Cisco Firewall :: ASA 5505 Site To Site RTP Traffic Is Hitting Deny All Rule?

Aug 13, 2012

Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.

Currently the rules are as follows
 
 Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny

 [code].....
 
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.

View 2 Replies


ADVERTISEMENT

Cisco :: ASA 5505 Site To Site RTP Traffic Is Hitting Deny All Rule?

Aug 14, 2012

Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.

Currently the rules are as follows

Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny

[code]....

It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.

View 3 Replies View Related

Cisco VPN :: ASA 5510 Implicit Deny Access Rule Blocking Site-to-Site VPN?

Apr 22, 2012

I've setup a site to site vpn on an ASA 5510 using ASDM (as I have many times before) and the tunnel appears to be up but I am not able to pass traffic.  When I run the packet tracer from my inside network to the remote destination network, it shows that it is blocked by the implicit deny ip any any rule on my inside incoming access list.

View 5 Replies View Related

Cisco VPN :: ASA 5505 / Site 2 Site VPN With Backup Peer Not Able To Send Traffic

Mar 13, 2011

I have 2 ASA 5505 Firewall, I Configured Site 2 Site VPN no both the fitrewall, as i have a dual ISP, i am able to create the tunnel with primary but once my primary is down i am not able to create the tunnel with back up ISP. During the troobleshoothing by typing Show isakmp sa and Show ipsec sa, i can see my tunnel is up, but not able to decap the packets.
 
As it will look like
 
#pkts encaps: 15, #pkts encrypt: 15, #pkts digest: 15      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0      #pkts compressed: 0, #pkts decompressed: 0      #pkts not compressed: 15, #pkts comp failed: 0, #pkts decomp failed: 0      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0      #send errors: 0, #recv errors: 0

View 4 Replies View Related

Cisco VPN :: ASA 5505 Site-to-Site VPN Tunnel Up But Not Passing Traffic

Apr 3, 2013

I do have a 5505 up and running, and passing data... url...Now I am trying to get a IPSEC VPN tunnel working.I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
 
The networks concerned: name 10.0.0.0  Eventual  (HQ Site behind Firewall)name 1.1.1.0  CFS  (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)name 2.2.2.0  T1  (Remote site - Outside interface of 5505: 2.2.2.2)name 10.209.0.0  Local  (Remote Network - internal interface of 5505: 10.20 9. 0.3)  On a ping to the HQ network from behind the ASA, I get port map translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
 
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work. [code]

View 22 Replies View Related

Cisco VPN :: ASA 5505 Site-to-site Vpn Not Passing Traffic

Feb 4, 2011

I've setup a site-to-site vpn between 2 5505s, with 1 subnet per site directly behind the ASAs.The VPN establishes connection successfully, but i can only access resources from site2 to site 1. E.g. I can ping or rdp from a server in site2 at IP 192.168.3.250 to a site1 server at IP 192.168.10.250. I cannot make the opposite connection, i.e. 192.168.10.250 to 192.168.3.250.

View 2 Replies View Related

Cisco Firewall :: Pix 506e Passing Traffic Even With A Deny Ip Any Any Rule

Sep 20, 2012

So I was doing some testing with my BB Playbook where I wanted to see what outside connections it tried to make during startup and whatnot. I have a pix 506e running 6.3(5). I created an simple 'deny ip any any' access list on the inside interface so that the Playbook doesn't actually make any connections, but I set up a 'capture' on the inside interface accepting 'ip any any' to see what kind of traffic I could see heading outbound from the Playbook. Well, it started off showing attempts to query DNS (and failed, naturally), but then after a couple of minutes, it tried to connect to a couple of IPs over port 443 and actually got a response!!! For the life of me, I can't figure out how this can happen. NO traffic should be allowed outbound due to my explicit 'deny' rule, but for some reason some traffic on port 443 made it past the firewall and got a response back. There are no other rules in the access list except the 'deny' rule. My PIX configuration is quite simple and I cannot see anything that would allow the Playbook traffic to circumvent the access list.

I've come to think that either RIM has found away around Cisco access-lists, or there is a bug in the Pix OS. I know it's an old appliance/OS, but still. I wouldn't think it could be THAT easy to bypass the firewall.

View 4 Replies View Related

Cisco VPN :: 2901 / 2921 / 5505 ASA - Router Versus Firewall Site To Site VPN?

May 30, 2013

I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
 
1) what is the different to build site to site VPN between router and firewall ?

2) which is the best choice if using in site to site VPN connection ? 

View 9 Replies View Related

Cisco Firewall :: ASA 5505 / Site To Site VPN Using Public Addresses On Local Network

Jul 28, 2011

I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
 
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.

View 5 Replies View Related

Cisco Firewall :: ASA 5505 - Unable To Access Certain Ports Over Site To Site VPN

Jan 16, 2013

We have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
 
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
 
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
 
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
 
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
  
Building configuration...
  
Current configuration : 23648 bytes
!
version 12.4
no service pad

[Code].....

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Site To Site VPN Route From Multiple LANs?

Dec 19, 2012

I've set up a standard site-to-site VPN between 2 ASA 5505s and the VPN is working fine for traffic between these ASAs and computers which are in the same LANs.but when I'm trying to connect to computers which are in another VLAN I have a problem.

View 1 Replies View Related

Cisco VPN :: Site To Site VPN IPSEC Tunnel From ASA 5505 To Clavister Firewall

Nov 20, 2012

I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
 
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
 
All these remote networks are at the Main Site Clavister Firewall.

View 1 Replies View Related

Cisco Firewall :: Max Number Of Clients And Site To Site VPN Tunnels On ASA 5505

Aug 15, 2012

I wanted to know the maximum VPN client sessions (using the Cisco VPN  client) and Site-to-Site VPN tunnels that I can connect to my ASA 5505  simultaneously.
 
In other words, if I have x VPN clients and y Site-to-Site  tunnels, at any time, does x + y have to be <= 10 (Total VPN Peers)?  If yes, can I upgrade to the security plus license to increase the Total VPN Peers to 25?

Licensed features for this platform:
Maximum Physical Interfaces    : 8
VLANs                          : 3, DMZ Restricted
Inside Hosts                   : Unlimited
Failover                       : Disabled
VPN-DES                        : Enabled
[Code]...

View 3 Replies View Related

Cisco Firewall :: ASA 5505 Setup A Site To Site Tunnel?

Nov 13, 2012

I have a 5505 asa code version 8.3(2). Trying to set up a site to site tunnel with someone and he is asking if I can use ike v2. How do I go about setting up the tunnel to use ikev2? Is ikev2 an option with site to site tunnels?

View 5 Replies View Related

Cisco Firewall :: Site-to-Site VPN Between ASA 5510 And 5505 Configuration

Apr 18, 2013

I am not very experienced with Cisco networking.

Here is the situation.
 
Site A - headquarters 192.168.1.x
Site B - remote office 192.168.20.x
Site C - remote office 192.168.30.x
 
Site A - ASA 5510
Site B - ASA 5505
Site C - ASA 5505
 
Site-to-site VPN is established and works between A and B, A and C. Users would like to establish a tunnel between B and C to work on a common project and the data is on Site B.
 
I tried configuring the S2S VPN with pre-shared keys on both firewalls at sites B and C but in the end it is not established (I cannot ping either side). I used the Wizard interface multiple times and one time the CLI. I generally followed the settings chosen between the headquarter and the individual remote sites and tried to replicate them. Obviously I have made a mistake somewhere.
 
Could there be any limitation on the ASA 5505 in terms of licensing and the number of S2S tunnels?

View 7 Replies View Related

Cisco Firewall :: Site To Site VPN Between PIX515 And ASA 5505 With Dual ISP?

Apr 13, 2011

We have got site to site VPN configured between local site with PIX515 6.3(5) and remote site with ASA 5505 7.2(4) . Because of very unreliable internet connection in remote site , we have added new ISP link  which we want to use as redundant link .i understand ASA 5505 can be configured with two ISP link with SLA monitor method for redundancy as per this document ,[URL]
 
my question is how do i set up this pix 515 to have redundant VPN tunnel with remote site (when primiary ISP link fails in remote site and  secondary ISP links takes over ) .  I was thinking of using   PIX 515 with 2 peers in same crypto map used for that sepcific site to site vpn tunnel,not sure that is the right way or not though.But how would i configure ASA 5505 to use backup interface(where secondar isp router conects ) to particitae in Site to site Tunnel .

View 4 Replies View Related

Cisco Firewall :: ASA 5510 / 5505 - Site-to-site VPN One Way Access

Dec 12, 2011

We have a Cisco ASA 5510 at our main office that makes connection with a 5505 at our other office using site to site VPN. (works)
 
Now for the question,
 
we want to access our other office from the main office but we wont want them to have access to our servers etc. so basically we want to control them but they shouldn't have the rights to control us.

Is this possible with a site to site VPN? and how to do it.

View 7 Replies View Related

Cisco Firewall :: ASA 5505 Site-to-Site With UC540 Routing?

Dec 4, 2012

We are setting up a new phone system using the UC540 with a VPN connection between 2 buildings using 2 Cisco ASA 5505's at either end.The problem I am having is getting the phones at the remote site to connect to the UC540 at the main site.
 
Phones/Computers (10.0.1.0/24) -- ASA -------------VPN Tunnel------------- ASA -- UC540 -----------Data Vlan1 (10.0.0.0/24)
|------Voice Vlan100 (10.1.1.0/24)
 
What i am told by UC500 support is that the phones at the remote site will connect if they have connectivity to the TFTP subnet on the UC540, which is 10.1.10.0/30 I added the static route on the ASA and I can ping the 10.1.10.1 TFTP server on the UC540 from the ASA, but not for any other device on the 10.0.0.0/24 network, such as the DC.  I added the static route there and was able to ping, so something in the ASA seems to be preventing it. 
 
I also can't seem to get the ASA at the remote site to ping 10.1.10.1.  I've tried adding the static route there in hopes it would forward it through the VPN tunnel.

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Site To Site VPN Keep Dropping?

Feb 1, 2012

I have an issue with my site to site VPN. I have 4 sites connected  to my main HQ site via Cisco ASAs 5505 firewalls. The problem is that once and then the sites disconnected from my main site. This disconnection is not happening at the same time for the the 4 sites. For example, it might be different site each time disconnected.

View 7 Replies View Related

Cisco Firewall :: Site To Site VPN Configured On ASA 5505

Dec 2, 2012

I have a site to site VPN configured on a asa5505. The tunnel is up and the interesting traffic is successfully being encrypted. The issue is that when inbound traffic originating from a subnet outside of the encrypted range destin to the subnet within the encrypted range, the return traffic is sent into the tunnel and obviously fails.When traffic from 1.1.1.0/24 to 10.2.2.0/24 traverse the firewall the return traffic goes into the tunnel but it doesn't have the correct match parameters?Am I missing something?  I'm expecting that only traffic matching the crypto map will use the tunnel and all other traffic will utilize the default route.

View 3 Replies View Related

Cisco VPN :: Configure A Site-to-Site VPN In ASA 5505 Firewall

Dec 13, 2010

I'm trying to configure a Site-to-Site VPN in a Cisco ASA 5505 firewall which is behind an ISP router (Cisco 800 Series) configured in routing mode (not bridging) and with a static nat of all the ports to the firewall (avoiding bridging mode of the router). [code]

View 12 Replies View Related

Cisco VPN :: Site To Site With ASA 5505 And Sonic Firewall

Aug 27, 2009

I'm trying to establish a vpn tunnel with a sonic firewall.  We've checked both ends for differences and they are the same.  PFS has been disabled on both ends.  I'm seeing this in the logs.
 
%ASA-3-713119: Group = x.x.x.x, IP = x.x.x.x, PHASE 1 COMPLETED
%ASA-5-713068: Group = x.x.x.x, IP = x.x.x.x, Received non-routine Notify message: No proposal chosen (14)

[Code].....

View 4 Replies View Related

Cisco VPN :: 5505 - Site To Site Connected But Cannot Ping Remote Site

Oct 11, 2011

cisco products and am struggling getting a VPN going between an ASA 5505 and 5510.  I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).

View 11 Replies View Related

Cisco Firewall :: ASA 5505 / Block Internal LAN And Internet Traffic Except LogMeIn Site?

Sep 12, 2011

I have configure Cisco 5505 as layer 2 firewall mode. I have vendor machine connected  to Cisco ASA 5505 on port 2 as VLAN2 inside then VLAN1 outside connected to my internal network on layer 2 cisco 2960 switch. This machine needs access only to LOGMEIN then block all internal/internet traffic. 
 
vendor machine on vlan 2 inside >> Cisco ASA 5505 vlan1 outside  >> layer2 switch >> internal LAN >> Cisco 5520 main FW >>> INTERNET

View 1 Replies View Related

Cisco VPN :: ASA 5505 / Site To Site Vpn With One Site Always Initiate A Tunnel?

Feb 7, 2011

I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.

View 3 Replies View Related

Cisco VPN :: ASA 5505 Site To Site Connection / Remote Site?

Mar 6, 2011

i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?

View 1 Replies View Related

Cisco VPN :: 1800 Site-to-Site VPN Tunnel Bandwidth For Voice Traffic

Jun 22, 2011

I have some challenges with a VPN config I recently setup for a client.I have at the HO the following:

- 1800 router
- Avaya phones and Gateway
- 1MB radio internet access
 
At the BO(branch office), i have:

- 871 Router
- Avaya phones
- 256k internet bandwidth
 
The only reason we setup the VPN in the first place was for the phones at the BO to be able to connect to the gateway at the HO and also able to make calls and receive calls as if the phones were at the HO.The phones at the BO successfully register to the HO, but are unable to recieve calls and dial out. Everytime I try to make a call, the phone displays a "connecting..." message. [code]

View 2 Replies View Related

Cisco VPN :: ASA 8.2 - Site-to-Site VPN Stops When Traffic Volume Rekey Reached

Jan 12, 2010


We have several site-to-site IPSec VPN's setup.

