Cisco VPN :: Site To Site VPN IPSEC Tunnel From ASA 5505 To Clavister Firewall
Nov 20, 2012
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
View 1 Replies
ADVERTISEMENT
Nov 13, 2012
I have a 5505 asa code version 8.3(2). Trying to set up a site to site tunnel with someone and he is asking if I can use ike v2. How do I go about setting up the tunnel to use ikev2? Is ikev2 an option with site to site tunnels?
View 5 Replies
View Related
Feb 7, 2011
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies
View Related
Apr 24, 2013
I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers. But now i need to access internet on site B router sitting on site A router. So that if i run traceroute from A site machine then the gateway by which internet passing through shows the ip of site B.
The Architecture of our both site routers :
Site A 10.1.11.0-----Router A 172.18.12.1-----VPN tunnel----Router B 172.18.12.2-----Site B 10.4.11.0
/////Create IKE policy
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
[Code] .....
View 10 Replies
View Related
Dec 1, 2011
How can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel? I'm using an ASA5520 running 8.04.
I have four hosts say: 10.240.1.1-10.240.1.4
They need access to two different networks:
205.100.150.0
140.175.200.0
I woud like to NAT them as something like:
7.5.210.1
7.5.210.2
7.5.210.3
7.5.210.4
View 1 Replies
View Related
Feb 17, 2013
We have configured a site to site tunnel from our ASA to another organizations Cisco 3030. It appears to have just one way initiation. We can do a ping to a device on the remote site and it will ping just fine. however, when the tunnel needs to be initiated from the remote site, it will not work until we have initiated the tunnel and then everything works.
I continue to see Error processing payload: Payload ID: 1 errors on the ASDM logs.It appears that all the configuration is in place because we can in fact establish the IPSec tunnel unidirectional. And once established, traffic can flow bidirectional.
View 1 Replies
View Related
Nov 28, 2012
I have a situation where the site-to-site tunnel is already established using PPTP IPSec VPN with non Cisco Gateways terminating the link on each end. These non Cisco Gateways do not support L2TP tunneling, and there is no plan to change them.Beyond the Gateways on both ends, we have a Cisco 4500 series switch. We need to forward the 802.1q tagged VLANs between the two sites. Is it possible to use 802.1Q tunneling in this case, going via a PPTP tunnel ?
Cisco's setup uses dot1q-tunnel over a L2protocol-tunnel to preserve the original client VLAN tagging, so does this mean that the only option we have is to setup a L2TP tunnel at the Cisco device endpoints, and have that tunnel go through the existing PPTP tunnel (established between the 2 non Cisco VPN Gateways) ?
View 1 Replies
View Related
Nov 1, 2011
I am having issues getting my ASA 5540 at site A, to pass TFTP and SYSLOG from itself across the IPSEC tunnel to our SYSMON servers (Syslog and TFTP) that live at site B. I have followed the suggestions of other threads and I am still not getting anywhere. Here is a quick topology diagram.
View 6 Replies
View Related
Sep 20, 2011
Can i know cisco 2800 router can support how many site-to-site ipsec tunnel without vpn module?
View 2 Replies
View Related
Aug 10, 2011
I cannot get it to work : if interesting traffic comes ffrom the IPSO side, the box would not even try to set up the tunnel. and If it comes fomr the ASA side, the box attempts to do so but it with this strange message : AM_WAIT_MSG2
View 3 Replies
View Related
Dec 5, 2012
I am setting up a IPSEC VPN tunnel between a Cisco 2921 and ASA 550x. [code]
View 6 Replies
View Related
May 9, 2012
I want a site to site vpn ipsec tunnel there wants to use two Cisco 880 routers that are connected to a modem / router is this possible?
View 12 Replies
View Related
Aug 18, 2011
I have a asa and Cisco 2811, needs to build a site-to-site ip sec tunnel between them. Due to a requirement need to encrypt inside traffic, i need to apply on the inside interfaces on both devices to build the tunnel.
I don't see a problem but just want to check if it would work on terminating on Inside interfaces on both ip sec peers.
View 1 Replies
View Related
Apr 30, 2012
Need to know the step by step procedure for monitoring site-to-site VPN tunnel (up/down) using SNMP on Cisco ASA 5505.
View 1 Replies
View Related
Aug 8, 2011
im drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
View 7 Replies
View Related
May 21, 2011
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24
View 5 Replies
View Related
Dec 27, 2012
Last week, I was able to establish a site-to-site VPN tunnel between an ASA 5505 and Cisco C881 router just fine. The tunnel was up and and running for a number of days but today the tunnel is no longer up. I was wondering how, if there are any commands to re-establish or re-initiate the tunnel.
View 3 Replies
View Related
Nov 14, 2012
i have a client who needs to establish a VPN tunnel from his satellite office (Site A) to his corporate office (Site Z). His satellite office will have a single PC sitting behind the ASA. In addition, he needs to be able to VPN from his home (Site H) to Site A to access his PC.The first question I have is about the ASA 5505 and the various licensing options. I want to ensure that an ASA5505-BUN-K9 will be able to establish the site-to-site tunnel as well as allow him to use either the IPsec or SSL VPN client to connect from Site H to Site A. Secondly, I would like to verify that no special routing or configuration would need to take place in order to allow traffic not destined for Site Z (i.e., general web browsing or other traffic to any resource that is not part of the Site Z network) to go out his outside interface without specifically traversing the VPN tunnel (split tunneling?)Finally, if the client were to establish a VPN session from Site H to Site A, would that allow for him to connect directly into resources at Site Z without any special firewall security rules? Since the VPN session would come in on the outside interface, and the tunnel back to Site Z goes out on the same interface, would this constitute a split horizon scenario that would call for a more complex config, or will the ASA handle that automatically without issue?
View 1 Replies
View Related
Dec 17, 2012
I am using a Cisco ASA 5505 Here is a description of my topology.
Headquarters = 192.168.201.0
Client X = 172.16.0.0
Datacenter = 10.12.0.0
Site to Site Tunnels:
Headquarters ---> Datacenter
Datacenter ---> Client X
I want to ability for computers in the Headquarters subnet to access the Client X subnet.I have tried setting up a static route to push all traffic destin for 172.16.0.0 to the datacenter, but was unsuccessful. how I can route all 172.16.0.0 through the tunnel.I have tried ading a static route on my ASA but without success.
View 3 Replies
View Related
Apr 3, 2013
I do have a 5505 up and running, and passing data... url...Now I am trying to get a IPSEC VPN tunnel working.I actually have it up (IKE phase 1 & 2 both passed), but it is not sending/receiving data through the tunnel.
The networks concerned: name 10.0.0.0 Eventual (HQ Site behind Firewall)name 1.1.1.0 CFS (Public Network Gateway for Palo Alto Firewall - Firewall IP: 1.1.1.1)name 2.2.2.0 T1 (Remote site - Outside interface of 5505: 2.2.2.2)name 10.209.0.0 Local (Remote Network - internal interface of 5505: 10.20 9. 0.3) On a ping to the HQ network from behind the ASA, I get port map translation creation failed for icmp src inside:10.209.0.9 dst inside:10.0.0.33 (type 8, code 0)
I am suspecting that there is a NAT error and/or a lack of a static route for the rest of the 10.0.0.0 traffic, and that I may have to exempt/route the traffic for the HQ network (10.0.0.0), but I haven't been able to get the correct entries to make it work. [code]
View 22 Replies
View Related
Mar 30, 2013
I'm currently trying to configure a Site to Site tunnel between an IOS Router and an ASA 5505 running 9.1
When the private subnet of the IOS Router was 10.0.0.0/24 and the private subnet of the ASA was 172.16.1.0/24, it connected fine.
I'm now trying to set it up where both private networks are 10.0.0.0/24, and created network objects, edited the ACL for interesting traffic, and created the twice NAT translation rule, but the tunnels aren't coming up.
There is the IOS Router(R1) and the ASA(F2). In between them is one Internet posing router that is just set up to allow both sides to reach their WAN addresses.
R1 and F2 have private network (10.0.0.0/24) and need to communicate. Twice NAT can be done all on the ASA to allow this, but I must be doing something wrong. The way I understand it, is that the R1 should see the traffic coming from 10.51.0.0/24 and sending to that traffic. The ASA will take that traffic, and the inside network should see it come inbound as 10.50.0.0/24. So the F2 private network communicates with 10.50.0.0/24 and R1 private network sends traffic to 10.51.0.0/24.
I turned on "Debug crypto ipsec" and "debug crypto isakmp" but no output is showing up or giving any hint that it is trying to establish anything.
R1#show run
version 12.4
hostname R1
crypto isakmp policy 50encr 3desauthentication pre-sharegroup 2crypto isakmp key cisco address 10.2.0.254
[Code]......
View 3 Replies
View Related
Oct 28, 2012
I have a very basic lab site to site vpn setup where I have a ASA 5505 running v7.2(4) on one side and a cisco 2811 on the other side.
What's my issue?
I can't seem to ping from cisco router to the 'inside' network of ASA (see config below) and can't seem to ping from ASA packets leaving the 'inside' interface to cisco router even w/ an ICMP ACL permit outside in. However I'm able to ping within ASA inside network & ping cisco 2811 side w/ packets leaving ASA 'outside' interface just fine.
example:
-------
ciscoasa# ping inside 10.20.20.1 (to cisco loopback1 from ASA inside)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.20.20.1, timeout is 2 seconds:
[Code].....
View 6 Replies
View Related
Apr 2, 2013
I am using the Site to Site Wizard on an ASA 5520 and ASA 5505 from the ADSM. Both are using 8.4(5). When you create the configurations. Do you have to follow up the wizard configurations with manual ACL's to allow for traffic from each connected subnet to talk to each other? Or are they automatically generated in the configuration file? Have not been to school yet to properly understand how to create the VPN tunnels from the CLI and what to look for.
View 2 Replies
View Related
Dec 6, 2012
I am running site to site VPN from site B to site a.On siteB. I used following DNS in site B DHCP from 5505 ASA.dhcpd dns 192.168.1.1 202.66.192.68..When the site to site tunnel is working. It is normal DNS requests from site B to site A DNS. however, if the site to site tunnel is disconnected, site B not able to request site A DNS and do not jump to second DNS 202.66.192.68. I want siteB can use secondary DNS: 202.66.192.68 when tunnel is not connected.
View 2 Replies
View Related
Dec 12, 2012
I am using 5 Cisco 5505 ASA builed site to site VPN. site B,C,D,E all site to site VPN to site A with only IKEv2 IPSEC configurartion.
Reading from Site A ASDM. Monitoring VPN always can read all four site are connected. But, I found that Site D and E the login time during reset time to time with few hours.
1) I would like to know the login time during reset is normal or not?
2) any setup or configuration can fine tune the site to site VPN. Make VPN tunnel more stable?
3) any menthod can monitor site to site VPN is health or not?
View 2 Replies
View Related
Feb 4, 2013
I have ran into this problem in the past but clearly I usually change one of the remote host sub net ranges to something other than main site. Now I am in a situation that I just have to configure it this way. I just need some insight before implementation.
Inside (10.10.10.x/24) ASA5505 outside (97.65.x.x) ßà (97.664.x.x) outside ASA5505 (10.10.10.x/24)
Trying to create a site to site tunnel between each location with same sub net. I have found a lot of information about setting up this configuration with 8.3 and later but nothing for the image 8.4 and image 9.1(1) as everyone knows the ACL's and NAT statements are written differently now.
View 5 Replies
View Related
Sep 30, 2012
I've got a Cisco 5520, to which is a Cisco 5505 is connected via a Site to Site tunnel.The tunnel works just dandy, with traffic happily being passed to and from my Inside interface.
The issue comes with users connected to the 5505 access our DMZ, it simply refuses to work. I've read many posts about the changes made in 8.3 (which I'm running on the 5520) when it comes to NAT exemptions which I believe is the issue I'm having but I'm not able to implement any configuration to allow my site to site VPNs to connect to hosts within the DMZ.
An old copy of the configuration below (I tried many things after this point, but this is one of the cleaner copies!), [code]
View 5 Replies
View Related
Sep 29, 2012
I just try to build a Site-to-Site VPN over IPSec between a ASA5505 and a ASA5510. But it don`t want to work. Here are the config`s of the ASA 5505 and ASA5510:
ASA5505:
: Saved
: Written by enable_15 at 20:02:51.175 UTC Wed Apr 7 2010
!
ASA Version 7.2(2)
!
hostname asa5505
enable password 8Ry2YjIyt7RRXU24 encrypted
names
View 22 Replies
View Related
Jun 3, 2012
We have an ASA 5505 in our environment and currently two IPSec L2L VPN tunnels are established. But we are planning to connect using Easy VPN(Network Extension Mode) to another site as Client. Is it possible to configure Easy VPN configurations by keeping the currently active IPSec L2L VPN(Site-to-Site) tunnels?
Following is the warning that we get when tried to configure Easy VPN Client.NOCMEFW1(config)# vpnclient enable
* Remove "nat (inside) 0 S2S-VPN"
* Detach crypto map attached to interface outside
* Remove user-defined tunnel-groups
* Remove manually configured ISA policies
CONFIG CONFLICT: Configuration that would prevent successful Cisco EasyVPN Remote operation has been detected, and is listed above. P
View 6 Replies
View Related
Nov 6, 2011
I am setting up a site to site IPSec VPN between two ASAs.I want to NAT an internal host that my VPN peer's network will be connecting to. So I need to make sure the traffic coming from this internal host is NATted before it enters the VPN tunnel as "interesting traffic"
So let's say remote network 192.168.20.0 /24 is connecting through IPSec VPN tunnel with peers 65.200.1.1 and 198.14.7.10 to host 10.100.1.7 on my network.I want to NAT host 10.100.1.7 to 192.168.100.5 to the remote network connects to the 192 address, not the 10 (I am using a ASA 5505)
View 9 Replies
View Related
Jul 5, 2012
Is there a limit on how many remote networks you can specify on a Site to Site VPN tunnel?
View 1 Replies
View Related
May 1, 2012
We installed an ASA5505 an we configured a vpn l2l to another asa,unfortunately this vpn tunnel sometimes goes down and do not come up again, in order to keep it up we need to have a continuos ping to generate traffic inside the tunnel.,How is possible to keep this vpn tunnel always up?,This is the config,ASA Version 8.4(1).
View 2 Replies
View Related
May 18, 2011
I have a simple question, but want to make sure before I start. I have 3 5505 devices, 1 at corp, and 1 at two site locations. Is it possible to have multiple tunnels on the corp asa? one to site #1 and one to site #2?
My license is Base on all of the ASA's. I already have remote user VPN setup on the devices as well. Will that hurt or hinder anything to add the tunnels?
View 2 Replies
View Related
