Well, I tried using the cisco configuration for ASA 5505 for blocking P2P: url...but this configuration only is usefull with programs like Kazaa, so I try this configuration to block ARES but the problem is that ARES try to make downloads from different ports, ¿How do I block ARES if there are sereveral ports ?
View 1 RepliesI am working on ASA 5505 with Base License that uses 3 VLAN's.
-My VLAN 1 is for used for my home network.
-VLAN 2 is connected to the public Internet and my IP gets assigned by ISP dynamically.
-VLAN 3 is DMZ where I will have few VM's that would need access to and from the Internet.
I am looking to work with following:
1) 172.16.0.2 that sits on DMZ will need to access public Internet over port 80
2) Permit access from the Internet over port 3389 to 172.16.0.2
3) Permit any host on private VLAN (192.168.0.0 network) to access 172.16.0.2 over the port 3389
4) Permit second VM on the DMZ VLAN let say 172.16.0.3 to access public Internet on all ports. Access in to this host is not permitted.
5) For some reason DHCP hosts are NOT getting DNS (8.8.8.8) entry when IP hets assigned or renew. I have a statements below but it is not working.
Also, if ACL rules for VoIP are written correctly. The goal is to permit these ports (SIP related) to access VoIP router. [code]
I'm tring to setup a DMZ for a guest wireless off of a 5505. So this device has a base license. It has vlan1 and vlan 2 for inside and outside.Another vlan is configured to be a failover for the currently active wan connection. It is using the "no forward interface" command.Can I add another vlan as a DMZ if I use the "no forward interface" command? [code]
View 6 Replies View RelatedI have ASA 5505 with base licence. I configured NATing and VPN(site to site). All are working fine.My ASA is base license so i created 2 VLANS, one is inside and outside.Inside i am using 10.91.40.0/24 serie IP addresses.Below are the new requirements that i need to configre:
1. First 30 IP addresses only needs internet directly.( Servers and Management)
2. If remaining IPs likes to use web then traffic needs to forward one proxy server( where he gives user authentiation)
My ASA 5505 base license allows for three VLANs, the third one can only initiate traffic to one other VLAN (as specified by no forward interface vlan <number> on the third VLAN). This doesn't mean it can't "access" the other VLAN, it just can't initiate traffic to it. A lot of people get that wrong.Let's say you've got three VLANs, one is OUTSIDE, two is DMZ, and three is INSIDE. On the second VLAN would I enter the no forward interface as vlan 3, then set the name via the nameif command and everything will work just fine. The DMZ will not be able to initiate traffic to the INSIDE, but will to the outside, and assuming you have your ACLs and NAT set up properly, it will be able to respond to traffic from the INSIDE.
Would that be best practice or would I enter the "no forward" interface as in VLAN 1, thus is being able to respond to traffic from the outside as opposed to the inside.
I had a DMZ set up but since there was an intrusion into my network, I am building it again.
I have a couple of 5505's with base licenses. One of the two has a limited output when running the sho version command, as it has a restricted license. What license I would need to buy in order to bring it up to "normal" base license ?
View 1 Replies View RelatedI have a base 5505 and would like to get AnyConnect working. To do that, would I have to first purchase either an essentials or premium license and then purchase the AnyConnect Mobile license?
View 1 Replies View Relatedbasic step to blocking site on ASA 5505 version 8.2(1) base license using CLI
View 1 Replies View RelatedWe have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.
View 1 Replies View Relatedwe have a cisco ASA5505 with base license and 3 interface configured. Internal 192.168.1.1/24 DMZ 172.16.0.1/24 Outside 20.20.20.20/24 The DMZ is configured to allow the traffic pass to the outside interface only (base license allow only traffic to one interface) in order to let clients on this network to browse internet. On the outside interface there's a nat configuration that let the port 443 to be natted to an in internal server. Is it possible to let the clients in DMZ to access to the internal server on port 443 from the outside interface?
View 3 Replies View Relatedwe have a customer with a ASA 5510 with a CSC module in it. The device tells us the Base license has expired. The new license has been renewed - after - the grace period. The Trendmicro site tells us the Base license is valid until 21 october 2013 but the CSC refuses to acknowledge this. The module is able to fetch updates form the Internet so it does not look like a connection problem to me (it also has a plus license which is also valid till far into 2013 and that one works).Is it possible that the current license key is "dead" and the CSC expects a new license key because the grace period was expired?
View 1 Replies View RelatedI'm new to ASA and bought a used one from ebay but I cannot connect to the ASDM - I get an error in all the browsers.
Cannot communicate securely with peer: no common encryption algorithm(s).
(Error code: ssl_error_no_cypher_overlap)
Having browsed the support forums and Google - it seems I need the 3DES license. I have obtained an activation key from Cisco and applied it to my ASA 5505 however I get a warning about the device is licensed for a higher software level. the license on the ASA is Security plus. When I apply the activation key from Cisco most of the features are disabled.
[Code] ......
We are trying to migrate WCS base license to NCS 1.1 .We have procured the migration license .In the licensing guide , it is mentioned as "L-WCS-NCS1-M-K9 License first, before adding the licenses migrated from your WCS installation"
1)Whether we need to add this migration license in WCS before genrating XML file or
2)Before adding XML file in NCS we need to add this in NCS ..
I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
I've purchased a used ASA 5505 device. Upon reseting and looking at the startup, I see that it is unable to retrieve Activation License and used default. Activation License shows as all zeros.
Is there a way to find whatever Activation License is tied to my device from Cisco without a service contract ? or I have to live with the default ?
I have a Cisco ASA 5505 device with basic (default) license, currently all my reirections, VPN's, VLAN's(3 Vlan's) etc are configured on the same and are working fine.Now i need to upgrade my basic license to "Security Plus" for some additional features, if i upgrade it directley is there any complications in present rules, below is my doubhts
1. if i upgrade, did it change any of my present configurations ?
2. is there any name change or property changes for VLAN's or VPN's
3. did it affect the firewall functions
4. If anything goes wrong, can i restore it in to my old state using my previous dump.
I am planning to setup Clientless Web VPN on our ASA 5505 for secure access to a internal web resource from outside. When I checked the licensing details on the ASA using #sh ver I could notice thar Web VPN peers allowed is only 2 Does this mean that only two clientless simoultaneous connections are possible ?
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
[Code]....
One of our clients has recently purchased upgrade licenses for their cisco asa as follows
L-ASA5505-10-50=
and
L-ASA5505-SEC-PL=
after retrieving the activation key from the cisco website we tried entering the activation key to the asa both via ASDM and telnet when entering the command on telnet the shell becomes unresponsive when entering the command on ASDM we receive a "success" message followed by a request to restart ASDM and save the configuration after a minute or so i get an error screen saying "write mem" the asdm restarts and nothing changes.
We want to upgrade one of our Cisco 5505 with Security Plus license. what is the difference between L-ASA5505-SEC-PL and ASA5505-SEC-PL upgrade licenses?
View 1 Replies View RelatedI recently purchased a used Cisco ASA 5505 and I accidentally (and very stupidly) erased the flash without backing up my license.I have generated a demo licence from the Cisco licencing site, so I have basic functionality. However, the email that I received informed me that there is a higher licence already stored for my device.My question is, is there a way to get that licence back if I can provide the serial number / any other identification to prove I now own the ASA?
View 2 Replies View RelatedI have 5505 license with default 10 user license, want to increment the remote vpn user to 50 user license;will it be on yearly basis.Another question, can we purchase security plus license for configuring the failover config ,as well support the 50 user license on the same..
View 3 Replies View RelatedHow to install IP base liecense and Unified communication liecense in 2921 router?
View 1 Replies View RelatedWe recently upgraded a ASA 5505 with the security plus license to allow us to add a second subnet, but are having a few problems configuring the second subnet. The original subnet we have configured 10.1.1.0 is able to access the internet without any problems. However the new subnet 10.1.5.0 is unable to access the internet and when we ran a trace packet the nat config nat (inside) 1 0.0.0.0 0.0.0.0 is showing as the rule that drops the packet.
Additionally we have not been able to get the 2 subnets to talk to each other even though same-security-traffic permit inter-interface is configured. How to configure the subnet 10.1.5.0 to access the internet or to get the subnets to communicate. Below is a streamlined version of our current config.
!interface Vlan1nameif insidesecurity-level 100ip address 10.1.1.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 66.66.66.66 255.255.255.240 ospf cost 10!interface Vlan13nameif corporatesecurity-level 100ip
[Code].....
I am buying ASA 5505 with security license. It says it can support 20 vlans does it support 20 vlans by allowing to create subinterfaces? As it has 8 physical ports only?
View 3 Replies View RelatedI'm trying to activate the DMZ interface on a restricted license ASA 5505 but I get an error when I try to ADD the interface. The message says "With the current license device will only supports 2 fully functional interfaces. Third interface can be added,but the traffic from this interface to another interface need to be blocked. Please make appropriate selection in advanced tab." I gather that I have to define the limitation myself? The problem is that I can't access the advanced tab because of the error. Can I do something via CLI to get through? I'm using ASA 8.2 and ASDM 6.2.
View 4 Replies View RelatedI am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies View RelatedWould like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies View RelatedI am bringing up a 3750x and a 2911 to replace a 3745 router with switchport module. I was plannng on moving all the VLAN interfaces off the 3745 onto the 3750x and turning up EIGRP. I discoved the 3750 has the LAN Base license, so I can't run eigrp off of it. My question or worry now is, will the LAN base license prevent the switch from doing interface VLAN routing between the different VLAN's configured on it or will I have keep all the VLAN interfaces on the new router and just have a router on a stick setup?
View 4 Replies View RelatedI am using ASA5505 and I would like to block certain websites such as facebook.com on some users only
View 3 Replies View RelatedWe have a client that is running a PC on a internet over satellite. To avoid any unessecery traffic over the satellite link (data traffic is quite expensive), we've suggested to use a 5505, as we had one handy already.
So basically what we wanted was to block everything outgoing and everything ingoing, except for example port 22 (ssh).
But I'm struggling a bit, since this is my first cisco router to be configured.
My interfaces are as follows.
Outside - DHCP
Inside (port 1) - 192.168.1.1
I'm only running ipv4.
in ASDM I made a static NAT rule for port 22, being forwarded to 192.168.1.5 (the computer)
in Access rules I made under outside (incomming rules) source=any destination=outside service=ssh action=permit
But when I try to add further rules to block everything else, it takes the SSH on port 22 with it. How should I do this the easiest way?
the hardware setup is pretty straight forward.
sat-terminal(with IP 192.168.0.1 running DHCP) -> 5505 (outside IP=DHCP - inside IP=192.168.1.1) -> computer (IP=192.168.1.5)
At the end of the day I simply need to upgrade the license on my ASA 5505 v7.2.4 (upgrade will come later as part of a larger project) to allow for >10 Inside Hosts. From what I've read there seems to be a 50 license upgrade out there. Can this be purchased directly? From whom? Will it only affect the Inside Hosts number and not affect any other licenses, configurations, etc. Just being overly cautious since this is way outside of my normal realm. Below is the current activation-key information....
Result of the command: "show activation-key"
Serial Number: xxxxxxxxxxxxxx
Running Activation Key: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : 10
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
The flash activation key is the SAME as the running key.
if it is possible to block a website or ip address from an ASA 5505? if it is possible, can you give me an example of the commands to get it done?
View 2 Replies View RelatedI was asked to block pings from the internet to the outside interface of our ASA-5505 firewall. I found a post that said to enter "icmp deny any outside", however that does not do it.
I created an ACL to try and do the trick, also to no avail:
access-list outside_in extended permit icmp any any echo-reply
access-list outside_in in interface outside
access-group outside_in in interface outside