T. But failed several times on different routers. Is there an intermediate version I should land before jumping to 12.4 24T?
View 3 Replies View RelatedI tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon. but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?
View 5 Replies View RelatedI have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies View RelatedCurrently my ASA5510 has a 64MB internal flash. Does the ASA require a higher capacity flash for an IOS upgrade from 7.2(x) to 8.2(x)? The Cisco Release Notes does not state any internal flash requirement, but just wanted to double check.
View 2 Replies View RelatedI recently upgraded the flash and the RAM on one of my ASA 5505 lab machines. The flash was upgraded from 128 to 512MB and the RAM was also upgraded from 256 to 512MB. I am using asa845-k8.bin. The firewall boots and runs file until you issue the reload command. The system shuts down but never reloads.
View 11 Replies View RelatedI need to upgrade the flash memory of the ASA 5520 from 256Mb to 512Mb. As far as I realized the built-in flash memory called system compact flash and there is also an empty slot which it is possible to install a user flash.
What is the difference between user and system compact flash? and for upgrade can I just insert the user compact flash or do I need to upgrade the system compact flash? Where can I find the part number for each type?
I want upgrade my switches 2960-24PC-L RAM: 128MB and Flash: 28MB, but in the web page of cisco I see that the requirement of hardware is RAM: 128MB and Flash: 32MB.
I download the IOS file and this file is only 11.2MB so my question is if I can upgrade the IOS because my flash is enough for upload the IOS file.
while upgrade NME-NAM module IOS on 2821, as a result of sudden disorder in power system nam helper image crashed and it seems
i have to fix this !
(as you may know without helper image you cant load IOS image of NAM so it doesn't work !!) on the other hand in Cisco documents it's mentioned besides upgrading NAM IOS we can upgrade helper image too. but i couldn't found in Cisco downloads the appropriate link to download either older version or latest version of , Nam helper image. (even with CCO Account)
in addition i have a brand new NAM Module that contains NAM Helper Image but I couldnt find a way to tranfer this image via ftp to ftp server
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
Is there reason why WS-C3560C-8PC-S and WS-C3560C-12PC-S is not supported in Cisco Network Assistent? According to the data sheets for these switches CNA should be supported. I saw another forum post stating that the Gigabit versions has been added to the supported list as of version 5.7."The Cisco Catalyst 3560-C and 2960-C Series compact switches offer both the traditional Cisco CLI for detailed configuration and Cisco Network Assistant software, a PC-based tool for quick configuration based on preset templates."
View 2 Replies View RelatedI have just brought a brand new laptop which has WiFi init i have taken it across the road from my home to my brothers to get connection it shows the networks and signals but after putting in mt phase word and password it keeps asking me for a security network key i don't any clue where this is or how to obtain this. I would have thought because i have WiFi ill get connected straight away specially with the signals coming thru strong.
View 1 Replies View RelatedI was rather surprised today to discover that the latest IOS available for the 2960-C switches is 12.2 (55). Other similar switches, like the 2960S range are using IOS 12.2 (58) or 15.0.1-SE2. This doesn't sound like the end of the world at first, but 12.2 (55) does not include VTP 3, which is a major problem if you are using the compact switch within a large modern deployment.
Am I correct about the version?Is there any way to deploy VTP 3 to this switch?Is Cisco planning to issue modern IOS releases for this switch?
I am facing this particular issue while providing Cisco unified Wireless solution to the customer. We are having CAPWAP 1252 APs controlled by WLC.
Scenario: 50 persons sitting in a hall with closely packed chairs using wireless simultaneously. Wireless access provided by patch antenna at a height of 11m from the user. As one AP can server 25 users, 2 APs are placed with antenna directions facing the compact users. Each users gets very good signal from these two APs.
Whether there will be serious interference and client association issues in this scenario? once one AP associates 25 clients, whether other 25 clients associate completely to other AP?
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View Related