All are running on ASA's 8.2(1).

All have a Security Association Lifetime (Time) of 8 hours.
All have a Security Association Lifetime (Traffic Volum) of 4608000 KiloBytes.

We have an issue when we do Oracle logshipping between the sites.

This triggers the Traffic Volume rekey as can be seen by this entry in the logs: -

%ASA-7-702307: IPSEC: An inbound L2L SA (SPI= 0x169FA1C1) between and (user= ) is rekeying due to data rollover.

However it does not appear as if the renegotiation is occurring properly. Within 10 to 15 minutes data stops being transmitted along the link, even though the IPSec tunnel still appears up in the ASDM GUI.

The 'fix' for this is that we are using is to login to the ASDM GUI and bounce the link by going to Monitoring => VPN => VPN Statistics => Sessions => IPSec Site-to-Site. Then select the appropriate VPN tunnel and click on 'Logout'. This forces a link renegotiation which works fine.

I have attached a logfile from the local ASA (there's nothing in the logfile of the remote ASA until we bounce the VPN tunnel).

View 10 Replies View Related

Cisco Wireless :: Configuring 5508 At Remote Site To Tunnel Traffic From WLC At Main Site?

Sep 20, 2012

At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG).  In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG".  None of the SSIDs are "anchored".
 
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs.  This site contains two customers.  One customer is the Main customer with the second customer leasing space.
 
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan).    I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
 
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500.  It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site.  This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
 
For my test, I am starting simple.  I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low).  I have anchored this test WLAN to that controller.  At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site.  I am unable to obtain an IP address from the remote site.  I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?

View 5 Replies View Related

Cisco VPN :: 876 ISR / Traffic From Easy VPN Client To Remote End Of Site-to-site?

Apr 27, 2011

A user with Easy VPN client connects to a 876 ISR (router A). This router also has a site-to-site VPN to another 876 ISR (router B). What I want to achieve is that the user dials in to router A and can access the network on the remote end of the site-to-site tunnel (router B) In diagram:
 
user (192.168.18.x) - Easy VPN - Router A (192.168.16.x) - sitetosite - Router B (192.168.17.x)
 
I have added routes in router B to the 192.168.18.x network with router A as next hop, but I can't reach the other segment.

View 1 Replies View Related

Cisco VPN :: ASA 5520 - Routing Traffic Between Two Site To Site Tunnels

Feb 24, 2013

I am trying to establish routing between two Site to Site vpn tunnels, both of which are terminating on the same outside interface of my Cisco ASA.
 
find attached Network Diagram for the same. All Firewalls used are Cisco ASA 5520.
 
Both VPN tunnels between Point A and Point B, Point B and Point C too are up. I have enabled Same security level intra interface permit command also.
 
How do i enable traffic originating from LAN Subnets behind Point A to reach LAN Subnets behind Point C without having to create a Seperate tunnel between Point A and Point C

View 5 Replies View Related

Cisco VPN :: ASA 5580 Site To Site VPN With Netgear Established But No Traffic

Mar 24, 2011

I have set up a site to site VPN from a Cisco ASA 5580 to a Netgear  FVS318v3 using 3DES, MD5, GH 2 and preshared key, My VPN Tunnel is always up, I can see on the netgear and firewall ASA that the connection VPN is established at both phase 1 and phase 2 level, but no traffic is flowing through the tunnel sometimes. The only way I can see the traffic passing, it is reload the tunnel on the firewall netgear.the configurations on the firewalls are same.

I can see the requests of the ASA Red_Lan to server located at the remote site, behind the Netgear Firewall and observe traffic on the ASA but on the outside/inside interfaces of the firewall Netgear there are not traffic. Is necessary to configure and others parameters for VPN?

View 1 Replies View Related

Cisco Routers :: Routing All Traffic To Vpn Site-to-site With SRP527W

Aug 21, 2011

I'd like to create a site-to-site vpn between an SRP527 and an other vpn gateway. The problem is i don't see how to route all traffic from the local network (network defined by the lan ip interface of the SRP527) to the other vpn gateway? It seems to be only possible to define the destination network (accessible via the vpn) with ip/mask (but only for "small" network: for exemple i tried with 10.2.0.0 mask 255.255.0.0 and it's ok but i tried with 10.0.0.0 mask 255.0.0.0 -> it's not working. I obtain the message "invalid ip")

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved