Cisco Firewall :: Use USB Ports On ASA 5510s To Copy Files Onto Flash?
Nov 9, 2011Is it possible to use the USB ports on a ASA5510's to copy files onto the flash?
I have not been able to find any ionfo on this in the users guides ?
ADVERTISEMENT
Cisco Switching/Routing :: 3925 ISR - Possible To Copy Files Between Flash
Jul 9, 2012I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies View RelatedCisco Firewall :: ASA 5550 - Cannot Copy IOS From Flash To PC
Jan 8, 2013I just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin
Source file name []? asa804-k8.bin
Address or name of remote host [192.168.10.2]?
Destination file name [asa804-k8.bin]?
Writing file tftp://192.168.10.2/asa804-k8.bin...
!%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect)
Cisco asa#
Cisco :: Copy Tftp Flash And Copy Flash Tftp Not Working?
Jul 19, 2011I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View RelatedCisco Switching/Routing :: 6509 Copy Sup Boot Flash To ATA Flash
Feb 26, 2012Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
Cisco Firewall :: Copy Files Between Failover ASA 5520?
Oct 29, 2012I made an ASDM upgrade for one of my two CISCO ASA 5520. If I copy a file to the primary ASA's flash, is there any command I can run on the primary ASA to copy a file to the secondary ASA?
View 1 Replies View RelatedCisco Firewall :: 5510 Get Files From Existing Flash Onto New
Jun 5, 2013In order to do a flash upgrade on a 5510, is there any way to get the files from the existing flash onto the new flash before you replace existing flash? Is there an online procedure?
View 2 Replies View RelatedCisco Firewall :: PIX 535 - Erase Flash Files From Monitor Mode?
Jun 1, 2010I have pix 535 and wanted to erase the flash files (faulty) which already utilised 13 mb .so i cant upload new ios so i want erasedisk.bin ,i also have CCO account.
View 6 Replies View RelatedCisco Firewall :: ASA 5520 - Copying Files To Flash Hangs / Reboots
Sep 8, 2011When I use ASDM or the CLI to copy (ftp) files from my management station to flash on my ASA5520. I get to 99% and then the gui or cli window hangs.
The ASA itself completely freezes i.e. no traffic in or out until I kill the transfer window and then it may reboot
[and yes, there is more than enough free space on the flash file system for the files]
ASA5520 V8.2(3) / ASDM V6.4(5)
Cisco WAN :: Copy Flash TFTP Error Rv042
Feb 24, 2012I have a really stupid problem with my RV042. The main logon password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.Am I missing something glaringly obvious? I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.
View 2 Replies View RelatedCisco WAN :: 3550 Copy Flash TFTP Error
Feb 20, 2012I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error. [code]
View 3 Replies View RelatedCisco WAN :: C1812 Possible To Copy IOS Image From Flash Of One Router And Use It To Upgrade Another
Jun 19, 2012I have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies View RelatedCisco WAN :: Unable To Take Backup Of Switch C2960 Using Copy Flash - Tftp
Jul 27, 2011I m unable to take backup of Switch c2960 using
#Copy flash: tftp
while i m taking it show some error
t#copy flash: tftp:
Source filename []? c2960-lanbasek9-mz.122-44.SE6
Address or name of remote host []? 10.23.120.15
Destination file name [c2960-lanbasek9-mz.122-44.SE6]?
%Error reading flash:c2960-lanbasek9-mz.122-44.SE6(Is a directory)
sh flash:
Directory of flash:/
2 -rwx 1919 Mar 1 1993 10:27:17 +05:30 private-config.text
3 -rwx 11056 Mar 1 1993 10:27:17 +05:30 config.text
4 -rwx 804 Mar 1 1993 05:30:42 +05:30 vlan.dat
6 -rwx 2072 Mar 1 1993 10:27:17 +05:30 multiple-fs
7 drwx 192 Mar 1 1993 05:37:02 +05:30 c2960-lanbasek9-mz.122-44.
SE6
Cisco Switching/Routing :: 3550 / Copy Flash TFTP Error
Feb 20, 2012I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
Cisco Switching/Routing :: 3500xl Switch Will Not Load Flash Or Copy From Xmodem?
Dec 7, 2011I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies View RelatedCisco WAN :: Copy IOS To One Flash In Router 2801 / Receive Message Of Insufficient Memory
Feb 6, 2011When I try to copy ios to one flash in router 2801, I receive the message of of insufficient memory, and have the follow out in the next command: [code] This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
View 6 Replies View RelatedHow To Map Network And Copy Files To D
Mar 22, 2012I am trying to map network and copy files to D:BackupSql_Backup?How can I sue this with spaces in my folders
net use R: \000.00.0.00Program FilesMicrosoft SQL ServerMSSQLBACKUP"
cd
echo off
R:
cd
Xcopy . /D /I /F /E /Y D:BackupSql_Backup
net use R: /delete /y
exit
Can Only Copy Files One Way On Network
Oct 12, 2011I have a network using windows home server 1, with 3 computers hooked up to it. Two of them work fine but the 3rd computer cannot successfully copy a file to the network. However, I can copy a file from the network to computer 3.This started suddenly about a week ago and there were no driver updates or anything changed that would cause this. When I copy a file from the network to computer 3 I get about 80mb/second. When I try the reverse, it pauses and after about 5 seconds I get a message saying:There is a problem accessing \serverserverfolder. Make sure you are connected to the network and try again.If I try to copy a small file of a few megabytes it will copy though.
View 5 Replies View RelatedSharing :: Copy Files Between PCs?
Jun 27, 2011I need to do a backup on our laptop prior to beginning the malware removal process. I need to move 22GB+. There is plenty of room on our desktop to store the files.Would it be best to use file sharing between the 2 PCs? They are both USB connected to the same router. Or, is it possible to transfer the files by connecting them directly to each other via USB?
View 5 Replies View RelatedCisco Switching/Routing :: Copy Flash Tftp Command Failed On 3750 Switch
Oct 5, 2010I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
Cisco Switching/Routing :: TFTPd32 - Copy Flash TFTP Error (timed Out) - Solarwinds
Feb 22, 2012I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
Linksys Wireless Router :: E1000 - Save / Copy Configuration Entries Onto Flash USB Drive?
Jul 7, 2011How do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies View RelatedNetwork App Very Slow Unless Copy Files At The Same Time
Oct 5, 2011Basic info: SBS 2008 (64bit), XP-sp3 (32bit) workstations, gigabit switch, SEP. App is Sage Masterbuilder.Network config: Server is 1gb to switch over CAT6. All the workstations are 100mb over CAT5. SEP is set to exclude all pertinent files on both the server and workstations.Problem: The program is called MasterBuilder and does job costing and much more. In the job costing feature there is an option to "Compute" job costing. In version 16.x, when the "Compute" was performed the task was done very quickly. After an upgrade to version 17.x it is very SLOW. According to tech support, our network is at fault since it is a database function over the network.Troubleshooting done: Tech support blamed our network speed (100mb) and switch. We had a Netgear 100mb switch so we replaced it with a GB switch however the cabling will not support GB. Being a managed switch I set all the ports to 100mb except the server port. Even tried the server plugged into a 100mb port and no change. I am confident there are no speed issues on our network. All other programs perform flawlessly. ACAD, Exchange, data transfers and many other high data use programs work perfectly. I updated the network card drivers in the server as well. There are no performance or resource issues on the workstations. I monitored the network traffic at the workstations, server and switch with no issues and about 2.5% utilization during the slow "Compute" process. The switch shows no errors at all, no collisions, no dropped packets, nothing. I also disabled the SEP.
During testing and while the slow "Compute" was going on, I copied a large folder (400mb) from the server to the workstations see the impact on network utilization. As soon as I start the copy process the "Compute" process speeds up to normal and zips by as it should. As soon as I cancel the copy process the "Compute" drops right back to very slow.
D-Link DCS-942L :: How To Copy Video Files From SD To PC
May 14, 2013I record videos after motion detection on the cameras sd-card. Is there a way to copy all the files from sd-card to the pc? I wasn't able to copy them with the web-interface. I don't just want to delete the videos from time to time. I also want to archive them local.
View 3 Replies View RelatedCisco Firewall :: Pinging Across 2 ASA 5510s
Dec 16, 2012Here's my basic setup:
Computer A:
IP- 192.168.0.3
Mask- 255.255.252.0
Gateway- 192.168.0.2
[Code]....
