Cisco :: Avoid Deleting Files From Flash (Switch 2960) No Support EEM
Apr 3, 2012
I am looking for ways to avoid deleting files from the flash in a Switch 2960, I found some scripts TCL / EEM but this switch does not support EEM (IOS c2960-lanbasek9-mz.122-58.SE2.bin).
View 13 Replies
ADVERTISEMENT
Jan 23, 2013
In a switch catalyst 2960 the IOS is erasing in flash, for the transfer IOs respalding to flash no function the current command. how is the method.
View 6 Replies
View Related
Aug 16, 2012
I have a wrt610n that I've used for years with no problem. The usb drive I've had plugged into it has worked great for a really long time, but it's fairly small. I bought a WD 1TB hard drive, formatted it with the router set everything up. after about a day I tried to upload a file from work and got an error, and it wiped the harddrive clean. I reloaded thinking it was a fluke and everything worked fine for about a month. Uploading and downloading worked fine from where ever I was at, on the local network or over the internet. Then I tried to upload a small file, got the error and all of my files were gone again.
View 1 Replies
View Related
Jan 14, 2013
I've got the Cisco E4200 v1 firmware 1.0.04I hooked an usb 2.0 enclosure to it running a WD red "NASware" 1TB drive to it.The drive works just fine, brand new, silent, runs cool enough. I'm not saying it's a super-drive, just not complaining of anything.I started using it as a backup drive. File disappear randomly.Gigabytes of files deleted. No power outages nothing happened, the Router is 24-7 on connected to a UPS. So it is the drive, it was never shut off since connected the drive, about a month ago. It only shares connection among a couple desktop PCs a couple laptops a network printer and a couple smartphones, all updated, all clean that is no virus or anythingI removed the drive from the router and plugged it in the computer.Files were there,even though the files in the root were not all there, it must have crashed during the last modifications, although it's bad, and it's also bad that it does not give you a single sign it has crashed.
View 4 Replies
View Related
Oct 2, 2012
i sold off my e4200 & brought a e4500 .The e4200 has had a 2 TB W.D external drive attached ,i stream movies to a sat pvr in the .ts format .The problem is i set the e4500 up & it deleted my .ts files not once but 3 times.when i brought the e4500 i did roll the firmware back to the classic non cloud firmware.the third time i had turned the router off & once swtiched back on my files were gone .should i safely remove the drive from the set up ? what if i have a power failure?
View 5 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
Jun 5, 2013
In order to do a flash upgrade on a 5510, is there any way to get the files from the existing flash onto the new flash before you replace existing flash? Is there an online procedure?
View 2 Replies
View Related
Jun 1, 2010
I have pix 535 and wanted to erase the flash files (faulty) which already utilised 13 mb .so i cant upload new ios so i want erasedisk.bin ,i also have CCO account.
View 6 Replies
View Related
Nov 9, 2011
Is it possible to use the USB ports on a ASA5510's to copy files onto the flash?
I have not been able to find any ionfo on this in the users guides ?
View 2 Replies
View Related
Jul 9, 2012
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies
View Related
Sep 8, 2011
When I use ASDM or the CLI to copy (ftp) files from my management station to flash on my ASA5520. I get to 99% and then the gui or cli window hangs.
The ASA itself completely freezes i.e. no traffic in or out until I kill the transfer window and then it may reboot
[and yes, there is more than enough free space on the flash file system for the files]
ASA5520 V8.2(3) / ASDM V6.4(5)
View 1 Replies
View Related
Nov 28, 2012
I have copied the config and vlan.dat files via tftp to the computer and want to import them to a replacement switch. Both switches are 2960 model. I get the config over fine but not sure how to get the vlan.dat file to the flash.
View 1 Replies
View Related
Jun 27, 2012
I want upgrade my switches 2960-24PC-L RAM: 128MB and Flash: 28MB, but in the web page of cisco I see that the requirement of hardware is RAM: 128MB and Flash: 32MB.
I download the IOS file and this file is only 11.2MB so my question is if I can upgrade the IOS because my flash is enough for upload the IOS file.
View 12 Replies
View Related
Apr 16, 2012
Two computers (XP and Win7) connected on office LAN, cisco 2960, not same switches, but all in the same rack, and link togeter, same IP subnet, tried to copy some kind of 26G files from one to another, using Windows share folders, and it showed need 23 hours to finish the copying.It's not the first time, actually we always experienced very slow speed when copying files on Windows share folders. Did not see any particualler message on the switch. ports are all full/100m.
View 9 Replies
View Related
Dec 9, 2012
Cisco 2960 Optimization
The current software version is as follows:
System image file is "flash:c2960-lanbase-mz.122-35.SE5/
I WOULD LIKE TO KNOW THE UPGRADE PART TO BE ABLE TO ACCOMMPLISH THE FOLLOWING:
1. Deploy IOS Code containing Crypto ( K9 Image) features and reload the device with the new IOS
2. Generate RSA KEY on the network device + domain name.
3.set limit per MAC@to 4
4.set port to be protected instead of shutdown when limit exceeded
5.enable err disable recovery for link-flap events
6. set up required limits for port security settings preserving current NOD exception
7. i would like to know if i need to upgrade the IOS to achieve this. ?
View 1 Replies
View Related
Apr 25, 2013
I have this WS-C3750G-24T 16Mb flash switch and running on IOS Version 12.2(25)SEE4, RELEASEI would want to know a IOS version that supports IP SLA feature and which is compatable to the above model Switch.
View 3 Replies
View Related
Apr 18, 2013
what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
View 4 Replies
View Related
Jul 23, 2012
Can a C3560-24PS switch with 32 MB flash be loaded with IOS 15? Will it be able to execute the code and function properly?
View 2 Replies
View Related
Dec 8, 2011
Base ethernet MAC Address: 00:0a:b7:07:35:80Xmodem file system is available. The system has been interrupted prior to initializing theflash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init load_helper boot switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4ô
View 1 Replies
View Related
Jan 20, 2013
I have a 3560x switch with the flash formatted . I have tried to solve the problem by copying the IOS file to the flash. But the boot failed either .I have tried to copy the same IOS by the Xmodem, The boot failed again.My question is how to fixed the boot issues after the flash was formatted?
View 4 Replies
View Related
Jul 27, 2011
I m unable to take backup of Switch c2960 using
#Copy flash: tftp
while i m taking it show some error
t#copy flash: tftp:
Source filename []? c2960-lanbasek9-mz.122-44.SE6
Address or name of remote host []? 10.23.120.15
Destination file name [c2960-lanbasek9-mz.122-44.SE6]?
%Error reading flash:c2960-lanbasek9-mz.122-44.SE6(Is a directory)
sh flash:
Directory of flash:/
2 -rwx 1919 Mar 1 1993 10:27:17 +05:30 private-config.text
3 -rwx 11056 Mar 1 1993 10:27:17 +05:30 config.text
4 -rwx 804 Mar 1 1993 05:30:42 +05:30 vlan.dat
6 -rwx 2072 Mar 1 1993 10:27:17 +05:30 multiple-fs
7 drwx 192 Mar 1 1993 05:37:02 +05:30 c2960-lanbasek9-mz.122-44.
SE6
View 1 Replies
View Related
Dec 25, 2011
I need to know if Cisco Switch 2960 support Netflow. If it doesn't, how do I configure the switch to enable Netflow?
View 3 Replies
View Related
Sep 13, 2012
I have CISCO RPS 600 (PWR-AC-RPS) is it support Catalyst 2960 and 3560 ? and which type of cable require since i have cable 22-18 pin and on my switch require 22-14 pin.
View 2 Replies
View Related
Mar 2, 2013
I have cisco 2960 and Catlyst 4510 switches now we are planning to implement IPV6.
i have the fallowing IOS on my switches.
C2960-lanbasek9-mz.122-50.se5
Cat4500e-entservicesk9-mz.122-54.sg1.bin
The above ios will support for IPV6 or I have to purchase new IOS, which version will support.
View 1 Replies
View Related
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
Dec 7, 2011
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies
View Related
Jun 14, 2012
I have a customer with Cisco 7940 and 7960 IP phones that they do not plan to replace. They do want a new LAN and are looking at the Catalyst WS-C2960S-48FPD-L and WS-C2960S-24PD-L as access layer devices.
these switches support the Cisco pre-standard PoE required by the 7940 and 7960 IP phones.
View 5 Replies
View Related
May 21, 2012
We're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies
View Related
Oct 5, 2010
I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
View 25 Replies
View Related
Dec 18, 2011
Does 2960-24PC-L can support codec G711 and G729.
View 1 Replies
View Related
Jun 20, 2012
I have some 2960 switches with Lan Lite ios in my infrastructure.And I try to configure them to support "trust device cisco-phone" and "switchport priority extend cos 0" on ports with cisco phones.But LAN Lite image does not support "mls qos trust device cisco-phone".can I use any workaround to trust cos of cisco phone and to remark PC traffic with cos 0?
View 1 Replies
View Related
Dec 13, 2012
I have a D-Link Gigabit switch and I am trying to transfer files from my laptop (directly connected to switch) to my external hard drive (also connected to switch):The problem is that I get very slow speed for a transfer of a single file. It seems that the network utilization goes to 25%(normal) for just a few seconds and then it drops to 2-3%Please see attached image and propose what I should check.
View 6 Replies
View Related
Aug 10, 2012
i have 2 desktop and 1 laptop and i want to share files each other without using switch hub or router.
my server core2 dou and have built in lan card and 1 NIC
my client desktop pentium 4 and have built in lan card
my client desktop intel celeron and built in lan card
i crimped 2 crossover utp cable, check my color coding:
A Stripe white orange
Orange
Stripe green white
Blue
Stripe blue white
[code]....
View 1 Replies
View Related