I was handed a firewall ASA 5520 but without external flash, I want to confirm that the ASA at least boot from rommon mode boot must have the external flash connected? I connected to power and I connect it by the console port it did not show any boot.Additionally I can confirm it is possible that you can connect a flash of a previous ASA model, say a 5510?
View 4 RepliesOur company is in the process of replacing our old firewall with a Cisco ASA since our old firewall can handle only 170 concurrent users and we are expanding fast. Can I know what are the considerations when selecting from the different models of ASA currently we are debating if we should buy a 5510 or a 5520 also can I know if cisco ASA also have a limitations on concurrent users online in a lan like our old firewall. By the way we are a Call Center company(going 500 seats) so we are using VOIP(Asterisk using SIP and IAX).
View 1 Replies View RelatedIn order to do a flash upgrade on a 5510, is there any way to get the files from the existing flash onto the new flash before you replace existing flash? Is there an online procedure?
View 2 Replies View RelatedI deleted the flash from an ASA5510. I was able to tftp a version back into the device, but cannot seem to correctly have the box boot from this flash. I get the following error:
!WARNING: BOOT variable added, but not a valid image disk0: /asa831-k8.bin
*** Output from config line 41,"boot system disk0:/asa83..."
I have tried every save syntax i can think of to save this flash, but have yet to have it boot with an image ( I keep booting into ROMMON and have to tftp the image back in)
My client has had to replace their ASA 5510. Upon importing the image to the brand new ASA they are unable to write to the flash.
They have run fcsk disk0: to no avail. show file system show 0 and 0 for Flash size and Free space on disk0.
Is there anything that can be done, short of formating flash and trying to reinstall the image? I have asked them to reload the ASA but they are reluctant to do so as they don't want the site to lose connectivity.
I need to upgrade the compact flash of my ASA 5510 from 256MB to 512MB. A friend's recommendation was to buy a card reader, copy all of the data from the existing card and paste it to the new compact flash. I have a hard time believing that it's that straight forward.
Any safer, more foolproof way of migrating between flash cards?
Is there a way to load a spare compact flash with a running-config, ASA IOS, & ASDM software via card reader? I need to load another flash card with all of the settings necessary for normal operation. This "spare" card will replace the flash that is currently in use. The reason for the replacement is capacity and because of changes made to the running-config. The "in-use" card is 256MB, the "spare" one is 512MB. Also, the new card will have a few changes made to the running-config, so it will, in essence, be a reload.
I have a card reader for the compact flash cards. If there is a way to load up this new card using the card reader, without monkeying with the firewall, I would prefer that. Like I said in the previous paragraph, this new flash card will replace the other one, once it's ready.
Hardware: ASA 5510
CF: 256MB (wanting to upgrade to the new 512MB card)
ASA IOS: 8.4
I am having trouble connecting router to my pc hp pavillion with windows vista using verizon internet.
View 1 Replies View RelatedI was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
View 2 Replies View RelatedI am using two firewalls to connect two different offices. Firewall 5510 is running ASDM 6.3 and 5505 is running ASDM 6.2, Problem is that even after connecting two sites, i am unable to ping remote network from either side. I am mentioned static route as tunneled.
View 1 Replies View RelatedMy router is a Dlink Model DI-624
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
official or unofficial (official more preferable) guide about upgrading IOS from 8.2 to 8.4 on ASA 5520 model?
View 1 Replies View RelatedTrying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
My customer is looking for cisco firewall which is equivalent to Fortigate 310B.
View 2 Replies View RelatedMy customer had a spare ASA5510 bought a few years before with 5 x FE and security plus license with HA. Now they would like to buy a new ASA5510 to configure HA with the spare one, but now the ASA5510 comes with 2GE+3FE. Can the two FW work in HA?
View 4 Replies View RelatedNeed this file to erase my flash memory?
View 2 Replies View RelatedWe have a customer that has a ASA 5525-x reporting only 4g flash memory rather than 8g has any 4g version of the 5525 or is the IOS reporting incorrectly the size, as it seems to be embedded on these units as a USB disk internal.
View 4 Replies View RelatedI am in the process of setting up the ASA5520 with the latest 8.4 firmware latest Anyconnect 3.0.
Unfortunately, the internal memory is sufficient enough for the ASA ASDM only. It says not enough memory when I tried to tftp the Anyconnect pkg.There is a external flash slot at the back of the ASA, I've inserted a 256mb CF card but when I do a show disk1: it shows
I just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin
Source file name []? asa804-k8.bin
Address or name of remote host [192.168.10.2]?
