Cisco Firewall :: ASA 5510 - Load A Compact Flash Via Card Reader
Sep 13, 2011
Is there a way to load a spare compact flash with a running-config, ASA IOS, & ASDM software via card reader? I need to load another flash card with all of the settings necessary for normal operation. This "spare" card will replace the flash that is currently in use. The reason for the replacement is capacity and because of changes made to the running-config. The "in-use" card is 256MB, the "spare" one is 512MB. Also, the new card will have a few changes made to the running-config, so it will, in essence, be a reload.
I have a card reader for the compact flash cards. If there is a way to load up this new card using the card reader, without monkeying with the firewall, I would prefer that. Like I said in the previous paragraph, this new flash card will replace the other one, once it's ready.
Hardware: ASA 5510
CF: 256MB (wanting to upgrade to the new 512MB card)
ASA IOS: 8.4
View 15 Replies
ADVERTISEMENT
Jun 10, 2012
Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies
View Related
Sep 4, 2012
I have a 3725 router and would like to upgrade the slot:0 compact flash to a higher capacity. My question is, I can just pick up a 4GB compact flash card from walmart, or do I have to have a card from Cisco?
View 2 Replies
View Related
Aug 4, 2011
cant format compact flash, 512MB,at boot is says
Loading disk0:/asa841-51-k8.bin... Booting...
Platform ASA5510
Loading...IO memory blocks requested from bigphys 32bit: 13008 dosfsck 2.11, 12 Mar 2005, FAT32, LFN
here ---> Currently, only 1 or 2 FATs are supported, not 64.
dosfsck(/dev/hda1) returned 1
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
open /dev/hdb1:No such file or directory
dosfsck(/dev/hdb1) returned 1
mount: mounting /dev/hdb1 on /mnt/disk1 failed: No such file or directory
mount: mounting /dev/hdb1 on /mnt/disk1 failed: No such file or directory Processor memory 868220928, Reserved memory: 62914560
what does this mean?Currently, only 1 or 2 FATs are supported, not 64.
View 1 Replies
View Related
Sep 25, 2012
I need to upgrade the compact flash memory on a 2821 router from 64 to 128, upgrade the ios, and re-script the router. So I'm wondering what is the correct sequence? With the router powered on, do i eject the existing flash, and install the new one or do I power down the router? Once the memory has been increased, then i can upload the new ios?
View 1 Replies
View Related
Jun 5, 2012
I am attempting to install a 512 MB Cisco COmpact Flash for an ASA 5520. We have inserted the compact flash but when we do a DIR, it does not show. even as an unformatted device.
What do we need to do to make this a usable CF? Do I just need to reload the ASA or do I need to format the CF. It has been inserted into the slot in the back of the ASA 5520 and we have ensured that is had been seated properly.
View 4 Replies
View Related
Oct 27, 2011
6509-E compact flash Internal vs External
View 1 Replies
View Related
Oct 4, 2011
How to force the Cisco 1811 Router to read a Transcend CF 128MB? [code]
View 2 Replies
View Related
Nov 15, 2011
I just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies
View Related
Feb 16, 2009
I recently discovered the SIM card slot under the battery in my Latitude D630.I placed the SIM card in the slot but nothing happened.
The broadcom utility indicates that there is no device detected.How do I activate this device?does it need a specific driver?
View 3 Replies
View Related
Jun 5, 2013
In order to do a flash upgrade on a 5510, is there any way to get the files from the existing flash onto the new flash before you replace existing flash? Is there an online procedure?
View 2 Replies
View Related
Feb 1, 2012
I deleted the flash from an ASA5510. I was able to tftp a version back into the device, but cannot seem to correctly have the box boot from this flash. I get the following error:
!WARNING: BOOT variable added, but not a valid image disk0: /asa831-k8.bin
*** Output from config line 41,"boot system disk0:/asa83..."
I have tried every save syntax i can think of to save this flash, but have yet to have it boot with an image ( I keep booting into ROMMON and have to tftp the image back in)
View 5 Replies
View Related
May 9, 2012
My client has had to replace their ASA 5510. Upon importing the image to the brand new ASA they are unable to write to the flash.
They have run fcsk disk0: to no avail. show file system show 0 and 0 for Flash size and Free space on disk0.
Is there anything that can be done, short of formating flash and trying to reinstall the image? I have asked them to reload the ASA but they are reluctant to do so as they don't want the site to lose connectivity.
View 6 Replies
View Related
Jun 22, 2011
I need to upgrade the compact flash of my ASA 5510 from 256MB to 512MB. A friend's recommendation was to buy a card reader, copy all of the data from the existing card and paste it to the new compact flash. I have a hard time believing that it's that straight forward.
Any safer, more foolproof way of migrating between flash cards?