Computer A can ping Firewall 1 and Firewall 2, but not Computer B. Computer B can ping Firewall 1 and Firewall 2, but not Computer A. Firewall 1 can ping Firewall 2, Computer A, and Computer B. Firewall 2 can ping Firewall 1, Computer A, and Computer B.
Why can't the computers ping each other, but their default gateways can? I've specifically allowed ICMP any any on all the affected interfaces.
Cisco Firewall :: Setting Up Failover Mode On To ASA 5510s
Feb 9, 2012I've been given the task of adding a second ASA 5510 to a live ASA and making sure that the active/standby failover works, do I need a crossover cable?
View 4 Replies View RelatedCisco Firewall :: ASA5540s And 5510s - High Utilization Reported From ASA (8.4.1) To CSM (4.1)
May 30, 2011We have several ASA5540s and 5510s (v8.4.1) being managed by CSM (4.1) Every so often several of the ASAs will send SNMP messages to CSM stating very high CPU utilization reached, usually between 150% and 400% - sometimes as high as 4million %.Obviously you can't get greater than 100%.
View 1 Replies View RelatedCisco Firewall :: Connecting ASA 5510s To A DSL Modem With Static IP Range
Feb 27, 2013I have DSL service with AT&T and I have a Motorola 3360 modem. We also have a /28 network of static IPs from AT&T. When I login using PPPoE on the modem it gets x.x.x.190 as it's address. Our range is 177-190. I have two ASA 5510s in an active/passive failover configuration with the Ethernet port of the modem and one interface of each of the ASAs on a dumb layer 2 switch.
I want to setup this DSL connection as a backup to our main Internet connection. I cannot figure out what setting on the DSL modem to use to make this happen. I know I cannot use PPPoE in a failover setting so I can't have the modem in bridged mode. There is some mode where it passes the 190 address to the connected device and when I plug in a PC directly to the modem and set it for DHCP it does get 190 as it's address. So do I configure the ASA interface as 190 with one of the other addresses as it's standby? What do I set my route on the ASA to for use of this connection? Can I then make use of these other static addresses when plugging other devices into the layer 2 switch?
Cisco Switching/Routing :: 2960 Files Copy Crossing Office LAN Is Super Slow
Apr 16, 2012Two computers (XP and Win7) connected on office LAN, cisco 2960, not same switches, but all in the same rack, and link togeter, same IP subnet, tried to copy some kind of 26G files from one to another, using Windows share folders, and it showed need 23 hours to finish the copying.It's not the first time, actually we always experienced very slow speed when copying files on Windows share folders. Did not see any particualler message on the switch. ports are all full/100m.
View 9 Replies View RelatedLinksys Wireless Router :: Can't Copy Large Files To E4200 Media Server
Aug 27, 2011I've rolled back my E4200 router to the old firmware 1.0.0.1, then set up a media server.It generally works (e.g. it streams pre-existing media files to other devices). I can copy to this external drive small (say, < 1 MB) files. The drive has enough free space. However, I cannot copy to this external drive large (e.g. 700 MB) files.
View 5 Replies View RelatedCisco :: Avoid Deleting Files From Flash (Switch 2960) No Support EEM
Apr 3, 2012I am looking for ways to avoid deleting files from the flash in a Switch 2960, I found some scripts TCL / EEM but this switch does not support EEM (IOS c2960-lanbasek9-mz.122-58.SE2.bin).
View 13 Replies View RelatedCisco Firewall :: 5520 - Copy Configured ASA To New One?
Aug 7, 2011I have seen similar questions but with not a lot of answers for the ASA platform. As the title states, What procedures can I use to copy a pre-existing configured CISCO ASA 5520 to a brand new CISCO ASA 5520. I have found a URL that seems to answer some questions but not all. [URL]
The URL talks more about the PIX's than the ASA
Is there any documentation or shorter procedures for product specific on the 5520?
Cisco Firewall :: 5505 Copy Ftp Fails?
Mar 28, 2011The FTP server log shows no hits, from 192.168.1.4 I can telnet to 5505 no problem.
Doing everything on inside interface eth0/1, ftp server shows up and arp table of 5505 has correct mac for 192.168.1.4
ciscoasa# copy ftp://bob@192.168.1.4/asa841-k8.bin disk0:
Address or name of remote host [192.168.1.4]?
Source username [bob]?
[Code]...
