I am buying ASA 5505 with security license. It says it can support 20 vlans does it support 20 vlans by allowing to create subinterfaces? As it has 8 physical ports only?
View 3 Replies
We want to upgrade one of our Cisco 5505 with Security Plus license. what is the difference between L-ASA5505-SEC-PL and ASA5505-SEC-PL upgrade licenses?
View 1 Replies View RelatedWe recently upgraded a ASA 5505 with the security plus license to allow us to add a second subnet, but are having a few problems configuring the second subnet. The original subnet we have configured 10.1.1.0 is able to access the internet without any problems. However the new subnet 10.1.5.0 is unable to access the internet and when we ran a trace packet the nat config nat (inside) 1 0.0.0.0 0.0.0.0 is showing as the rule that drops the packet.
Additionally we have not been able to get the 2 subnets to talk to each other even though same-security-traffic permit inter-interface is configured. How to configure the subnet 10.1.5.0 to access the internet or to get the subnets to communicate. Below is a streamlined version of our current config.
!interface Vlan1nameif insidesecurity-level 100ip address 10.1.1.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 66.66.66.66 255.255.255.240 ospf cost 10!interface Vlan13nameif corporatesecurity-level 100ip
[Code].....
What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View Relatedi have asa 5505 adaptive security plus. and i have only 3 vlans . outside , inside , DMZ restricted.so it's working fine but i want to connect to my inside another private network, or do i need to buy License.and how i can activate the license key.
View 4 Replies View RelatedDo I need the security plus license to do HA with two 5520's?I was told by our purchasing department that the 5520 was supposed to be able to do HA out of the box, but when I look I see only the VPN + license. Does that mean I can download the security plus license? Or do I even need it on the 5520.
View 2 Replies View RelatedI have Cisco ASA5505 8.2(5) connected with Cisco 5520 8.2(1) via IPSEC tunnel, I was able to SSH from the inside 5520 to inside IP of the asa5505. but I after I upgrade the license to security plus at 5505 I lost the SSH and ASDM to inside IP of 5505 from the inside network of the 5520. however I still can use SSH and ASDM on outside IP of 5505.
I did a lot of testing to make it work but I couldn't I added SSH 0.0.0.0/0 inside and outside also I added acl on both interfaces. when I did a trace on the outside interface from the private network of 5520 to 5505 inside IP I got IPSEC spoofed by the way that trace only works with security plus because I try to test on all my other firewalls 8.2(5) it shows nothing and all my firewalls can accessed from the private network 5520 except the one with the security plus!
I'm new to ASA and bought a used one from ebay but I cannot connect to the ASDM - I get an error in all the browsers.
Cannot communicate securely with peer: no common encryption algorithm(s).
(Error code: ssl_error_no_cypher_overlap)
Having browsed the support forums and Google - it seems I need the 3DES license. I have obtained an activation key from Cisco and applied it to my ASA 5505 however I get a warning about the device is licensed for a higher software level. the license on the ASA is Security plus. When I apply the activation key from Cisco most of the features are disabled.
[Code] ......
I need your support for upgrading the Security context license on 5550, at present we have 5 Security context license installed in ASA but we want it to increased till 10 conctexts. I want to understand if we need to get addtional 5 Security context license or 10.
View 5 Replies View RelatedI have ASA 5510. Is there any difference between CSC-10-PLUS license and Security Plus License...
View 3 Replies View RelatedI've purchased a used ASA 5505 device. Upon reseting and looking at the startup, I see that it is unable to retrieve Activation License and used default. Activation License shows as all zeros.
Is there a way to find whatever Activation License is tied to my device from Cisco without a service contract ? or I have to live with the default ?
I have a Cisco ASA 5505 device with basic (default) license, currently all my reirections, VPN's, VLAN's(3 Vlan's) etc are configured on the same and are working fine.Now i need to upgrade my basic license to "Security Plus" for some additional features, if i upgrade it directley is there any complications in present rules, below is my doubhts
1. if i upgrade, did it change any of my present configurations ?
2. is there any name change or property changes for VLAN's or VPN's
3. did it affect the firewall functions
4. If anything goes wrong, can i restore it in to my old state using my previous dump.
I am planning to setup Clientless Web VPN on our ASA 5505 for secure access to a internal web resource from outside. When I checked the licensing details on the ASA using #sh ver I could notice thar Web VPN peers allowed is only 2 Does this mean that only two clientless simoultaneous connections are possible ?
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
[Code]....
