Cisco Firewall :: 5520 - ASA Failover Pair With Different License
Apr 15, 2013
I have a running ASA5520 in my network and recently we plan to add a failover pair as a standby unit for the running asa. Both of the ASA have the same specs and software. the only thing that the soon to be secondary ASA does not have is the AnyConnect Essential license. is it still possible for the unit to be the standby unit?
below is the license capture from both of the unit.
Running ASA:
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
[Code].....
View 3 Replies
ADVERTISEMENT
Mar 6, 2013
Our customer has purchased 2 x L-ASA-AC-E-5520= Anyconnect Essentials VPN Licenses (750 Users)Ive installed both activated licenses as per the cisco guides, I didnt get any errors on the install. I did a reload on both, they are both back up and running as active/standby but when I do a sh ver the license still shows "ASA 5520 VPN Plus License"Am I being dumb and has this worked successfully or should it not now display Anyconnect when I do a sh ver?
View 8 Replies
View Related
Oct 31, 2012
i am trying to setup a failover pair on Cisco asa 5520 - need a state full failover. Do i need two ports dedicated to obtain the above - one for LAN based failover and one for state full fail over ? also do i need a switch in between to connect them ?
View 11 Replies
View Related
Mar 20, 2012
We have recently got 2 of our Cisco ASA 5520 firewalls through RMA. These are supposed to run in a Active/Active Failover Pair. There was only 1 RMA request that was opened for both the firewalls. We have received only 1 Activation key for this RMA request for both the firewalls. Just want to check with you if this Activation key will work on both firewalls or do we need a get a seperate one for the other box.
View 1 Replies
View Related
Mar 3, 2011
I have one ASA 5520 up and runnign, with complete configuration (ssl customization, DAP, CSD...) with bunch of files on flash drive, etc. I am using software 8.3Now I received one 5520 that I want to use failover, it is with 8.3, I will make sure that ASDM is also the same on both...
So, my question is how to make my running ASA to become primary and to push all info (config, files on flash, etc) to new ASA?
I found few examples, but nothing tells me how to force one ASA to be the source for sync.
View 2 Replies
View Related
Jun 3, 2013
According to the link here:[URL]Starting with Version 8.3(1), it no longer needs to install identical licenses. Typically, we only buy a license only for the primary unit; for Active/Standby failover, the secondary unit inherits the primary license when it becomes active.So I wanna know if there's some additional configuration to synchronize the licenses such as SSL VPN or Context between the primary one and the second one? Or they can just synchronize by default as soon as I finish the failover configuration and when the primary one gets down, the second one will take over the role including licenses automatically?
View 4 Replies
View Related
Mar 24, 2013
We apply a new anyconnect mobile license to our primary asa 5520 and the failover feature went into an off state. WE have now applied a second purchased anyconnect mobile to our secondary asa but the failover is still inactive/off.
bcoh1fw50# sh failover state
State Last Failure Reason Date/Time
This host - Primary
Disabled Ifc Failure 14:43:21 EST Jan 30 2013
[Code].....
View 3 Replies
View Related
Nov 11, 2012
I have a pair of ASA5510 currently running as a failover pair. For some reason we need to move one of the firewall to another site, is there any best practice on splitting up the failover pair then I can re-configure the secondary unit offline?
I'm thinking to power down the secondary unit, unplug it from the network totally then erase the configuration on the secondary unit on console so I can re-configure it. For the primary unit, I will disable the faiolver config by "no failover" on the primary unit. Is that necessarily all thing for splitting up the failover cluster?
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB(code)
View 2 Replies
View Related
Dec 6, 2012
Preparing to upgrade the IOS on a failover pair of ASA 5580's and was wandering what is gonna happen after I've upgraded the IOS on the standby unit and rebooted. How is the active unit going to react when it sees an IOS mismatch prior to me making the standby the primary and upgrading it's IOS ?
View 2 Replies
View Related
Apr 13, 2011
I currently have two 5540's in an Active/Standby pair. The primary unit failed on February 12th, so the secondary ASA is now the active one. My question is this - we have made a lot of changes since February 12th and I am planning on fixing this failover issue over the weekend. Will the secondary (now active) FW sync it's config to the non-active FW, or will the failed FW sync it's out-of-date config - removing any changes that we've made in the last month or so.
View 1 Replies
View Related
Jun 11, 2009
we are running two failover pairs of asa (5510, 5505) in two different locations in active/standby configurations.Is it possible to access the inside ip of the standby unit via vpn terminated by the active unit? It's only for monitoring.With our configuration here it is not.Is that possible in general?
View 6 Replies
View Related
Jun 28, 2011
Since the "zero-downtime upgrade" is not supported, I would like to validate the process I put together for upgrading a failover pair of asa5550 with the characteristics below. Specifically I am concerned with the role of the standby during the upgrade. This is my setup:
.- single context mode
.- active/standby
.- current firmware asa821-k8.bin / asdm-621.bin
.- role: firewall and VPN concentrator for segmented server farm network. Dynamic/static/exemption NAT heavily used.
My target is asa842-k8.bin / asdm-645.bin and I am doing a two step upgrade (8.2(1) -> 8.3(1) -> 8.4(2)) to avoid the "unidirectional" attribute and CSCtf89372 bug issues. This is a short version of what I have in mind:
.- Verify stability of failover pair and make adequate backups before beginning.
.- plug into the console of active, ssh into active and standby.
.- vpn/act(config)# no failover ( disable failover from active )
[Code]....
After reboot, point to 8.4(2) and reload again. Same concern regarding the standby unit.
I understand there might be configuration tweaks needed to the NAT configuration. After second reboot test connectivity and if successful, on active "failover", "write standby" and "failover reload-standby". Otherwise "downgrade" and back to the drawing board.
View 6 Replies
View Related
Oct 16, 2012
What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies
View Related
Jun 19, 2012
I have ASA-SM failover pair in two Catalyst 6500 switches. I send from switch to ASA-SM management VLAN 1234 to admin context for management purposes. I have another 3 contexts on ASA-SM. Can I have same managemenet VLAN1234 on each ASA-SM context? Can it work?
View 1 Replies
View Related
Apr 12, 2011
I need to upgrade the active/standby failover pair of 5510 ASA's to have1 Gig DRAM each, and I am trying to plan out the upgrade process. I'm looking for a zero downtime upgrade process.
I know that the failover pair has to have the same amount of memory, so how do I perform a zero-downtime upgrade process?Can I power off the standby unit and upgrade it's memory first? Or will it cause a memory mismatch between the active and standby units when it is powered on?
View 2 Replies
View Related
Aug 8, 2011
A few weeks ago, I replaced a PIX 515E with a pair of ASA 5520's. We have a few basic web applications behind the ASA's. Nothing complex; just port 80/443 traffic. During the swap, we basically just copied the config from the PIX to the ASA. So the config is virtually identical.
Since the swap, we have one small set of users who gets timed out when trying to get to the application. This small set of users are scattered across the state of Alaska, and they are all accessing the Internet via a satellite connection. All other users across North America can access the application just fine.
Since the satellite connections are relatively slow, but they worked fine when going through the PIX, I suspect the issue is a difference in the default TTL (or similar parameter) between the PIX and the ASA.
View 5 Replies
View Related
Apr 19, 2011
I am looking for redundant asa deployment for fail over set up . however both units have csc cards. does this product ASA5510-CSC10-K9 has license for fail over ? what's the part no for asa failover license ?
View 2 Replies
View Related
May 22, 2011
According to Cisco, one of the ASAs must have an Unrestricted License [URL]:
"On the PIX/ASA Security appliance platform, at least one of the units must have an unrestricted (UR) license. The other unit can have a Failover Only Active-Active (FO_AA) license, or another UR license. Units with a Restricted license cannot be used for failover, and two units with FO_AA licenses cannot be used together as a failover pair."I am unfamiliar with the different ASA licenses, so with my current license, I am unable to enable failover on my two ASAs. Here is a snippet of the "show version" output on one of my ASAs (they are the same as far as licenses go):
Licensed features for this platform:Maximum Physical Interfaces : UnlimitedMaximum VLANs : 250Inside Hosts : UnlimitedFailover : Active/ActiveVPN-DES : EnabledVPN-3DES-AES : EnabledSecurity Contexts : 5GTP/GPRS : DisabledSSL VPN Peers : 10Total VPN Peers : 5000Shared License : DisabledAnyConnect for Mobile : DisabledAnyConnect for Cisco VPN Phone : DisabledAnyConnect Essentials : DisabledAdvanced Endpoint Assessment : DisabledUC Phone Proxy Sessions : 2Total UC Proxy Sessions : 2Botnet Traffic Filter : Disabled
This platform has an ASA 5550 VPN Premium license.
View 5 Replies
View Related
Mar 3, 2011
I Have ASA 5510. And I had two ISPs and I need to configure ISP failover. So which license i need? I Had License ASA-CSC10-PLUS License.
View 1 Replies
View Related
Nov 1, 2011
I used to have this situation where I need to replace faulty ASA5510 (this FW did not failover to standby FW) with the new one.
But the problem is the new ASA5510 came with Base License only not with Security Plus License which is needed to allow this brand new device to be configure failover.
how do I pull out Security Plus License from old FW and switch it to new FW (Base License) and activate to Security Plus License.
View 5 Replies
View Related
Jan 11, 2012
Can i buy a plus license for asa 5520??
View 2 Replies
View Related
Jun 20, 2011
Currently we have one ISP1 and all traffic goes to this way. Suppose our isp1 goes down, our outside user cant get the server. All servers are nated to this ISP1.We planned to purchase a another ISP2. Shall we Configure same inside server to map this ISP2? so that one primary ISP1 goes down it will take place the outside trafficISP2.
View 1 Replies
View Related
Jul 19, 2011
Is it possible to setup 2 x Cisco ASA 5520 that are in an Active/Standby failover using sla monitoring?
For example ASA1 outside interface connects to an upstream switch and you setup sla monitor with icmp echo to ping that switch. The switch goes down and you need the other ASA2 to become the Active ASA. Can the sla monitor be automatically integrated with the failover commands for this to happen?
View 5 Replies
View Related
Mar 7, 2011
Do I need the security plus license to do HA with two 5520's?I was told by our purchasing department that the 5520 was supposed to be able to do HA out of the box, but when I look I see only the VPN + license. Does that mean I can download the security plus license? Or do I even need it on the 5520.
View 2 Replies
View Related
Nov 27, 2011
I have got ASA 5520. I am planning to install Cisco ASA AIP SSM-20 and Cisco ASA Content Security and Control (CSC) Security Services Module on ASA 5520.. However I am also thinking of adding AIP only as I can do the function of content filtering with proxy server. Relating this issue I would like to ask -
1. What would be the benefit of adding CSC ?
2. Do I have to pay the license cost every year for both of these SSM? What would be the cost ?
3. Upto how many SSM can I add into ASA 55020 ?
View 6 Replies
View Related
Apr 17, 2011
I am having ASA 5520 with active/standby configured. Around 2 days ago, the ASA stopped responding & all of my websites stopped working. when i checked the failover status it said that failover is off. I had to manually turn the failover to start my traffic flow.During this time my secondary ASA was not responding. After some time, the primary stopped responding & secondary became active......to solve this i had to make the secondary unit as failover unit primary & the primary unit as failover unit secondary. i did get a log on ASA :-
“(Primary) Disabling Failover” with error message no.105001 which states the below:-
Error Message %PIX|ASA-1-105001: (Primary) Disabling failover.
Explanation In version 7.x and later, this message may indicate the following: failover has been automatically disabled because of a mode mismatch (single or multiple), a license mismatch (encryption or context), or a hardware difference (one unit has an IPS SSM installed, and its peer has a CSC SSM installed).(Primary) can also be listed as (Secondary) for the secondary unit.
View 1 Replies
View Related
Nov 24, 2011
I have 2 ASA5520's in failover pair.After failing over I cannot run ADSM on the secondary (now active device), I get "unable to launch device manager from [primary address]"
I can ASDM to the primary device (now marked as "standby ready") on the failover address. I can SSH to it also.I CANNOT ASDM to the secondary device (now marked as "active") on the primary address. I CAN SSH to it.
When I run "sh asdm image" I get valid output (asdm image disk0:/asdm-645.bin) on both.However when I run "sh ver" on each it appears ASDM is not running on the secondary device :
Cisco Adaptive Security Appliance Software Version xxxx [only]
Compared with :
Cisco Adaptive Security Appliance Software Version xxxx
Device Manager Version 6.4(5)
It appears as though ASDM is only running on the primary device (regardless of the fact it is now in standby mode). Is this normal?
I am having to run in a failover condition due to a intermittent hardware fault on the primary unit but require access to the ASDM for monitoring/diag purposes during this condition.
View 2 Replies
View Related
Sep 27, 2012
Cisco still doesn't provide failover (active/standby) between two different types of ASA, right?
[URL]
"The two units in a failover configuration must have the same hardware configuration. They must be the same model, have the same number and types of interfaces, and the same amount of RAM"
View 1 Replies
View Related
Jan 25, 2012
I have 2 Cisco 5520 ASAs and was configured for Fail over. Unfortunately our Primary ASA went down and Secondary becomes Active and network admin made lots of changes on Secondary Active ASA. What is the best practice to rejoin Primary as standby or active without loosing the existing configuration on Secondary Active ?
View 6 Replies
View Related
Sep 19, 2012
Recently, I unable to configure the failover on bridge group in transparent mode . I have five interfaces .out of this only 3 is showing in the show run config . Whether I can config failover on on of the data interfaces.
I have the ASA 5520 with the version ASA Version 7.2(4) <context>
View 3 Replies
View Related
Dec 3, 2012
I have a problem with my asa phone proxy. i have two ASA 5520 in HA. I have 10 phone register with ASA active primary. if i execute the command show phone-proxy secure-session. i can see the phone session on the ASA.
if i perform the same command on the passive ASA i can't see the session replicated from the active member.
If i switch the cluster the phone enter in a registrating loop and can't connect to the ASA now active.
If i switch back immediately (the session are still present on the first asa) the phone register again and all works
the ASA have version 8.4(5)
the phone are a 7921g
is normal that the skinny don't start again and re-register the phone on the ASA that became active after failover?
View 1 Replies
View Related
Oct 29, 2012
I made an ASDM upgrade for one of my two CISCO ASA 5520. If I copy a file to the primary ASA's flash, is there any command I can run on the primary ASA to copy a file to the secondary ASA?
View 1 Replies
View Related
Oct 2, 2011
What kind of cable is used for failover in asa 5520 ?
View 11 Replies
View Related
