Cisco Firewall :: ASA 5510 Switch Failover License From Old To New Device

Nov 1, 2011

I used to have this situation where I need to replace faulty ASA5510 (this FW did not failover to standby FW) with the new one.
 
But the problem is the new ASA5510 came with Base License only not with Security Plus License which is needed to allow this brand new device to be configure failover.
 
how do I pull out Security Plus License from old FW and switch it to new FW (Base License) and activate to Security Plus License.

View 5 Replies


ADVERTISEMENT

Cisco Firewall :: ASA 5510 - License For Failover

Apr 19, 2011

I am looking for redundant asa deployment for fail over set up . however both units have csc cards. does  this product  ASA5510-CSC10-K9 has license for fail over ? what's the part no for asa failover license ?

View 2 Replies View Related

Cisco Firewall :: 5510 - Which License Needed For ISP Failover

Mar 3, 2011

I Have ASA 5510. And I had two ISPs and I need to configure ISP failover. So which license i need? I Had License ASA-CSC10-PLUS License.

View 1 Replies View Related

Cisco Firewall :: 5520 - ASA Failover Pair With Different License

Apr 15, 2013

I have a running ASA5520 in my network and recently we plan to add a failover pair as a standby unit for the running asa. Both of the ASA have the same specs and software. the only thing that the soon to be secondary ASA does not have is the AnyConnect Essential license. is it still possible for the unit to be the standby unit?
 
below is the license capture from both of the unit.
 
Running ASA:
Licensed features for this platform:
Maximum Physical Interfaces  : Unlimited
Maximum VLANs                : 150     

[Code].....

View 3 Replies View Related

Cisco Firewall :: Failover License Sync Between Two ASA 5520?

Jun 3, 2013

According to the link here:[URL]Starting with Version 8.3(1), it no longer needs to install identical licenses. Typically, we only buy a license only for the primary unit; for Active/Standby failover, the secondary unit inherits the primary license when it becomes active.So I wanna know if there's some additional configuration to synchronize the licenses such as SSL VPN or Context between the primary one and the second one? Or they can just synchronize by default as soon as I finish the failover configuration and when the primary one gets down, the second one will take over the role including licenses automatically?

View 4 Replies View Related

Cisco Firewall :: ASA 5550 Failover License Requirements?

May 22, 2011

According to Cisco, one of the ASAs must have an Unrestricted License [URL]:
 
"On the PIX/ASA Security appliance platform, at least one of the units must have an unrestricted (UR) license.  The other unit can have a Failover Only Active-Active (FO_AA) license,  or another UR license. Units with a Restricted license cannot be used  for failover, and two units with FO_AA licenses cannot be used together  as a failover pair."I am unfamiliar with the different ASA licenses, so with my current license, I am unable to enable failover on my two ASAs. Here is a snippet of the "show version" output on one of my ASAs (they are the same as far as licenses go):

Licensed features for this platform:Maximum Physical Interfaces : UnlimitedMaximum VLANs : 250Inside Hosts : UnlimitedFailover : Active/ActiveVPN-DES : EnabledVPN-3DES-AES : EnabledSecurity Contexts : 5GTP/GPRS : DisabledSSL VPN Peers : 10Total VPN Peers : 5000Shared License : DisabledAnyConnect for Mobile : DisabledAnyConnect for Cisco VPN Phone : DisabledAnyConnect Essentials : DisabledAdvanced Endpoint Assessment : DisabledUC Phone Proxy Sessions : 2Total UC Proxy Sessions : 2Botnet Traffic Filter : Disabled
 
This platform has an ASA 5550 VPN Premium license.

View 5 Replies View Related

Cisco Firewall :: ASA 5520 - Failover In Off State After Applying New License

Mar 24, 2013

We apply a new anyconnect mobile license to our primary asa 5520 and the failover feature went into an off state. WE have now applied a second purchased anyconnect mobile to our secondary asa but the failover is still inactive/off.
 
bcoh1fw50# sh failover state 
State          Last Failure Reason      Date/Time
This host  -   Primary
Disabled       Ifc Failure              14:43:21 EST Jan 30 2013

[Code].....

View 3 Replies View Related

Cisco Firewall :: ASA5520 - AnyConnect License On Active / Standby Failover Pair?