One of our clients has recently purchased upgrade licenses for their cisco asa as follows
L-ASA5505-10-50=
and
L-ASA5505-SEC-PL=
after retrieving the activation key from the cisco website we tried entering the activation key to the asa both via ASDM and telnet when entering the command on telnet the shell becomes unresponsive when entering the command on ASDM we receive a "success" message followed by a request to restart ASDM and save the configuration after a minute or so i get an error screen saying "write mem" the asdm restarts and nothing changes.
A simple question - I have ASA 5520s and was wondering what license is required to create multiple (more than default 2) security contexts.
The ASA already have ASA 5520 VPN Plus license.
Software Version 8.4(1)
I have a ASA 5510 with Security Plus License and when I looked at the devices a few days ago I had 2 contexts, however after configuring the Mgm port as a regular port the contexts show 0, why? I can not find any post on the internet where this issue has happen: here is the output from show ver:
Cisco Adaptive Security Appliance Software Version 7.0(8)
Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"
[Code]......
I am working on ASA 5505 with Base License that uses 3 VLAN's.
-My VLAN 1 is for used for my home network.
-VLAN 2 is connected to the public Internet and my IP gets assigned by ISP dynamically.
-VLAN 3 is DMZ where I will have few VM's that would need access to and from the Internet.
I am looking to work with following:
1) 172.16.0.2 that sits on DMZ will need to access public Internet over port 80
2) Permit access from the Internet over port 3389 to 172.16.0.2
3) Permit any host on private VLAN (192.168.0.0 network) to access 172.16.0.2 over the port 3389
4) Permit second VM on the DMZ VLAN let say 172.16.0.3 to access public Internet on all ports. Access in to this host is not permitted.
5) For some reason DHCP hosts are NOT getting DNS (8.8.8.8) entry when IP hets assigned or renew. I have a statements below but it is not working.
Also, if ACL rules for VoIP are written correctly. The goal is to permit these ports (SIP related) to access VoIP router. [code]
I'm tring to setup a DMZ for a guest wireless off of a 5505. So this device has a base license. It has vlan1 and vlan 2 for inside and outside.Another vlan is configured to be a failover for the currently active wan connection. It is using the "no forward interface" command.Can I add another vlan as a DMZ if I use the "no forward interface" command? [code]
View 6 Replies View RelatedI have ASA 5505 with base licence. I configured NATing and VPN(site to site). All are working fine.My ASA is base license so i created 2 VLANS, one is inside and outside.Inside i am using 10.91.40.0/24 serie IP addresses.Below are the new requirements that i need to configre:
1. First 30 IP addresses only needs internet directly.( Servers and Management)
2. If remaining IPs likes to use web then traffic needs to forward one proxy server( where he gives user authentiation)
I recently purchased a used Cisco ASA 5505 and I accidentally (and very stupidly) erased the flash without backing up my license.I have generated a demo licence from the Cisco licencing site, so I have basic functionality. However, the email that I received informed me that there is a higher licence already stored for my device.My question is, is there a way to get that licence back if I can provide the serial number / any other identification to prove I now own the ASA?
View 2 Replies View RelatedMy ASA 5505 base license allows for three VLANs, the third one can only initiate traffic to one other VLAN (as specified by no forward interface vlan <number> on the third VLAN). This doesn't mean it can't "access" the other VLAN, it just can't initiate traffic to it. A lot of people get that wrong.Let's say you've got three VLANs, one is OUTSIDE, two is DMZ, and three is INSIDE. On the second VLAN would I enter the no forward interface as vlan 3, then set the name via the nameif command and everything will work just fine. The DMZ will not be able to initiate traffic to the INSIDE, but will to the outside, and assuming you have your ACLs and NAT set up properly, it will be able to respond to traffic from the INSIDE.
Would that be best practice or would I enter the "no forward" interface as in VLAN 1, thus is being able to respond to traffic from the outside as opposed to the inside.
I had a DMZ set up but since there was an intrusion into my network, I am building it again.
I have 5505 license with default 10 user license, want to increment the remote vpn user to 50 user license;will it be on yearly basis.Another question, can we purchase security plus license for configuring the failover config ,as well support the 50 user license on the same..
View 3 Replies View RelatedIs it possivble to have 10 security licenses, license to a Cisco 5510 and have them transfeered to a Cisco5520?
View 1 Replies View RelatedI have a couple of 5505's with base licenses. One of the two has a limited output when running the sho version command, as it has a restricted license. What license I would need to buy in order to bring it up to "normal" base license ?
View 1 Replies View RelatedWell, I tried using the cisco configuration for ASA 5505 for blocking P2P: url...but this configuration only is usefull with programs like Kazaa, so I try this configuration to block ARES but the problem is that ARES try to make downloads from different ports, ¿How do I block ARES if there are sereveral ports ?
View 1 Replies View RelatedI'm trying to activate the DMZ interface on a restricted license ASA 5505 but I get an error when I try to ADD the interface. The message says "With the current license device will only supports 2 fully functional interfaces. Third interface can be added,but the traffic from this interface to another interface need to be blocked. Please make appropriate selection in advanced tab." I gather that I have to define the limitation myself? The problem is that I can't access the advanced tab because of the error. Can I do something via CLI to get through? I'm using ASA 8.2 and ASDM 6.2.
View 4 Replies View RelatedI have a base 5505 and would like to get AnyConnect working. To do that, would I have to first purchase either an essentials or premium license and then purchase the AnyConnect Mobile license?
View 1 Replies View Related i am trying to get my ASA 5505 with 2 internal VLANs (voice and data) and external internet VLAN to run in router as a stick, and route between VLANS.
I cant get it working though:
[code]...
I have an ASA 5505 and I have the three regular vlans, outside, inside and dmz. The best would be only have outside and inside and skip dmz, but without explenation there is not possible to have more then two clients in whats now dmz because of a mac filter on third party device.
So as security is concerned dmz and inside is equal, one to one and there should be full access between them. I ran the wizard and said that the only way traffic not should be possible to flow is from dmz to outside.
In the NAT rules the onle rule is
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
But traffic from one way or the other dmz to inside, og inside to dmz it says in log
3Dec 06 201215:38:39305006172.17.6.1053portmap translation creation failed for udp src inside:192.168.6.102/49358 dst dmz:172.17.6.10/53 From documentation I have an image with network drawing from documentation. What do I have to do allow traffic btween inside and dmz, both ways.
I have a 5505 with Base license running ASA software v8.4(2) that has been working happily for a while with an inside and an outside VLAN.
The outside has a single statically configured public IP, and I have a number of static NAT rules to expose a few internal servers as well as Dynamic-NAT for all devices on inside to gain access to the Internet... the main bits of the config are below:
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
[code]....
I now have a requirement to add a "dmz" VLAN for guests to have access to the Internet using a dedicated wireless AP, but not to any of the inside resources. As the ASA has a base license I have configured "no forward interface" to the inside vlan, which suits the purpose fine
interface Vlan12
description Used only for guests access to the Internet - no access to the corporate resources
no forward interface Vlan1
nameif guests
security-level 20
ip address 192.168.2.1 255.255.255.0
My problem is that when I try to add NATing from the dmz to the outside I get a:
ERROR: Address a.b.c.d overlaps with outside interface address.
ERROR: NAT Policy is not downloaded
with either:
object network guests_subnet
subnet 192.168.2.0 255.255.255.0
nat (guests,outside) dynamic interface
[code]....
Having had a look at the ASA Configuration guides, all the examples I can see with several "internal" VLAN's being NAT'ed use one external IP per VLAN - is this a feature/restriction of the ASA software? Are there any workarounds? Or is the overlap in the error message really about the current NATing to the inside VLAN which is done on the "any" 0.0.0.0 subnet - would the following then work:
object network obj_any
subnet 192.168.1.0 255.255.255.0
nat (inside,outside) dynamic a.b.c.d
object network guests_subnet
subnet 192.168.2.0 255.255.255.0
nat (guests,outside) dynamic a.b.c.d
so I look up ASA5505 licensing and for VLAN support see: 3 (no trunking support)/20 (with trunking support)*
I need 3 VLANs...inside, outside, and DMZ..but when it is creating the third (DMZ) it says I am only allowed to have 2 VLANs and can only create the third if its set to not forward traffic. ?
I have to upgrade to an ASA 5510 CSC, and the new license is generated, the file you sent me licensing, only seen this:Activation Code not required for this renewal. Please go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date (BASE: 09/04/2014, PLUS: 09/04/2014).This means that what I have not make any upgrades or license charge in the ASA? Does the automatic update is made?
View 1 Replies View RelatedAt the end of the day I simply need to upgrade the license on my ASA 5505 v7.2.4 (upgrade will come later as part of a larger project) to allow for >10 Inside Hosts. From what I've read there seems to be a 50 license upgrade out there. Can this be purchased directly? From whom? Will it only affect the Inside Hosts number and not affect any other licenses, configurations, etc. Just being overly cautious since this is way outside of my normal realm. Below is the current activation-key information....
Result of the command: "show activation-key"
Serial Number: xxxxxxxxxxxxxx
Running Activation Key: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : 10
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
The flash activation key is the SAME as the running key.