Destination file name [asa804-k8.bin]?
Writing file tftp://192.168.10.2/asa804-k8.bin...
!%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect)
Cisco asa#
I am needing to upgrade the Flash card on our current ASA from 64mb to a 1GB card to make way from upgrading from 8.0 to 8.4. When i copy all the contents from the 64MB card through a card reader i am not getting the startup-config file copied over. I checked to make sure that all hidden files are shown, but i am not seeing it. I backed up the startup-config from the old 64mb card to a tftp server before switching the cards out. Is their something that i am missing?
View 4 Replies View RelatedCan I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedHow do you save the command output from the CLI to a file on flash?
With IOS, I would normally use a pipe command to redirect to tftp, but the ASA doesn't support this as far as I can tell. As a work around I was thinking I could save the output to flash and then tftp that file off the ASA.
I need to upgrade the ASA 5520 from OS 8.2(5)26 to 8.2(5)33. the ASA only has 64M of flash. I have a 256M flash card. What are the steps to upgrade the flash? I am not sure how it will boot up because the new flash will be blank?
View 2 Replies View RelatedI was trying to erase some bad test configs on my 5505 with a write erase, but all VLAN and Ethernet configs remained. I hastily decided to do an erase flash. No I'm stuck at a ROMMON prompt with no image found to boot I'm hoping I don't have to TFTP a factory image. How do I find the images on disk0 and copy them?
View 16 Replies View RelatedI have two pix525 firewalls cann't boot up normaly and i find [[URL] no longer provides the falsh erase tool ,erasedisk.bin,download.
View 4 Replies View RelatedCurrently my ASA5510 has a 64MB internal flash. Does the ASA require a higher capacity flash for an IOS upgrade from 7.2(x) to 8.2(x)? The Cisco Release Notes does not state any internal flash requirement, but just wanted to double check.
View 2 Replies View RelatedI have pix 535 and wanted to erase the flash files (faulty) which already utilised 13 mb .so i cant upload new ios so i want erasedisk.bin ,i also have CCO account.
View 6 Replies View RelatedI recently upgraded the flash and the RAM on one of my ASA 5505 lab machines. The flash was upgraded from 128 to 512MB and the RAM was also upgraded from 256 to 512MB. I am using asa845-k8.bin. The firewall boots and runs file until you issue the reload command. The system shuts down but never reloads.
View 11 Replies View RelatedI have an ASA 5520, currently running version 7.25-k8. I'm preparing for an upgrade to version 7.25(4), so I transferred the software code (obtained via Cisco download) to the firewall vis SCP. I then issued the "verify flash:asa725-k8.bin" and it fails. It comes back with the error that the CRC did not verify, Data Integrity has been compromised". My first thought was the image did not copy correctly, so I deleted it and transferred it again. I got the same error. Then I decided to run a verify against the actual current code that was running on the firewall, and it came back with the same error. I don't understand what the problem is. I don't tend to think it's an SSH key related problem, as the method I use to access the firewall is via SSH and I have no problems. Worth noting,this firewall is part of an active/standby pair, and I observe the same behavior on the failover unit, it fails to verify.
View 3 Replies View RelatedIs it possible to use the USB ports on a ASA5510's to copy files onto the flash?
I have not been able to find any ionfo on this in the users guides ?
I need to upgrade the flash memory of the ASA 5520 from 256Mb to 512Mb. As far as I realized the built-in flash memory called system compact flash and there is also an empty slot which it is possible to install a user flash.
What is the difference between user and system compact flash? and for upgrade can I just insert the user compact flash or do I need to upgrade the system compact flash? Where can I find the part number for each type?
When I use ASDM or the CLI to copy (ftp) files from my management station to flash on my ASA5520. I get to 99% and then the gui or cli window hangs.
The ASA itself completely freezes i.e. no traffic in or out until I kill the transfer window and then it may reboot
[and yes, there is more than enough free space on the flash file system for the files]
ASA5520 V8.2(3) / ASDM V6.4(5)
I've had occasional issues with 5505 upgrades going south when the boot hangs on the image load due to a corrupt image. I need a way to validate the checksum of the new image after it is copied to flash. Remote upgrades become a real pain when you have to go onside just to delete an image, copy it into flash again, and boot.
View 1 Replies View Related