I made an ASDM upgrade for one of my two CISCO ASA 5520. If I copy a file to the primary ASA's flash, is there any command I can run on the primary ASA to copy a file to the secondary ASA?
View 1 Replies
Is it possible to use the USB ports on a ASA5510's to copy files onto the flash?
I have not been able to find any ionfo on this in the users guides ?
I have seen similar questions but with not a lot of answers for the ASA platform. As the title states, What procedures can I use to copy a pre-existing configured CISCO ASA 5520 to a brand new CISCO ASA 5520. I have found a URL that seems to answer some questions but not all. [URL]
The URL talks more about the PIX's than the ASA
Is there any documentation or shorter procedures for product specific on the 5520?
I was trying to upgrade from 8.3.1 to 8.3.2. but I am unable to copy via tftp to the ASA flash or disk0:
ASA5520# copy tftp: flash:
Address or name of remote host []? 10.88.127.153
Source filename []? asa831-k8.bin
Destination filename [asa831-k8.bin]?
[code]....
Half way thru writing to the disk, it goes for a reboot. There is more than enought space on the disk0. I tried copying via a Compact Flash, but the ASA is not detecting the Compact Flash (which I thinks should be disk1). I tried copying a asdm file, even that also went for a reboot.I am stuck now, unable to upgrade
Currently we have one ISP1 and all traffic goes to this way. Suppose our isp1 goes down, our outside user cant get the server. All servers are nated to this ISP1.We planned to purchase a another ISP2. Shall we Configure same inside server to map this ISP2? so that one primary ISP1 goes down it will take place the outside trafficISP2.
View 1 Replies View RelatedIs it possible to setup 2 x Cisco ASA 5520 that are in an Active/Standby failover using sla monitoring?
For example ASA1 outside interface connects to an upstream switch and you setup sla monitor with icmp echo to ping that switch. The switch goes down and you need the other ASA2 to become the Active ASA. Can the sla monitor be automatically integrated with the failover commands for this to happen?
I am having ASA 5520 with active/standby configured. Around 2 days ago, the ASA stopped responding & all of my websites stopped working. when i checked the failover status it said that failover is off. I had to manually turn the failover to start my traffic flow.During this time my secondary ASA was not responding. After some time, the primary stopped responding & secondary became active......to solve this i had to make the secondary unit as failover unit primary & the primary unit as failover unit secondary. i did get a log on ASA :-
“(Primary) Disabling Failover” with error message no.105001 which states the below:-
Error Message %PIX|ASA-1-105001: (Primary) Disabling failover.
Explanation In version 7.x and later, this message may indicate the following: failover has been automatically disabled because of a mode mismatch (single or multiple), a license mismatch (encryption or context), or a hardware difference (one unit has an IPS SSM installed, and its peer has a CSC SSM installed).(Primary) can also be listed as (Secondary) for the secondary unit.
I have 2 ASA5520's in failover pair.After failing over I cannot run ADSM on the secondary (now active device), I get "unable to launch device manager from [primary address]"
I can ASDM to the primary device (now marked as "standby ready") on the failover address. I can SSH to it also.I CANNOT ASDM to the secondary device (now marked as "active") on the primary address. I CAN SSH to it.
When I run "sh asdm image" I get valid output (asdm image disk0:/asdm-645.bin) on both.However when I run "sh ver" on each it appears ASDM is not running on the secondary device :
Cisco Adaptive Security Appliance Software Version xxxx [only]
Compared with :
Cisco Adaptive Security Appliance Software Version xxxx
Device Manager Version 6.4(5)
It appears as though ASDM is only running on the primary device (regardless of the fact it is now in standby mode). Is this normal?
I am having to run in a failover condition due to a intermittent hardware fault on the primary unit but require access to the ASDM for monitoring/diag purposes during this condition.
Cisco still doesn't provide failover (active/standby) between two different types of ASA, right?
[URL]
"The two units in a failover configuration must have the same hardware configuration. They must be the same model, have the same number and types of interfaces, and the same amount of RAM"
i am trying to setup a failover pair on Cisco asa 5520 - need a state full failover. Do i need two ports dedicated to obtain the above - one for LAN based failover and one for state full fail over ? also do i need a switch in between to connect them ?
View 11 Replies View RelatedI have 2 Cisco 5520 ASAs and was configured for Fail over. Unfortunately our Primary ASA went down and Secondary becomes Active and network admin made lots of changes on Secondary Active ASA. What is the best practice to rejoin Primary as standby or active without loosing the existing configuration on Secondary Active ?
View 6 Replies View RelatedI have a running ASA5520 in my network and recently we plan to add a failover pair as a standby unit for the running asa. Both of the ASA have the same specs and software. the only thing that the soon to be secondary ASA does not have is the AnyConnect Essential license. is it still possible for the unit to be the standby unit?
below is the license capture from both of the unit.
Running ASA:
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
[Code].....
According to the link here:[URL]Starting with Version 8.3(1), it no longer needs to install identical licenses. Typically, we only buy a license only for the primary unit; for Active/Standby failover, the secondary unit inherits the primary license when it becomes active.So I wanna know if there's some additional configuration to synchronize the licenses such as SSL VPN or Context between the primary one and the second one? Or they can just synchronize by default as soon as I finish the failover configuration and when the primary one gets down, the second one will take over the role including licenses automatically?
View 4 Replies View RelatedWe have recently got 2 of our Cisco ASA 5520 firewalls through RMA. These are supposed to run in a Active/Active Failover Pair. There was only 1 RMA request that was opened for both the firewalls. We have received only 1 Activation key for this RMA request for both the firewalls. Just want to check with you if this Activation key will work on both firewalls or do we need a get a seperate one for the other box.
View 1 Replies View RelatedRecently, I unable to configure the failover on bridge group in transparent mode . I have five interfaces .out of this only 3 is showing in the show run config . Whether I can config failover on on of the data interfaces.
I have the ASA 5520 with the version ASA Version 7.2(4) <context>
I have a problem with my asa phone proxy. i have two ASA 5520 in HA. I have 10 phone register with ASA active primary. if i execute the command show phone-proxy secure-session. i can see the phone session on the ASA.
if i perform the same command on the passive ASA i can't see the session replicated from the active member.
If i switch the cluster the phone enter in a registrating loop and can't connect to the ASA now active.
If i switch back immediately (the session are still present on the first asa) the phone register again and all works
the ASA have version 8.4(5)
the phone are a 7921g
is normal that the skinny don't start again and re-register the phone on the ASA that became active after failover?
I have one ASA 5520 up and runnign, with complete configuration (ssl customization, DAP, CSD...) with bunch of files on flash drive, etc. I am using software 8.3Now I received one 5520 that I want to use failover, it is with 8.3, I will make sure that ASDM is also the same on both...
So, my question is how to make my running ASA to become primary and to push all info (config, files on flash, etc) to new ASA?
I found few examples, but nothing tells me how to force one ASA to be the source for sync.
What kind of cable is used for failover in asa 5520 ?
View 11 Replies View RelatedFrom ASA 5520 we tested the interface failover it not working even the interface are getting monitor .
primary is active.
Manually we shut the outside interface of the primary device configuration is getting reflecting in secondary as outside interface shut. Interface failover not happen.
ii All the interface are getting monitor when we gave command sh failover. even though when we shut outside interface failove not happening.
how to do the interface failover in ASA 8.4 version.
What process I need to follow to rebuild my failover unit? I've had to turn it off because it seems that both the primary and secondary were thinking they should both be the active unit. I'm not sure why. But in turning off the failover, I had internet access again. So I think I want to rebuild the secondary unit's configuration. Do I need to turn off failover from the primary unit first? Disconnect the secondary unit, console into it and remove the configuration (command to remove from flash?)? Rebuild the interfaces..all interfaces or just STATE between the units? Just trying to get a list of the process
View 1 Replies View RelatedI am trying to map network and copy files to D:BackupSql_Backup?How can I sue this with spaces in my folders
net use R: \000.00.0.00Program FilesMicrosoft SQL ServerMSSQLBACKUP"
cd
echo off
R:
cd
Xcopy . /D /I /F /E /Y D:BackupSql_Backup
net use R: /delete /y
exit
I have a network using windows home server 1, with 3 computers hooked up to it. Two of them work fine but the 3rd computer cannot successfully copy a file to the network. However, I can copy a file from the network to computer 3.This started suddenly about a week ago and there were no driver updates or anything changed that would cause this. When I copy a file from the network to computer 3 I get about 80mb/second. When I try the reverse, it pauses and after about 5 seconds I get a message saying:There is a problem accessing \serverserverfolder. Make sure you are connected to the network and try again.If I try to copy a small file of a few megabytes it will copy though.
View 5 Replies View RelatedI need to do a backup on our laptop prior to beginning the malware removal process. I need to move 22GB+. There is plenty of room on our desktop to store the files.Would it be best to use file sharing between the 2 PCs? They are both USB connected to the same router. Or, is it possible to transfer the files by connecting them directly to each other via USB?
View 5 Replies View RelatedI am using csc-ssm module in Cisco ASA 5520 firewall, with the csc version as 6.3.1172.0. I have a public Ftp server and when i ever i transfer the zipped files more than 50 MB or 70 MB or more than that, it fails. I used to upload by clicking the ftp site and copy past the file to the location. After a certain point of time, the download fails with the below error on the explorer.An error occured copying a file to the FTP server. Make sure tou have permission to put file on the server.Details: The operation timedout
Firewall log is below.
