Cisco VPN :: 5520 Requirement To Terminate Site-to-site VPN From Remote Site

Jun 17, 2012

We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?

View 1 Replies


ADVERTISEMENT

Cisco VPN :: ASA 5520 / Routing Site-to-Site VPN To Remote Users?

Oct 29, 2011

We have a site-site and remote vpn configured in same interface in ASA 5520 ( software version 8.3  ). When Remote vpn users try to connect to computers located on the distant end of site-site VPN, their request failed. I tried No-Nat between  remote vpn private IP to the remote site private IP, also stated the same in Split tunneling. I cant find even the tracert, ping also timed out.

View 7 Replies View Related

Cisco VPN :: 5510 Site To Site VPN Access To Servers With Overlapped Remote Site

May 18, 2012

I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only  My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.

View 2 Replies View Related

Cisco VPN :: 877 / How To IPsec Site To Site Vpn Port Forwarding To Remote Site

Jun 13, 2012

The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
 
Below are my configure on the Cisco 877 in site A.  
 
Building configuration... 
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad

[code]....

View 1 Replies View Related

Cisco VPN :: 5505 - Site To Site Connected But Cannot Ping Remote Site

Oct 11, 2011

cisco products and am struggling getting a VPN going between an ASA 5505 and 5510.  I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).

View 11 Replies View Related

Cisco VPN :: How To Terminate Site-to-site Connection On ASA 5510

Oct 3, 2012

I would like to know if there is any command that i can use to terminate a site-to-site connection and restart it whenever i want to.I don't want to use the shut down command since i use the specific interface as an exit point to the internet.

View 4 Replies View Related

Cisco VPN :: ASA 5505 Site To Site Connection / Remote Site?

Mar 6, 2011

i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?

View 1 Replies View Related

Cisco VPN :: Establish Site To Site IPSec Tunnel Between ASA 5520 And 3030?

Feb 17, 2013

We have configured a site to site tunnel from our ASA to another organizations Cisco 3030.  It appears to have just one way initiation.  We can do a ping to a device on the remote site and it will ping just fine.  however, when the tunnel needs to be initiated from the remote site, it will not work until we have initiated the tunnel and then everything works.
 
I continue to see Error processing payload: Payload ID: 1 errors on the ASDM logs.It appears that all the configuration is in place because we can in fact establish the IPSec tunnel unidirectional.  And once established, traffic can flow bidirectional.

View 1 Replies View Related

Cisco VPN :: What Are Possibilities That Exist For Running Site-to-site Vpn In Environment 5520

May 23, 2013

What are the possibilities that exist for running a site to site vpn in our environment with the following infrastructure Cisco ASA 5520 - running on a multiple context mode
 
-Cisco 3750 switches
-Microsoft TMG
 
I believe these options are limited in terms of providing end point for VPN.Is there a VPN module that we can buy for 5520 to run IPSEC VPN?

View 2 Replies View Related

Cisco VPN :: ASA 5510 - AnyConnect Users Cannot Access Remote Office Over Site-to-site

Jul 15, 2012

we have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.

Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4

Site A internal: 192.160.x.x     External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x     External: 66.66.666.54(all)

I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?

Here is my NAT config:

nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL

[code]....

View 3 Replies View Related

Cisco VPN :: Remote Client Cannot Connect To Local Network Or Site To Site ASA 5510

Jul 21, 2011

I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.

I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.

View 6 Replies View Related

Cisco WAN :: 2911 - Site-to-site IPsec Vpn / Unable To Ping Remote Network

Apr 3, 2013

I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
  
crypto isakmp policy 1
encr 3des
hash md5

[Code].....

View 9 Replies View Related

Cisco Firewall :: ASA 5510 Identity NAT Configuration For Remote Access VPN And Site-to-Site

Mar 9, 2011

I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .

i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
 
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).

View 6 Replies View Related

Cisco VPN :: ASA 5510 - ISP Site To Site Failover With Single Remote Peer Address

Apr 16, 2011

I have a ASA 5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.
 
Secondly request also they need failover over the ISP link.
 
how we immplement the same on ASA 5510.

View 0 Replies View Related

Cisco VPN :: 506 Firewall 6.3(4) PDM 1.0 / Broke Remote VPN After Site To Site VPN Tunnel Created?

May 19, 2011

It's been a long time since I played in Cisco CLI.Using a Cisco 506 Firewall 6.3(4) PDM 1.0?Problem is I created a site to site tunnnel with a vendor and since then our remote VPN does not work. Completely times out so I am sure I broke something in the crypto map or something similar.
 
Tunnel is policy 10 using access-list 101
Remote VPN is Policy 20

Config Below:

: Saved:PIX Version 6.3(4)interface ethernet0 10fullinterface ethernet1 10fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password XLk0qAaMaA6kjvA6 encryptedpasswd VeCrsQbWdIFPwnny encryptedhostname RMS-DR-PIXdomain-name RMS.Localfixup protocol dns maximum-length 512fixup protocol ftp 21fixup protocol h323 h225 1720fixup protocol h323 ras 1718-1719fixup protocol http 80fixup protocol rsh 514fixup protocol rtsp 554fixup protocol sip 5060fixup protocol sip udp 5060fixup protocol skinny 2000fixup protocol smtp 25fixup protocol sqlnet 1521fixup protocol tftp 69namesobject-group network FTP_Clients description FTP Client PCs network-object host 192.168.xxx.xxx network-object host

[code]....

View 4 Replies View Related

Cisco VPN :: ASA 5510 - Remote Subnet Group To Access Other Site-site VPN?

Feb 14, 2011

I have a cisco ASA 5510 at the branch here. It terminates about 8 vpn tunnels and also it supports remote access clients. I just have a quick question. Can my remote sub-net group access the other remote access site-site VPN subnet group. If yes then how should i configure it.

View 6 Replies View Related

Cisco AAA/Identity/Nac :: Configure Radius Authentication Across Site-to-site VPN For ASA 5510-01 For Remote Access?

Jun 28, 2012

I am attempting to configure Radius authentication accross a site-to-site VPN for my ASA 5510-01 for remote access.
 
 ASA5510-1 currently has a live site to site to ASA5510-2.
 
ASA 5510-1 - 10.192.0.253
 
ASA 5510-2 - 172.16.102.1
 
DC - 172.16.102.10
 
ASA5510-01 can ping the DC and vica versa but is unable to authticate when i perform a test. ASA5510-01 can authenticate to a DC on it;s own LAN but not on the remote LAN that DC sits on.
 
I have double checked the 'Server Secret Key' and ports as well as various users which all work locallly. ASA5510-02 authenticates to DC with no problems.

View 3 Replies View Related

Cisco VPN :: ASA 5505 - Users Aren't Able To Reach Remote Network Through Site-to-site Tunnel

May 21, 2011

Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
 
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
 
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24

View 5 Replies View Related

Cisco Wireless :: Configuring 5508 At Remote Site To Tunnel Traffic From WLC At Main Site?

Sep 20, 2012

At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG).  In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG".  None of the SSIDs are "anchored".
 
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs.  This site contains two customers.  One customer is the Main customer with the second customer leasing space.
 
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan).    I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
 
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500.  It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site.  This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
 
For my test, I am starting simple.  I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low).  I have anchored this test WLAN to that controller.  At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site.  I am unable to obtain an IP address from the remote site.  I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?

View 5 Replies View Related

Cisco VPN :: Asa 5520 Vpn Client On Stick Access From Site To Site

Mar 15, 2012

Have asa 5520 ver 8.0(4) I have vpn client access created and working I have l2l vpn created and working with another set of asa The issue at hand VPN client from internet connects and authenticates, this client can access Site A's networks with no problems. However vpn client on Site A ASA can not access Networks through l2l tunnel located at Site B.

View 2 Replies View Related

Cisco Firewall :: To Setup Syslog For Site-To-Site VPN ASA 5520

Sep 20, 2011

Any step by step guide to setup syslog for site to site VPN.(in ASA 5520)Just send me the step to monitor site to site vpn using that in ASA 5520.

View 2 Replies View Related

Cisco Firewall :: 5520 Slow Performance Through Site To Site Vpn

Mar 12, 2012

I'm having slow performance thru a Site to Site VPN. I have an ASA 5520 in each site with the version 8.2(4) in both ASA's. I have a 20Mb internet service in one side and in the other side I have 50Mb. When I transfer a file from the Sita A to Site B I get a transfer rate of 130KB/S.

View 1 Replies View Related

Cisco VPN :: ASA 5520 - Routing Traffic Between Two Site To Site Tunnels

Feb 24, 2013

I am trying to establish routing between two Site to Site vpn tunnels, both of which are terminating on the same outside interface of my Cisco ASA.
 
find attached Network Diagram for the same. All Firewalls used are Cisco ASA 5520.
 
Both VPN tunnels between Point A and Point B, Point B and Point C too are up. I have enabled Same security level intra interface permit command also.
 
How do i enable traffic originating from LAN Subnets behind Point A to reach LAN Subnets behind Point C without having to create a Seperate tunnel between Point A and Point C

View 5 Replies View Related

Cisco VPN :: 5520 IPsec Site-to-Site VPN Multi-session?

Mar 14, 2011

I recently faced an issue at work. Clients want  to make ipsec site-to-site vpn redundant. I have 2-asa-5520 working in a stack. Is it possible to configure site-to-site vpn in a redundant mode, like first peer ip address is x.x.x.x and secondary is y.y.y.y (backup) ?

View 1 Replies View Related

Cisco VPN :: Site-to-site Failover On ASA 5520 / 3945 Routers

Jan 23, 2012

I am building a site to site VPN from our headquarters to a customer. I am using an ASA 5520. The customer is using Cisco 3945 routers. The customer has two VPN termination points. The customer requests that we make one of their termination points the primary VPN connection and make the other termination point the backup in the event that the primary VPN fails. How do I configure this on the ASA? Does the below configuration fulfill this goal?

View 3 Replies View Related

Cisco VPN :: ASA 5520 / Site To Site Failover VPN Connection And Routing?

Apr 8, 2013

We have 3 sites, with a Cisco ASA 5520 at each location.
 
HQ (Headquarters)              internal network: 172.16.110.0/24,
DR (Disaster Recovery)       internal network: 172.16.120.0/24
BO (Branch Office)               internal network: 172.16.150.0/24
 
HQ and DR have a 100Mbps permanent MPLS link between each other.Branch Office has a Site 2 Site VPN connection to HQ. If it fails, it establishes a Site 2 Site VPN connection to DR. This works perfectly.Now the routing issue... There is no route to the BO in the routing table at HQ/DR. The default gateway is used to reach the BO and that works for HQ when the VPN is between HQ/BO. If the VPN fails over to DR/BO, HQ can't reach BO anymore.I need to have some kind of conditional route injection from the ASA where the VPN is established. I was considering a tracked static route, but I was wondering if the S2S VPN itself has a functionality to do so. I thought the Reverse Route Injection was it but it's enabled on our crypto map and doesn't seem to work...

View 4 Replies View Related

Cisco Routers :: RV180 - Site-to-site VPN And Remote User

Dec 6, 2012

We have successfully establish a site-to-site vpn, but we have some difficulties when PPTP users try to access the remote network linked by this tunnel. LAN users can access the remote network without problem, but users who are connected remotly to the lan (PPTP) can't access computer on the remote network. Is there a way to allow PPTP user to access the remote network ? Adding a route ?

View 1 Replies View Related

Cisco VPN :: ASA5505 Blocking Remote Network / Site-to-site Vpn

Jun 28, 2011

I have a site-to-site VPN already established, everything is working as it should.  I'm trying to block the remote network from accessing our network since we only need to access theirs.  I'm sure this is something very easy to implement with an ACL but I'm not sure where this rule needs to go. The VPN is on ASA 5505. 

View 5 Replies View Related

Cisco VPN :: 876 ISR / Traffic From Easy VPN Client To Remote End Of Site-to-site?

Apr 27, 2011

A user with Easy VPN client connects to a 876 ISR (router A). This router also has a site-to-site VPN to another 876 ISR (router B). What I want to achieve is that the user dials in to router A and can access the network on the remote end of the site-to-site tunnel (router B) In diagram:
 
user (192.168.18.x) - Easy VPN - Router A (192.168.16.x) - sitetosite - Router B (192.168.17.x)
 
I have added routes in router B to the 192.168.18.x network with router A as next hop, but I can't reach the other segment.

View 1 Replies View Related

Cisco VPN :: ASA5505 Site-To-Site And Remote Access On Same Device

Jun 3, 2012

I'm attempting to configure an for both site-to-site and remote access VPNs.  The site-to-site is working fine, however when I connect using the Cisco client, after initial connection and password prompt I get a "not connected" status.  The log states that a policy map match could not be found.  I have successfully set the unit up for remote access with no site-to-site and ran into another host of issues when adding the site-to-site to the working remote access config, so I started over setting up site-to-site first.  I've attempted this through ADSM (hate it) - the current configuration is via CLI.  I'm certain I'm just missing a piece or two.

View 2 Replies View Related

Cisco VPN :: ASA 5505 8.2.1 - Site-to-Site VPN NAT - Add Wireless To Remote Location?

Oct 18, 2012

On one of our branch locations ASA, I have a L2L VPN setup we are adding wireless to this remote location, and the AP's will talk back to the controller at HQ. The AP's are on the downstream L3 switch, and they have been placed on the mgmt network. It's definitely not ideal to have these AP's on the mgmt network, but for now that is how it is setup.

From HQ (163.122.x.x) I can ping and reach the ASA (10.200.2.1, and the downstream L3 switch 10.200.2.100, but when I ping one of the AP's, I get timeouts and and the following error on the ASA:%ASA-3-305005: No translation group found for icmp src outside:10.205.216.73 dst mgmt:10.200.2.152 (type 8, code 0)
 
It appears it's a NAT issue on the ASA, but I'm confused on what I need to change. Why can I ping the ASA and the switch from HQ, but not the AP's which reside on the same mgmt network? I don't really need it to NAT, just to pass the connections. I currently only have the following two NAT statements in the configure

[code]...

View 1 Replies View Related

Cisco VPN :: ASA 5510 - Remote Clients To Site To Site Tunnel

Feb 20, 2013

I have a situation where I need to have remote users vpn into my ASA 5510 and then turn around and hit a site to site tunnel.  Now when I am in our office I can hit the site to site vpn fine.  When I am at home and vpn to the asa I can not get to the site to site resources. Do you see where my config is incorrect? result of the command: "show run"
 
ASA Version 9.1(1)
!
hostname xxxxx
domain-name xxxx
enable password xxxxx
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
[ code]....

View 3 Replies View Related

Cisco VPN :: 5520 And 5505 Site-To-Site Tunnel Between Two ASA

Apr 2, 2013

I am using the Site to Site Wizard on an ASA 5520 and ASA 5505 from the ADSM. Both are using 8.4(5). When you create the configurations. Do you have to follow up the wizard configurations with manual ACL's to allow for traffic from each connected subnet to talk to each other? Or are they automatically generated in the configuration file? Have not been to school yet to properly understand how to create the VPN tunnels from the CLI and what to look for.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved