Cisco :: Blocking Site On ASA 5505 Version 8.2(1) Base License Using CLI?
Jul 13, 2012basic step to blocking site on ASA 5505 version 8.2(1) base license using CLI
View 1 Replies
ADVERTISEMENT
Cisco Firewall :: ASA 5505 With Base License That Uses 3 VLAN
Jul 17, 2012I am working on ASA 5505 with Base License that uses 3 VLAN's.
-My VLAN 1 is for used for my home network.
-VLAN 2 is connected to the public Internet and my IP gets assigned by ISP dynamically.
-VLAN 3 is DMZ where I will have few VM's that would need access to and from the Internet.
I am looking to work with following:
1) 172.16.0.2 that sits on DMZ will need to access public Internet over port 80
2) Permit access from the Internet over port 3389 to 172.16.0.2
3) Permit any host on private VLAN (192.168.0.0 network) to access 172.16.0.2 over the port 3389
4) Permit second VM on the DMZ VLAN let say 172.16.0.3 to access public Internet on all ports. Access in to this host is not permitted.
5) For some reason DHCP hosts are NOT getting DNS (8.8.8.8) entry when IP hets assigned or renew. I have a statements below but it is not working.
Also, if ACL rules for VoIP are written correctly. The goal is to permit these ports (SIP related) to access VoIP router. [code]
Cisco Firewall :: Adding A DMZ On ASA 5505 With Base License
Dec 28, 2011I'm tring to setup a DMZ for a guest wireless off of a 5505. So this device has a base license. It has vlan1 and vlan 2 for inside and outside.Another vlan is configured to be a failover for the currently active wan connection. It is using the "no forward interface" command.Can I add another vlan as a DMZ if I use the "no forward interface" command? [code]
View 6 Replies View RelatedCisco Firewall :: Configuring ASA 5505 With Base License
May 11, 2011I have ASA 5505 with base licence. I configured NATing and VPN(site to site). All are working fine.My ASA is base license so i created 2 VLANS, one is inside and outside.Inside i am using 10.91.40.0/24 serie IP addresses.Below are the new requirements that i need to configre:
1. First 30 IP addresses only needs internet directly.( Servers and Management)
2. If remaining IPs likes to use web then traffic needs to forward one proxy server( where he gives user authentiation)
Cisco Firewall :: ASA 5505 - DMZ Configuration With Base License
May 24, 2011My ASA 5505 base license allows for three VLANs, the third one can only initiate traffic to one other VLAN (as specified by no forward interface vlan <number> on the third VLAN). This doesn't mean it can't "access" the other VLAN, it just can't initiate traffic to it. A lot of people get that wrong.Let's say you've got three VLANs, one is OUTSIDE, two is DMZ, and three is INSIDE. On the second VLAN would I enter the no forward interface as vlan 3, then set the name via the nameif command and everything will work just fine. The DMZ will not be able to initiate traffic to the INSIDE, but will to the outside, and assuming you have your ACLs and NAT set up properly, it will be able to respond to traffic from the INSIDE.
Would that be best practice or would I enter the "no forward" interface as in VLAN 1, thus is being able to respond to traffic from the outside as opposed to the inside.
I had a DMZ set up but since there was an intrusion into my network, I am building it again.
Cisco Firewall :: 5505 Which License Needed To Buy For Normal Base
Sep 22, 2012I have a couple of 5505's with base licenses. One of the two has a limited output when running the sho version command, as it has a restricted license. What license I would need to buy in order to bring it up to "normal" base license ?
View 1 Replies View RelatedCisco Firewall :: How To Block ARES With ASA 5505 Base License
Sep 1, 2011Well, I tried using the cisco configuration for ASA 5505 for blocking P2P: url...but this configuration only is usefull with programs like Kazaa, so I try this configuration to block ARES but the problem is that ARES try to make downloads from different ports, ¿How do I block ARES if there are sereveral ports ?
View 1 Replies View RelatedCisco Firewall :: ASA 5505 Base License - How To Get AnyConnect Working
Mar 29, 2012I have a base 5505 and would like to get AnyConnect working. To do that, would I have to first purchase either an essentials or premium license and then purchase the AnyConnect Mobile license?