View 8 Replies
View Related
Oct 29, 2012
I was handed a firewall ASA 5520 but without external flash, I want to confirm that the ASA at least boot from rommon mode boot must have the external flash connected? I connected to power and I connect it by the console port it did not show any boot.Additionally I can confirm it is possible that you can connect a flash of a previous ASA model, say a 5510?
View 4 Replies
View Related
Apr 26, 2013
Currently, we are monitoring a Cisco ASA which is running Software version 8.4(4).1. It is showing high cpu load (reaching 90%) at some hours, and our client (who is the owner) has asked us to troubleshoot this issue, since this is not a normal operating condition for the ASA.
We have checked over many forums and documents about "high cpu related to Dispatch Unit process", but we still don't know where to begin, and what steps we could recommend to our client. I have uploaded an archive, where I have extracted these outputs:
-show processes cpu-usage sorted non-zero
-show memory
-show service-policy global
-show interface
-show run threat
View 1 Replies
View Related
May 2, 2011
Have a new ASA 5510 connected to the laptop via console. I need to load the IOS and the configure from another ASA. I have tftp client on the laptop. Do I just need to set the inside IP to the same subnet as my laptop? Will I need a crossover cable?
View 1 Replies
View Related
Sep 23, 2012
I have configured a tplink dual wan router + cisco ASA5510.
NET 1---- TP LINK ---- ASA5510 ---- COMPUTERS
NET 2----
The message: this page can not be displayed this showing. Some web pages only load when I click F5.
View 1 Replies
View Related
Jun 28, 2011
We are now using a ASA 5510 firewall and we would like to configure a internet load balance traffic in our environment.For example, some IP addresses go through local gateway for internet routing but some address go through VPN tunnel gateway.
View 1 Replies
View Related
Oct 3, 2012
I have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies
View Related
Dec 8, 2011
Base ethernet MAC Address: 00:0a:b7:07:35:80Xmodem file system is available. The system has been interrupted prior to initializing theflash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init load_helper boot switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4ô
View 1 Replies
View Related
Dec 7, 2011
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies
View Related
May 2, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop : [code] I know that the solution would be to download a new valid image from tftp via the common prompt but what i don't undertand is why i cant access the rommon prompt.
View 5 Replies
View Related
Mar 24, 2011
1. Do all the 2800 series have a rocker power switch on the rear?
2. Do all 2800 automatically power on when power is connected if the rocker is in the on position?
3. Is it possible to physically damage the flash card in a 2800 router if it was powered off during a write operation?
The story is I have a client who claims that the flash card was damaged due to a power off.
View 2 Replies
View Related
Mar 15, 2012
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
View 1 Replies
View Related
May 9, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop :I know that the solution would be to download a new valid image from tftp via the rommon prompt but what i dont undertand is why i cant access the rommon prompt. It justs boots with the message above in a loop
View 0 Replies
View Related
Jun 6, 2011
have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
View 5 Replies
View Related
Mar 15, 2012
I'm working on a distribution config for some routers with a software IPS. The problem I'm running into is the final [confirm] during setup. Is there any way to disable confirm messages in IOS?
View 1 Replies
View Related
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
May 12, 2007
I have an Inspiron E1705 and my wireless card/adapter takes about 3 minutes to load each log in. I called Dell, and they couldn't find out what was wrong. We tried things from internet settings, to shutting off all the start ups in MS Config. I've had this problem for a very long time. Windows will start up, and it seems like there is a 3 minute wait period of my computer doing nothing, and then finally, the wireless loads in my System Tray.
View 14 Replies
View Related
Dec 26, 2011
I can't get my Nook reader to connect. It is not a password issue. I entered all the info and the NOOK recognizes the DIR-601 connection, but it won't stay connected. There is a lock symbol showing and states that the dlink is "remembered, secured with WPA/WPA2 PSK" but when I try to connect it makes the attempt and then disconnects immediately. I have spent a couple of hours in the support section of the dlink site and can't figure this out
View 1 Replies
View Related
Sep 13, 2011
Currently we have deployed site to site vpn between 2 asa 5510 model. one is corporate site and one is remote site. now we plan to use radware load balancer in which 2 isp will terminate. now if at a remote site wecreate only 1 ipsec tunnel and mention sigle isp peering. if one isp fails at corporate how remote site will be access by site to site vpn through 2 isp vpn. what thing we need to do over asa as well as load balancer at both end.
View 6 Replies
View Related
Jan 15, 2012
A customer wants to get the back-plane load of a cat4506-e chassis with a sup6-E supervisory card.A would like to check how many bus are used on the backplane and if the command "sh envi chassis" is the good and only command to be used ?I'm not sur that there is only one bus on the cat4506-E as with a sup7 card the backbone speed can change.
View 2 Replies
View Related