ABCFTP1|21|10.120.110.162|1257|Teardown TCP connection 48091783 for Internet:ABCFTP1/21 to XYZ:10.120.110.162/1257 duration 0:00:27 bytes 656 TCP FINs .
-- When i remove the service policy from the firewall, and try to transfer the files, it goes through without any problem. ena
-- Pls check the attached screenshot of the ftp settings in CSC-ssm. There is no problem with downloading files from the server.
So i setup a failover active / passive with 2 ASA5520's
Primary asa has 750 Anyconnect vpn licensing and the secondary asa has 2 Anyconnect licenses
I haven't setup the second asa with the new 750 licenses i purchased but when i do a show version it shows that the failover licensed features shows 750...
Does this mean i do not have to install the secondary anyconnect licenses on the standby ASA unit?
output of secondary asa
:
Licensed features for this platform:Maximum Physical Interfaces : Unlimited perpetualMaximum VLANs : 150 perpetualInside Hosts : Unlimited perpetualFailover : Active/Active
[Code]......
I was trying to assing statefull link as same as LAN failover link on ASA5520 with VPN Plus license. But i am getting the below error. Is there any restriction in the license itself.
View 1 Replies View Relatedwe have two ASA 5520, on the failover unit is showing LU allocate xlate failed. We read on [URL] that it could be a memory problem , but have cheked it and we have 85% of memory free on both nodes. We also can see all xlate on failover unit.
We have forced failover this evenig and we can´t stablish outbound connexions by outside interface, we think xlates or nat cant work properly.
I am getting ready to setup avtice/standby failover on our ASA 5520's and have run in to an issue.I currently only have one External IP address available. My Idea was to use a private/placeholder IP address for the standby external IP Address, will this cause any issues with the failover? I know I won't be able to access the secondary from the outside, but that is not an issue.
View 2 Replies View RelatedWe apply a new anyconnect mobile license to our primary asa 5520 and the failover feature went into an off state. WE have now applied a second purchased anyconnect mobile to our secondary asa but the failover is still inactive/off.
bcoh1fw50# sh failover state
State Last Failure Reason Date/Time
This host - Primary
Disabled Ifc Failure 14:43:21 EST Jan 30 2013
[Code].....
I am trying to setup an active/standby failover with 5520's running 8.4(2) and am having problems with it not dropping connections during the failover. I am using a portchannel from the switch to each ASA and using sub-interfaces off that. I'm using the command Failover mac address Port-Channel1 “mac-address on primary Port-Channel1” “mac-address on standby Port-Channel1”.The command goes through but doing a show interface port-channel1 doesn't show a change in the mac address on the secondary unit after a failover when it becomes active.
View 3 Replies View RelatedCurrently l have two ASA 5520's in a active/passive failover scenario. Currently the interfaces for the inside and outside are fixed at 100/FULL.I want to repatch them into GigE ports setup as Auto Negotiate.Is there anyway of keeping the connections through the firewall active in this type of scenrio or will l have downtime disconnecting and repatching? or could l possibly disable failover and reconfigure each ?
View 6 Replies View RelatedBasic info: SBS 2008 (64bit), XP-sp3 (32bit) workstations, gigabit switch, SEP. App is Sage Masterbuilder.Network config: Server is 1gb to switch over CAT6. All the workstations are 100mb over CAT5. SEP is set to exclude all pertinent files on both the server and workstations.Problem: The program is called MasterBuilder and does job costing and much more. In the job costing feature there is an option to "Compute" job costing. In version 16.x, when the "Compute" was performed the task was done very quickly. After an upgrade to version 17.x it is very SLOW. According to tech support, our network is at fault since it is a database function over the network.Troubleshooting done: Tech support blamed our network speed (100mb) and switch. We had a Netgear 100mb switch so we replaced it with a GB switch however the cabling will not support GB. Being a managed switch I set all the ports to 100mb except the server port. Even tried the server plugged into a 100mb port and no change. I am confident there are no speed issues on our network. All other programs perform flawlessly. ACAD, Exchange, data transfers and many other high data use programs work perfectly. I updated the network card drivers in the server as well. There are no performance or resource issues on the workstations. I monitored the network traffic at the workstations, server and switch with no issues and about 2.5% utilization during the slow "Compute" process. The switch shows no errors at all, no collisions, no dropped packets, nothing. I also disabled the SEP.
During testing and while the slow "Compute" was going on, I copied a large folder (400mb) from the server to the workstations see the impact on network utilization. As soon as I start the copy process the "Compute" process speeds up to normal and zips by as it should. As soon as I cancel the copy process the "Compute" drops right back to very slow.
I record videos after motion detection on the cameras sd-card. Is there a way to copy all the files from sd-card to the pc? I wasn't able to copy them with the web-interface. I don't just want to delete the videos from time to time. I also want to archive them local.
View 3 Replies View Related
