Cisco Firewall :: 5510 CSC Base License
Jan 27, 2013We have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.
View 1 RepliesWe have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.
View 1 RepliesI am working on ASA 5505 with Base License that uses 3 VLAN's.
-My VLAN 1 is for used for my home network.
-VLAN 2 is connected to the public Internet and my IP gets assigned by ISP dynamically.
-VLAN 3 is DMZ where I will have few VM's that would need access to and from the Internet.
I am looking to work with following:
1) 172.16.0.2 that sits on DMZ will need to access public Internet over port 80
2) Permit access from the Internet over port 3389 to 172.16.0.2
3) Permit any host on private VLAN (192.168.0.0 network) to access 172.16.0.2 over the port 3389
4) Permit second VM on the DMZ VLAN let say 172.16.0.3 to access public Internet on all ports. Access in to this host is not permitted.
5) For some reason DHCP hosts are NOT getting DNS (8.8.8.8) entry when IP hets assigned or renew. I have a statements below but it is not working.
Also, if ACL rules for VoIP are written correctly. The goal is to permit these ports (SIP related) to access VoIP router. [code]
I'm tring to setup a DMZ for a guest wireless off of a 5505. So this device has a base license. It has vlan1 and vlan 2 for inside and outside.Another vlan is configured to be a failover for the currently active wan connection. It is using the "no forward interface" command.Can I add another vlan as a DMZ if I use the "no forward interface" command? [code]
View 6 Replies View RelatedI have ASA 5505 with base licence. I configured NATing and VPN(site to site). All are working fine.My ASA is base license so i created 2 VLANS, one is inside and outside.Inside i am using 10.91.40.0/24 serie IP addresses.Below are the new requirements that i need to configre:
1. First 30 IP addresses only needs internet directly.( Servers and Management)
2. If remaining IPs likes to use web then traffic needs to forward one proxy server( where he gives user authentiation)
My ASA 5505 base license allows for three VLANs, the third one can only initiate traffic to one other VLAN (as specified by no forward interface vlan <number> on the third VLAN). This doesn't mean it can't "access" the other VLAN, it just can't initiate traffic to it. A lot of people get that wrong.Let's say you've got three VLANs, one is OUTSIDE, two is DMZ, and three is INSIDE. On the second VLAN would I enter the no forward interface as vlan 3, then set the name via the nameif command and everything will work just fine. The DMZ will not be able to initiate traffic to the INSIDE, but will to the outside, and assuming you have your ACLs and NAT set up properly, it will be able to respond to traffic from the INSIDE.
Would that be best practice or would I enter the "no forward" interface as in VLAN 1, thus is being able to respond to traffic from the outside as opposed to the inside.
I had a DMZ set up but since there was an intrusion into my network, I am building it again.
I have a couple of 5505's with base licenses. One of the two has a limited output when running the sho version command, as it has a restricted license. What license I would need to buy in order to bring it up to "normal" base license ?
View 1 Replies View RelatedWell, I tried using the cisco configuration for ASA 5505 for blocking P2P: url...but this configuration only is usefull with programs like Kazaa, so I try this configuration to block ARES but the problem is that ARES try to make downloads from different ports, ¿How do I block ARES if there are sereveral ports ?
View 1 Replies View Relatedwe have a cisco ASA5505 with base license and 3 interface configured. Internal 192.168.1.1/24 DMZ 172.16.0.1/24 Outside 20.20.20.20/24 The DMZ is configured to allow the traffic pass to the outside interface only (base license allow only traffic to one interface) in order to let clients on this network to browse internet. On the outside interface there's a nat configuration that let the port 443 to be natted to an in internal server. Is it possible to let the clients in DMZ to access to the internal server on port 443 from the outside interface?
View 3 Replies View RelatedI have a base 5505 and would like to get AnyConnect working. To do that, would I have to first purchase either an essentials or premium license and then purchase the AnyConnect Mobile license?
View 1 Replies View Relatedwe have a customer with a ASA 5510 with a CSC module in it. The device tells us the Base license has expired. The new license has been renewed - after - the grace period. The Trendmicro site tells us the Base license is valid until 21 october 2013 but the CSC refuses to acknowledge this. The module is able to fetch updates form the Internet so it does not look like a connection problem to me (it also has a plus license which is also valid till far into 2013 and that one works).Is it possible that the current license key is "dead" and the CSC expects a new license key because the grace period was expired?
View 1 Replies View Relatedconfigure the Firewall ASA 5510 in context based configuration in HA Mode with two different subnet....
IP Details are below.....:
interface Ethernet0/0
nameif outside
security-level 0
[Code].....
I am quite new to firewall, in my company one asa 5510 firewall is there.I configured inside, outside, dns, dhcp and nating.I need to config bandwidth limit (1Mbps) for inside port and I restruct like facebook, youtube and pornsites..And I heard that some subscription is required, really is it required?
View 1 Replies View RelatedWe are trying to migrate WCS base license to NCS 1.1 .We have procured the migration license .In the licensing guide , it is mentioned as "L-WCS-NCS1-M-K9 License first, before adding the licenses migrated from your WCS installation"
1)Whether we need to add this migration license in WCS before genrating XML file or
2)Before adding XML file in NCS we need to add this in NCS ..
I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
I have a two ASA HA and I'd like to upgrade the license to ASA5500-SSL-250. I need to know if i have to purchase one license (ASA5500-SSL-250) for the Active unit and one license (ASA5500-SSL-250) for the standby unit.
View 3 Replies View RelatedI have this box. I have few questions about it.
1) Will I be able to update firmware (from 8.2 to 8.3 or higher for example) without smarnet for ASA 5510? And what can not I do without smartnet?
2) I have only AIP-SSM-10 module to this asa 5510. is there a smartnet for it, too? And when I buy only module is there build in a 1 year subscription for IPS signatures?
3) If I have Cisco ASA 5510 base license, will my IPS on AIP-SSM-10 work?
4) Also I'm planning in a year buy one more 5510 with same module and put ther in failover. Will I really need Security Plus license for failover (Active/Standby)? For Active/Active I know that I need one, yes?
I have a problem with ASA5510 CSC10 license renewing. Initially, we had CSC license with 500 seats, and renewed it to 250 seats. After that every time it shows that license expires day before today.(for example if today is 4 April it show that license expires on 3 April).
Clicking on "Check Status Online" didn't work. What can correct this problem ?
I am looking for redundant asa deployment for fail over set up . however both units have csc cards. does this product ASA5510-CSC10-K9 has license for fail over ? what's the part no for asa failover license ?
View 2 Replies View RelatedI Have ASA 5510. And I had two ISPs and I need to configure ISP failover. So which license i need? I Had License ASA-CSC10-PLUS License.
View 1 Replies View RelatedI have ASA 5510. Is there any difference between CSC-10-PLUS license and Security Plus License...
View 3 Replies View RelatedHow to install IP base liecense and Unified communication liecense in 2921 router?
View 1 Replies View RelatedI have Asa 5510 with base license and no 3des free license installed on to it.Will it be required for both the licenses to be installed on it for site to site tunnels to establish.This firewall is not taking the below commands to give and the tunnel is not getting through.tunnel-group x.x.x.x type ipsec-l2ltunnel-group x.x.x.x ipsec-attributes.
View 3 Replies View RelatedI used to have this situation where I need to replace faulty ASA5510 (this FW did not failover to standby FW) with the new one.
But the problem is the new ASA5510 came with Base License only not with Security Plus License which is needed to allow this brand new device to be configure failover.
how do I pull out Security Plus License from old FW and switch it to new FW (Base License) and activate to Security Plus License.
I would like to order module card CSC-SSM with premium plus license but i don't know which part number with have : Plus license: Adds anti-spam, anti-phishing, URL blocking/filtering and content control
i saw part number ASA5510-CSC10-K9 but it standard license and it dont'have adds anti-spam, anti-phishing, URL Blocking/frltering and content.
Note;i use ASA 5510.
I have a ASA 5510 with Security Plus License and when I looked at the devices a few days ago I had 2 contexts, however after configuring the Mgm port as a regular port the contexts show 0, why? I can not find any post on the internet where this issue has happen: here is the output from show ver:
Cisco Adaptive Security Appliance Software Version 7.0(8)
Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"
[Code]......
I am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies View RelatedWould like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies View Relatedbasic step to blocking site on ASA 5505 version 8.2(1) base license using CLI
View 1 Replies View RelatedI am bringing up a 3750x and a 2911 to replace a 3745 router with switchport module. I was plannng on moving all the VLAN interfaces off the 3745 onto the 3750x and turning up EIGRP. I discoved the 3750 has the LAN Base license, so I can't run eigrp off of it. My question or worry now is, will the LAN base license prevent the switch from doing interface VLAN routing between the different VLAN's configured on it or will I have keep all the VLAN interfaces on the new router and just have a router on a stick setup?
View 4 Replies View RelatedIs it required for the 3des license upgrade for the asa5510 to reboot for the further configuration of site2site tunnels.
View 1 Replies View RelatedI have to upgrade to an ASA 5510 CSC, and the new license is generated, the file you sent me licensing, only seen this:Activation Code not required for this renewal. Please go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date (BASE: 09/04/2014, PLUS: 09/04/2014).This means that what I have not make any upgrades or license charge in the ASA? Does the automatic update is made?
View 1 Replies View RelatedThe model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies View RelatedWe want to buy a ISE-3315-K9 for 500 end-devices.In the price-list I found the ISE-3315-K9 but cannot find the base license: L-ISE-BSE-500=. (I think I need this license)Will the shipment of the ISE-3315-K9 includes a 3000 end-points base license (maximum support of the ISE-3315) or do I need to order the base 500 license seperately?
View 1 Replies View Related