View 1 Replies View RelatedCisco Application :: 11500 / Redirect SSL From Base Site To Different Page On Same SSL Site
Aug 24, 2011I'm attempting to redirect SSL from the base site to a different page on the same SSL site. I want to redirect https://10.4.16.54/* to[URL] . If I enter[URL], site loads, but if I enter simply https://10.4.16.54, it times out. The ssl_sharepoint service is my ssl_proxy_list.
content Sharepoint_https
flow-timeout-multiplier 10
sticky-inact-timeout 35
vip address 10.4.16.54
application ssl
[code]....
Cisco VPN :: ASA 5510 Implicit Deny Access Rule Blocking Site-to-Site VPN?
Apr 22, 2012I've setup a site to site vpn on an ASA 5510 using ASDM (as I have many times before) and the tunnel appears to be up but I am not able to pass traffic. When I run the packet tracer from my inside network to the remote destination network, it shows that it is blocked by the implicit deny ip any any rule on my inside incoming access list.
View 5 Replies View RelatedCisco :: Migrate WCS Base License To NCS 1.1?
Apr 3, 2013We are trying to migrate WCS base license to NCS 1.1 .We have procured the migration license .In the licensing guide , it is mentioned as "L-WCS-NCS1-M-K9 License first, before adding the licenses migrated from your WCS installation"
1)Whether we need to add this migration license in WCS before genrating XML file or
2)Before adding XML file in NCS we need to add this in NCS ..
Cisco WAN :: 1941 With IP Base License
Aug 7, 2012I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
Cisco VPN :: ASA5505 Blocking Remote Network / Site-to-site Vpn
Jun 28, 2011I have a site-to-site VPN already established, everything is working as it should. I'm trying to block the remote network from accessing our network since we only need to access theirs. I'm sure this is something very easy to implement with an ACL but I'm not sure where this rule needs to go. The VPN is on ASA 5505.
View 5 Replies View RelatedCisco Firewall :: 5510 CSC Base License
Jan 27, 2013We have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.
View 1 Replies View RelatedCisco WAN :: IP Base And Unified Communication License In 2921
Jun 30, 2012How to install IP base liecense and Unified communication liecense in 2921 router?
View 1 Replies View RelatedCisco Switching/Routing :: IP Base To IP Service License Of 3750x
Dec 8, 2012I am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies View RelatedCisco Switching/Routing :: WS-X3750-24P-L For LAN To IP Base Upgrade License
Mar 26, 2013Would like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies View RelatedCisco Firewall :: ASA5505 With Base License - Access From Dmz To Internal
Dec 18, 2011we have a cisco ASA5505 with base license and 3 interface configured. Internal 192.168.1.1/24 DMZ 172.16.0.1/24 Outside 20.20.20.20/24 The DMZ is configured to allow the traffic pass to the outside interface only (base license allow only traffic to one interface) in order to let clients on this network to browse internet. On the outside interface there's a nat configuration that let the port 443 to be natted to an in internal server. Is it possible to let the clients in DMZ to access to the internal server on port 443 from the outside interface?
View 3 Replies View RelatedCisco Switching/Routing :: 3750 - LAN Base License Limitations
Mar 3, 2013I am bringing up a 3750x and a 2911 to replace a 3745 router with switchport module. I was plannng on moving all the VLAN interfaces off the 3745 onto the 3750x and turning up EIGRP. I discoved the 3750 has the LAN Base license, so I can't run eigrp off of it. My question or worry now is, will the LAN base license prevent the switch from doing interface VLAN routing between the different VLAN's configured on it or will I have keep all the VLAN interfaces on the new router and just have a router on a stick setup?
View 4 Replies View RelatedCisco Firewall :: ASA5510 Renew CSC Base License After Grace Period
Oct 24, 2011we have a customer with a ASA 5510 with a CSC module in it. The device tells us the Base license has expired. The new license has been renewed - after - the grace period. The Trendmicro site tells us the Base license is valid until 21 october 2013 but the CSC refuses to acknowledge this. The module is able to fetch updates form the Internet so it does not look like a connection problem to me (it also has a plus license which is also valid till far into 2013 and that one works).Is it possible that the current license key is "dead" and the CSC expects a new license key because the grace period was expired?
View 1 Replies View RelatedCisco Switching/Routing :: WS-C3750X-24T-L License For Supporting IP Base / Services Feature Set?
Jan 7, 2012The model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies View RelatedCisco AAA/Identity/Nac :: Will Shipment Of ISE-3315-K9 Includes 3000 End-points Base License
Oct 11, 2011We want to buy a ISE-3315-K9 for 500 end-devices.In the price-list I found the ISE-3315-K9 but cannot find the base license: L-ISE-BSE-500=. (I think I need this license)Will the shipment of the ISE-3315-K9 includes a 3000 end-points base license (maximum support of the ISE-3315) or do I need to order the base 500 license seperately?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: 2000 Base Concurrent Users Exceed License Allowable Count
Mar 25, 2013Getting the following alarm from my ISE:Cause:Base License Enforcement Details: Base concurrent users exceed license allowable count.Currently only using 1656 out of 2000 base licenses so I'm not sure what the issue is. Running 1.1.2.145 patch 3.
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 5548 Rebooting Continually After Installing L3 Base License
Jul 30, 2012we recently purchased L3 daughter cards (N55-D160L3-V2) for our 5548UPs along with the LAN Enterprise Services licenses (N55-LAN1K9).
I installed the cards and Ent Svcs lic this past weekend and everything went well excep that I couldn't enable the EIGRP feature .. apparently EIGRP requires the LAN Base (N55-BAS1K9-BUN) license even when you have the Enterprise lic installed, so I was able to dig up that license eventually (which comes with the L3 daughter card, incidentally). Another side effect of not installing the Lan Base lic is that the L3 card/module will be in an "offline" state until the Lan Base lic is installed. Either way, everything was working normally in L2 mode at this time.
So, here I was thinking I was ready to proceed with enabling L3 - this morning I installed the LAN Base license on one of the 5548s which apparently triggered the L3 Daughter card module to go active and triggered a switch reboot. Ok, not that big of a deal, knew that was probably coming. I expected the switch to come back up normally .. NOPE. The switch went into a continual reboot cycle where the console prompt would appear, then about 30 seconds later, would reboot again.
I finally ended up re-installing the original L2 card and the switch came right up. I see that LAN Base and LAN Enterprise are both still installed as well.
What have I done wrong here? Why did the switch go into a continuous reboot cycle once I installed the LAN Base license?
Here are more details :
Software
BIOS: version 3.5.0
loader: version N/A
[Code]....
Cisco VPN :: 5505 - Site To Site Connected But Cannot Ping Remote Site
Oct 11, 2011cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedCisco VPN :: ASA 5505 / Site To Site Vpn With One Site Always Initiate A Tunnel?
Feb 7, 2011I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies View RelatedCisco VPN :: ASA 5505 Site To Site Connection / Remote Site?
Mar 6, 2011i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View RelatedLinksys Wireless Router :: WRT45G Version 7 Reboot When Want To Access In Web Base Utility
Sep 22, 2011i have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
View 4 Replies View RelatedCisco VPN :: 2901 / 2921 / 5505 ASA - Router Versus Firewall Site To Site VPN?
May 30, 2013I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
Cisco VPN :: 5505 Connection To Mapped File Shared Dropping On A Site-to-Site VPN
Nov 27, 2011We've just deployed a site-to-site VPN using a 5505 ASA on the client's site and a checkpoint Nokia FW on our site. Everything seems to be fine except that the user's connections to their file shares seem to be intermittently dropping. One minute the connection to the shares is there, next thing it's lost. There is no logic to it because no two users are experiencing issues at the same time, as a matter of fact even on the same PC where a user has access to 3 shares on 3 different servers, one could be showing as connected whereas the other two be dropping. [code]
As you can see the Duplex and Speed are set to auto, I've rectified this since then and I'm keeping a close eye on the output errors, and collisions. However, I'm afraid that this did not rectify the issue and the users are still experiencing intermittent connection dropping to their file shares over the VPN!
Cisco Firewall :: ASA 5505 / Site To Site VPN Using Public Addresses On Local Network
Jul 28, 2011I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
Cisco Firewall :: ASA 5505 Site To Site RTP Traffic Is Hitting Deny All Rule?
Aug 13, 2012Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code].....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
Cisco Application :: ANM 4.3 Demo Version / Unable To Install License
Sep 18, 2011I am installing the Demo version of ANM 4.3 on a virtual machine.The install was successful, however when i try to import the demo licence from my laptop to the server it does not allow me to tftp the file to the server.[URL]
View 1 Replies View Related