Cisco Wireless :: Configuring 5508 At Remote Site To Tunnel Traffic From WLC At Main Site?
Sep 20, 2012
At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG). In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG". None of the SSIDs are "anchored".
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs. This site contains two customers. One customer is the Main customer with the second customer leasing space.
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan). I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500. It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site. This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
For my test, I am starting simple. I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low). I have anchored this test WLAN to that controller. At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site. I am unable to obtain an IP address from the remote site. I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?
View 5 Replies
ADVERTISEMENT
May 19, 2011
It's been a long time since I played in Cisco CLI.Using a Cisco 506 Firewall 6.3(4) PDM 1.0?Problem is I created a site to site tunnnel with a vendor and since then our remote VPN does not work. Completely times out so I am sure I broke something in the crypto map or something similar.
Tunnel is policy 10 using access-list 101
Remote VPN is Policy 20
Config Below:
: Saved:PIX Version 6.3(4)interface ethernet0 10fullinterface ethernet1 10fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password XLk0qAaMaA6kjvA6 encryptedpasswd VeCrsQbWdIFPwnny encryptedhostname RMS-DR-PIXdomain-name RMS.Localfixup protocol dns maximum-length 512fixup protocol ftp 21fixup protocol h323 h225 1720fixup protocol h323 ras 1718-1719fixup protocol http 80fixup protocol rsh 514fixup protocol rtsp 554fixup protocol sip 5060fixup protocol sip udp 5060fixup protocol skinny 2000fixup protocol smtp 25fixup protocol sqlnet 1521fixup protocol tftp 69namesobject-group network FTP_Clients description FTP Client PCs network-object host 192.168.xxx.xxx network-object host
[code]....
View 4 Replies
View Related
May 21, 2011
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24
View 5 Replies
View Related
Jun 22, 2011
I have some challenges with a VPN config I recently setup for a client.I have at the HO the following:
- 1800 router
- Avaya phones and Gateway
- 1MB radio internet access
At the BO(branch office), i have:
- 871 Router
- Avaya phones
- 256k internet bandwidth
The only reason we setup the VPN in the first place was for the phones at the BO to be able to connect to the gateway at the HO and also able to make calls and receive calls as if the phones were at the HO.The phones at the BO successfully register to the HO, but are unable to recieve calls and dial out. Everytime I try to make a call, the phone displays a "connecting..." message. [code]
View 2 Replies
View Related
Feb 20, 2013
I have a situation where I need to have remote users vpn into my ASA 5510 and then turn around and hit a site to site tunnel. Now when I am in our office I can hit the site to site vpn fine. When I am at home and vpn to the asa I can not get to the site to site resources. Do you see where my config is incorrect? result of the command: "show run"
ASA Version 9.1(1)
!
hostname xxxxx
domain-name xxxx
enable password xxxxx
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
[ code]....
View 3 Replies
View Related
Feb 6, 2012
On remote site I have Cisco ASA5505, on cental site I have Cisco 2811 router, working site-to-site VPN tunnel. [code]
View 1 Replies
View Related
Apr 3, 2013
I do have a 5505 up and running, and passing data... url...Now I am trying to get a IPSEC VPN tunnel working.I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
The networks concerned: name 10.0.0.0 Eventual (HQ Site behind Firewall)name 1.1.1.0 CFS (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)name 2.2.2.0 T1 (Remote site - Outside interface of 5505: 2.2.2.2)name 10.209.0.0 Local (Remote Network - internal interface of 5505: 10.20 9. 0.3) On a ping to the HQ network from behind the ASA, I get port map translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work. [code]
View 22 Replies
View Related
Jun 16, 2011
I want to configure QoS for voice traffic over a site-to-site VPN tunnel. I have a Cisco 851 router on the branch end and a Cisco 1800 router at the HQ. The setup is an Avaya Gateway located at the HQ and the idea is that the phones at the branch office are connected over the VPN tunnel to the gateway at the HQ.
I have a 1MB internet link at the HQ from a service provider and 256kbps internet link (from a different service provider) at the branch office. The branch office has just 3 users.
View 12 Replies
View Related
Apr 27, 2011
A user with Easy VPN client connects to a 876 ISR (router A). This router also has a site-to-site VPN to another 876 ISR (router B). What I want to achieve is that the user dials in to router A and can access the network on the remote end of the site-to-site tunnel (router B) In diagram:
user (192.168.18.x) - Easy VPN - Router A (192.168.16.x) - sitetosite - Router B (192.168.17.x)
I have added routes in router B to the 192.168.18.x network with router A as next hop, but I can't reach the other segment.
View 1 Replies
View Related
Dec 6, 2011
Trying to implement HREAP over WAN between main and remote site. The WLC4402 is on main site. There will be a secondary DHCP at the remote site. Does the switch at the remote site any preparation?
View 4 Replies
View Related
May 18, 2012
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies
View Related
Feb 7, 2011
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies
View Related
Jun 17, 2012
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies
View Related
Jun 13, 2012
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
View 1 Replies
View Related
Oct 11, 2011
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies
View Related
Apr 15, 2012
We have a Site that is connected via Wireless Bridge to the Main Site, the site is on separate VLAN with Cisco 3560 switch. The main site has 6509 swith. Configuration as per attached diagram. We are connecting a fiber between the remote and the main site and adding a 3560E switch at the remote site, however we would like to keep the wireless connection as a backup in case the fiber is severed the wireless will be availble. Attached diagram shows detailed cofiguration. I would like to know what should I change to make this working. STP is enabled on all switches.
View 3 Replies
View Related
Mar 6, 2011
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies
View Related
Oct 18, 2012
On one of our branch locations ASA, I have a L2L VPN setup we are adding wireless to this remote location, and the AP's will talk back to the controller at HQ. The AP's are on the downstream L3 switch, and they have been placed on the mgmt network. It's definitely not ideal to have these AP's on the mgmt network, but for now that is how it is setup.
From HQ (163.122.x.x) I can ping and reach the ASA (10.200.2.1, and the downstream L3 switch 10.200.2.100, but when I ping one of the AP's, I get timeouts and and the following error on the ASA:%ASA-3-305005: No translation group found for icmp src outside:10.205.216.73 dst mgmt:10.200.2.152 (type 8, code 0)
It appears it's a NAT issue on the ASA, but I'm confused on what I need to change. Why can I ping the ASA and the switch from HQ, but not the AP's which reside on the same mgmt network? I don't really need it to NAT, just to pass the connections. I currently only have the following two NAT statements in the configure
[code]...
View 1 Replies
View Related
Mar 11, 2012
I have a setup like this:
A central WLC 5508 running code 7.2 with management vlan 10 ( range 10.10.10.0/24), corp-user vlan 100 (10.11.10.0/24) with WPA2 key, guest vlan 200 (192.168.0.0/24, on local dsl modem) with WPA2 key...
A remote WLC 5508 with code 7.2 with management vlan 10 (range 10.20.10.0/24), corp-user vlan 101 (10.21.10.0/24) with WPA2 key and guest vlan 201 ( 192.168.0.0/24, on local dsl modem) with WPA2 key
corp ssid "Corp-user" on both sites
Guest ssid "Guest" on both sites
Intention is that the AP's (3500) on the remote site should fail over to the central WLC in case of any failure on the remote WLC and that the users could remain in their local vlan.
What kind of configuration would make this work?
View 8 Replies
View Related
Mar 15, 2011
I have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
View 1 Replies
View Related
Oct 17, 2012
ASA is configured with the VPN site to site using the wizard, created the Public IP of contivity, local and remote LAN . I attached the configuration. In contivity have the following settings: Not able to communicate both subnets.Do I need to configure IP subnets and published in the contivity as was done in the ASA?
View 3 Replies
View Related
Jan 14, 2013
We have a 5508 controller in main site.Which has two ports connected to local network.Management VLAN 500 is untagged and mapped to Port 1.All other interfaces are including 501 to 507 are mapped to Port 2.We have a SSID that is mapped to VLAN 501 interface , which successfully can be joined in main site.We connect an AP to remote site ;We have a remote site VLAN 115 which can be reached from main site.We connect an AP to access vlan 115 port on the remote site , we had described option 43 , so AP can successfully finds controller in local mode.
AP gets ip from VLAN 115 , can setup connection / ping controller successfully.There is a wide area connection between remote and main site.No trunk setup , the whole remote site is vlan 115.However when the client is trying to connect the test SSID , client cant get connected nor get ip address.Local switching is disabled.For this setup , client comes to AP as a requested , AP tunnels traffic to controller from vlan 500 , controller lets the client get into wired platform from VLAN 501.
View 25 Replies
View Related
Jun 3, 2013
We have a Cisco ASA 5505 at our CORP location, which I have configured the Site2Site VPN to our COLO with a Juniper SRX220h, the site to site works fine, but when users access the Cisco VPN client from home, they cant ping or SSH through the Site2Site. Contacted JTAC and they said its not on their end, so I tried to contact Cisco TAC, no support. So here I am today, after for the 3 days (including Friday last week) of searching the Internet for over 6hrs a day, and trying different examples of other users. The VPN client show the secured route to 10.1.0.0. [code]
View 19 Replies
View Related
May 28, 2012
I have a ASA 5510 that has multiple site to site VPNs. I need to create an additiona site to site VPN but only allow 1 host to access and traverse the tunnel. The network is on a 192.168.5.x but the host that will need to access this tunnel needs to be on a 172.16.33.x network. I dont want any other traffic allowed to access or traverse the VPN tunnel for this host. How can I set this up?
View 33 Replies
View Related
Dec 19, 2011
As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies
View Related
Apr 30, 2012
Need to know the step by step procedure for monitoring site-to-site VPN tunnel (up/down) using SNMP on Cisco ASA 5505.
View 1 Replies
View Related
Apr 24, 2013
I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers. But now i need to access internet on site B router sitting on site A router. So that if i run traceroute from A site machine then the gateway by which internet passing through shows the ip of site B.
The Architecture of our both site routers :
Site A 10.1.11.0-----Router A 172.18.12.1-----VPN tunnel----Router B 172.18.12.2-----Site B 10.4.11.0
/////Create IKE policy
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
[Code] .....
View 10 Replies
View Related
Apr 30, 2013
I have an ASA 5510 8.2(5) in Site1 and a ASA 5505 8.2(1) Site2 they are setup with a site to site tunnel.Each site has VPN clients that connect and I would like to allow clients from both sides access to servers on the other side of the site-to-site tunnel.
I enabled same-security-traffic permit intra-interface I also added the remote networks to access-list that is doing the split tunneling. [code]
View 33 Replies
View Related
Dec 1, 2011
How can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel? I'm using an ASA5520 running 8.04.
I have four hosts say: 10.240.1.1-10.240.1.4
They need access to two different networks:
205.100.150.0
140.175.200.0
I woud like to NAT them as something like:
7.5.210.1
7.5.210.2
7.5.210.3
7.5.210.4
View 1 Replies
View Related
Feb 17, 2013
We have configured a site to site tunnel from our ASA to another organizations Cisco 3030. It appears to have just one way initiation. We can do a ping to a device on the remote site and it will ping just fine. however, when the tunnel needs to be initiated from the remote site, it will not work until we have initiated the tunnel and then everything works.
I continue to see Error processing payload: Payload ID: 1 errors on the ASDM logs.It appears that all the configuration is in place because we can in fact establish the IPSec tunnel unidirectional. And once established, traffic can flow bidirectional.
View 1 Replies
View Related
Nov 20, 2012
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
View 1 Replies
View Related
Dec 12, 2012
We have approx 40 branch offices - all of which are connected to a single core site over VPN Tunnels using various gear. At one particular site, we are having issues with the tunnel dropping sporadically throughout the day - some days it happens 10 times, some days it happens none. This just randomly started happening two weeks ago, without any changes taking place. Since it started happening, I have upgraded the code to latest versions, but still the issue persists. This particular site has a 2901 and connects back to a 2951.
Below is the output from:
debug crypto ipsec
debug crypto isakmp
[code].....
View 1 Replies
View Related
Nov 28, 2012
I have a situation where the site-to-site tunnel is already established using PPTP IPSec VPN with non Cisco Gateways terminating the link on each end. These non Cisco Gateways do not support L2TP tunneling, and there is no plan to change them.Beyond the Gateways on both ends, we have a Cisco 4500 series switch. We need to forward the 802.1q tagged VLANs between the two sites. Is it possible to use 802.1Q tunneling in this case, going via a PPTP tunnel ?
Cisco's setup uses dot1q-tunnel over a L2protocol-tunnel to preserve the original client VLAN tagging, so does this mean that the only option we have is to setup a L2TP tunnel at the Cisco device endpoints, and have that tunnel go through the existing PPTP tunnel (established between the 2 non Cisco VPN Gateways) ?
View 1 Replies
View Related