Mar 6, 2013

Our customer has purchased 2 x L-ASA-AC-E-5520= Anyconnect Essentials VPN Licenses (750 Users)Ive installed both activated licenses as per the cisco guides, I didnt get any errors on the install. I did a reload on both, they are both back up and running as active/standby but when I do a sh ver the license still shows "ASA 5520 VPN Plus License"Am I being dumb and has this worked successfully or should it not now display Anyconnect when I do a sh ver?

View 8 Replies View Related

Cisco Switching/Routing :: ISP HSRP With ASA 5510 Failover And Switch Selection?

Feb 27, 2013

I have two Cisco ASA 5510s that I would like to configure in an active passive failover setup.  The ASAs  are at the top of our rack and handle all our routing.  We have been  only using one ASA unit with one line from our ISP connected to the WAN/outside interface of the ASA.  We recently had our ISP setup two lines into our rack using HSRP.  I do not know what equipment they are running upstream of our ASAs but it is HSRP so it should be a set of Cisco routers/switches.  Originally I thought I could just connect the 2nd new line to our 2nd ASAs WAN/outside port and setup failover using a crossover cable between the ASAs.  After doing this config I had problems accessing some of our IPs in the subnet that the HSRP is part of.  If I disconnected the 2nd ASAs  WAN/outside line everything was fine.  After talking with my ISP they  explained that I need to connect both of my lines into our L2 network  and then from there into the ASAs. Currently below the ASAs I have two Catalyst 3560-X switches.  They are connected together with an ISL trunk and ASA-1s inside network connects to switch-1 and ASA-2 to switch-2.  One idea was to connect each of the HSRP  lines to each of my current switches and then from the switches to the  ASA's WAN/outside interface.  Finally back down from the ASA's to the  switches via the inside interface that we have currently.  This kind of  seems messy and a poor choice.  The other idea is to get two switches that would sit above the ASAs and connect the HSRP lines to them with the switches connected together.  They would then connect to the ASAs.  I like this idea better but I don't like having to buy two more full switches for this.  These switches would only use a couple of ports and only handle just the HSRP ISP lines to the ASAs.  Putting in two more 3560-Xs  would be a big waste of money and space for this.  So I was thinking of  using two Cisco SG200-08, 8 port gigabit basic managed switches for  this. 

View 5 Replies View Related

Cisco Firewall :: ASA5510 Security Context License Transfer To Another Device

Apr 30, 2012

Is it possivble to have 10 security licenses, license to a Cisco 5510 and have them transfeered to a Cisco5520?    

View 1 Replies View Related

Cisco Firewall :: Is ASA 5510 Firewall Required Any Subscription Or License

Nov 15, 2012

I am quite new to firewall, in my company one asa 5510 firewall is there.I configured inside, outside, dns, dhcp and nating.I need to config bandwidth limit (1Mbps) for inside port and I restruct like facebook, youtube and pornsites..And I heard that some subscription is required, really is it required?

View 1 Replies View Related

Cisco Firewall :: ASA 5510 ISP Failover

May 31, 2011

Configured ASA 5510 ISP failover and working fine.My ASA as configured as DHCP server also. So its serves IP addressing details including mask,default-gateway, DNS server IPs.Here my issue is whenever my ISP failover occurs my ASA sends previous ISP DNS server IPs to my inside clients.
 
Here i like to configure my ASA to serve IP addresses dynamically.Or is there any global DNS IP addresses which will work for all ISPs?

View 1 Replies View Related

Cisco Firewall :: Upgrade License On ASA 5510?

Oct 12, 2011

I have a two ASA HA and I'd like to upgrade the license to ASA5500-SSL-250. I need to know if i have to purchase one license (ASA5500-SSL-250) for the Active unit and one license  (ASA5500-SSL-250) for the standby unit.

View 3 Replies View Related

Cisco Firewall :: 5510 CSC Base License

Jan 27, 2013

We have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.

View 1 Replies View Related

Cisco Firewall :: ASA 5510 And License With AIP-SSM Connection

Oct 29, 2012

I have this box. I have few questions about it.
 
1)     Will I be able to update firmware (from 8.2 to 8.3 or higher for example) without smarnet for ASA 5510? And what can not I do without smartnet?
2)     I have only AIP-SSM-10 module to this asa 5510. is there a smartnet for it, too? And when I buy only module is there build in a 1 year subscription for  IPS signatures?
3)     If I have Cisco ASA 5510 base license, will my IPS on AIP-SSM-10 work?
4)     Also I'm planning in a year buy one more 5510 with same module and put ther in failover. Will I really need Security Plus license for failover (Active/Standby)? For Active/Active I know that I need one, yes?

View 5 Replies View Related

Cisco Firewall :: ASA 5510 - CSC 10 License Renewing

Apr 2, 2011

I have a problem with ASA5510 CSC10 license renewing. Initially, we had CSC license  with 500 seats, and renewed it to 250 seats. After that every time it shows that license expires day before today.(for example if today is 4 April it show that license expires on 3 April).

Clicking on "Check Status Online" didn't work. What can correct this problem ?

View 1 Replies View Related

Cisco Firewall :: ASA 5510 Failover With IP SLA Monitor?

Nov 28, 2011

Can I run Cisco ASA failover with dual ISP run active/standby configuration and SLA monitor to monitor the primary ISP gateway and failover to the secondary gateway but not failover to the failover firewall unless an actual event occurred that required a ASA failover?

View 3 Replies View Related

Cisco Firewall :: Configuring Failover For ASA 5510

Oct 16, 2012

I have two ASA 5510's that I want to setup in a Active/Standby configuration. My only question is on how to connect the inside ports to my LAN. I have 5 Catalyst 3750's stacked together that connect to the ASA's. Should I run the inside interface on ASA1 to a port on switch 1. Then run the inside interface on ASA2 to a port on switch2? And make sure both those ports are in the same VLAN? But, then when failover occured, how to I automatically make it clear the arp cache so the traffic starts flowing out of the right port?                   

View 1 Replies View Related

Cisco Firewall :: ASA 5510 Failover Trunk

Nov 25, 2012

I have a customer with two ASA 5510s.  All four ports are used by the following interfaces: inside, outside, dmz, and failover.  This customer is looking at getting redundant internet connections, but we don't have any ports to the redundant connection.  What I'd like to know is it possible to configure sub interfaces on one of the currently occupied ports (I'm thinking inside) and use one for inside and one for failover.  This way I could have the other port free for the redundant internet connection.

View 1 Replies View Related

Cisco Firewall :: Failover Between ASA 5510 And 5520?

Sep 27, 2012

Cisco still doesn't provide failover (active/standby) between two different types of ASA, right?
 
[URL]
 
"The two units in a failover configuration must have the same hardware configuration. They must be the same model, have the same number and types of interfaces, and the same amount of RAM"

View 1 Replies View Related

Cisco Firewall :: ASA 5510 To Use Failover Possibilities

Jul 26, 2011

We are going to buy a new Firewall ASA5510 to use failover possibilities.I just need to be sure it will be possible to implement as I have the following output after a "show ver" command: Cisco Adaptive Security Appliance Software Version 8.3(1) [code]

As you can see the failover line is set as "Disabled perpetual".We are actually using base license as i have not been able to find any contact for CISCO to get official support or new license.

View 1 Replies View Related

Cisco Firewall :: 5510 ASA Failover Licensing?

Feb 28, 2011

I have a customer who has purchased a Cisco 5510 and after we received it and all the necessary VPN, 3DES etc. licensing for it, then informed us that they order 2 T1 lines so they can have Internet failover.
 
My question is: Does this require an additional specialized license from Cisco in order to enable and configure it?  And if so, what that part number is?

View 2 Replies View Related

Cisco Firewall :: How To Do Network Failover Between Two ASA 5510

Apr 16, 2011

How to design a network setup and achieve failover in the below scenario. 
 
                                                                                                    (Vendor router)
L3-Switch ---- ASA FW1 ---switch-- Router 1 ------ MPLS cloud1 ----- Router A ------------ L3 switch
                                                                                                     (Vendor router)
L3-Switch ---- ASA FW2 ---switch-- Router 2------ MPLS cloud2 ----- Router B------------ L3 switch
 
I am planning to achieve the failover either of the following ways -
 
1)  Configuring both ASA FW as active/standby method .

2) configuring ASA FW 1 tracking command pointing to the  ISP end ip address so the traffic would be moved to secondary firewall by putting a  AD as 1 on ASA FW ......pointing to the ISP ip address and other floating route ( with a higher AD value) to the secondary firewall interface.
 
3) To configure HSRP between the Routers.

View 2 Replies View Related

Cisco Firewall :: ASA 5510 - Configure HA Failover

Jun 8, 2013

I have 2 ASA5510-SSL50-K9, can I configure HA Failover ?

View 7 Replies View Related

Cisco Firewall :: ASA 5510 - Difference Between CSC-10-PLUS And Security Plus License

Mar 3, 2011

I have ASA 5510. Is there any difference between CSC-10-PLUS license and Security Plus License...

View 3 Replies View Related

Cisco Firewall :: ASA 5510 Active And Standby Failover

Apr 18, 2012

i read that you need only one L-ASA5510-SEC-PL for setting up a Active/Standby Failover. I installed the license on the 1st ASA and tried to setup the failover via the ASDM wizard. It always fails, because the 2nd device can't have a 'base' license.So does this mean, i really need another license?

View 5 Replies View Related

Cisco Firewall :: 5510 Failover Hardware Compatibility

May 25, 2012

I have two ASA 5510, The one which I just got shows the CPU speed to be 1599MHz While the previous device (which is also 5510) reads the CPU as 1600 MHz.According to Cisco, for Failover redundant configuration, both devices must have same hardware configuration. Technically, this slight difference should not be an issue but I need to confirm that thess devices will work fine with failover configuration.

View 1 Replies View Related

Cisco Firewall :: ASA 5510 - LAN Based Failover Not Working

Jun 23, 2011

I have ASA 5510 connected as shown in attached diagram.Ideally when ASA 1 is active and if I boot Switch-1, ASA-2 shood take over. But that is not happening.When I boot SW1 , ASA-2 shows "Failover LAN Interface: failover Ethernet0/0 (Failed - No Switchover)" and remains standby.Fail over works properly If ASA-1 boots.

View 7 Replies View Related

Cisco Firewall :: ASA 5510 Failover Subinterfaces Monitoring

Jan 30, 2013

i have a couple of ASA 5510 in Active/Failover configuration. Failover LAN is configured on management0/0 e the ASA are connected with a back-to-back direct cable.
 
ASA has an interface in access mode inside with standby ip address and show failover is compliant with expected result in show failover (Normal)
 
ASA-PRIMARY# sh failover Failover On Failover unit PrimaryFailover LAN Interface: LANfailover Management0/0 (up)Unit Poll frequency 1 seconds, holdtime 15 secondsInterface Poll frequency 5 seconds, holdtime 25 secondsInterface Policy

[Code]....

View 2 Replies View Related

Cisco Firewall :: Adding Failover To Active ASA 5510?

Oct 14, 2012

I am adding a failover asa to an a firewall that is already in production. They are both 5510's, they both have the same abount of ram, have the same code versions. Will there be any downtime while adding the secondary in?

View 2 Replies View Related

Cisco Firewall :: ASA 5510 No 3des Free License Installed

Sep 12, 2012

I have Asa 5510 with base license and no 3des free license installed on to it.Will it be required for both the licenses to be installed on it for site to site tunnels to establish.This firewall is not taking the below commands to give and the tunnel is not getting through.tunnel-group x.x.x.x type ipsec-l2ltunnel-group x.x.x.x ipsec-attributes.

View 3 Replies View Related

Cisco Firewall :: ASA 5510 - Part Number For CSC-SSM With Premium Plus License?

Jul 3, 2011

 I would like to order module card CSC-SSM with premium plus license but i don't know which part number with have : Plus license: Adds anti-spam, anti-phishing, URL blocking/filtering and content control
 
i saw part number  ASA5510-CSC10-K9 but it standard license and it dont'have adds anti-spam, anti-phishing, URL Blocking/frltering and content.
 
Note;i use ASA 5510.

View 1 Replies View Related

Cisco Firewall :: ASA 5510 With Security Plus License Lost Contexts

Jan 28, 2013

I have a ASA 5510 with Security Plus License and when I looked at the devices a few days ago I had 2 contexts, however after configuring the Mgm port as a regular port the contexts show 0, why?  I can not find any post on the internet where this issue has happen:  here is the output from show ver:

Cisco Adaptive Security Appliance Software Version 7.0(8)
Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"

[Code]......

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved