Do I need the security plus license to do HA with two 5520's?I was told by our purchasing department that the 5520 was supposed to be able to do HA out of the box, but when I look I see only the VPN + license. Does that mean I can download the security plus license? Or do I even need it on the 5520.
View 2 RepliesWhat's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedCan i buy a plus license for asa 5520??
View 2 Replies View RelatedI have got ASA 5520. I am planning to install Cisco ASA AIP SSM-20 and Cisco ASA Content Security and Control (CSC) Security Services Module on ASA 5520.. However I am also thinking of adding AIP only as I can do the function of content filtering with proxy server. Relating this issue I would like to ask -
1. What would be the benefit of adding CSC ?
2. Do I have to pay the license cost every year for both of these SSM? What would be the cost ?
3. Upto how many SSM can I add into ASA 55020 ?
I have a running ASA5520 in my network and recently we plan to add a failover pair as a standby unit for the running asa. Both of the ASA have the same specs and software. the only thing that the soon to be secondary ASA does not have is the AnyConnect Essential license. is it still possible for the unit to be the standby unit?
below is the license capture from both of the unit.
Running ASA:
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
[Code].....
According to the link here:[URL]Starting with Version 8.3(1), it no longer needs to install identical licenses. Typically, we only buy a license only for the primary unit; for Active/Standby failover, the secondary unit inherits the primary license when it becomes active.So I wanna know if there's some additional configuration to synchronize the licenses such as SSL VPN or Context between the primary one and the second one? Or they can just synchronize by default as soon as I finish the failover configuration and when the primary one gets down, the second one will take over the role including licenses automatically?
View 4 Replies View RelatedWe apply a new anyconnect mobile license to our primary asa 5520 and the failover feature went into an off state. WE have now applied a second purchased anyconnect mobile to our secondary asa but the failover is still inactive/off.
bcoh1fw50# sh failover state
State Last Failure Reason Date/Time
This host - Primary
Disabled Ifc Failure 14:43:21 EST Jan 30 2013
[Code].....
I have Cisco ASA5505 8.2(5) connected with Cisco 5520 8.2(1) via IPSEC tunnel, I was able to SSH from the inside 5520 to inside IP of the asa5505. but I after I upgrade the license to security plus at 5505 I lost the SSH and ASDM to inside IP of 5505 from the inside network of the 5520. however I still can use SSH and ASDM on outside IP of 5505.
I did a lot of testing to make it work but I couldn't I added SSH 0.0.0.0/0 inside and outside also I added acl on both interfaces. when I did a trace on the outside interface from the private network of 5520 to 5505 inside IP I got IPSEC spoofed by the way that trace only works with security plus because I try to test on all my other firewalls 8.2(5) it shows nothing and all my firewalls can accessed from the private network 5520 except the one with the security plus!
We want to upgrade one of our Cisco 5505 with Security Plus license. what is the difference between L-ASA5505-SEC-PL and ASA5505-SEC-PL upgrade licenses?
View 1 Replies View RelatedI need your support for upgrading the Security context license on 5550, at present we have 5 Security context license installed in ASA but we want it to increased till 10 conctexts. I want to understand if we need to get addtional 5 Security context license or 10.
View 5 Replies View RelatedI have ASA 5510. Is there any difference between CSC-10-PLUS license and Security Plus License...
View 3 Replies View RelatedA simple question - I have ASA 5520s and was wondering what license is required to create multiple (more than default 2) security contexts.
The ASA already have ASA 5520 VPN Plus license.
Software Version 8.4(1)
We recently upgraded a ASA 5505 with the security plus license to allow us to add a second subnet, but are having a few problems configuring the second subnet. The original subnet we have configured 10.1.1.0 is able to access the internet without any problems. However the new subnet 10.1.5.0 is unable to access the internet and when we ran a trace packet the nat config nat (inside) 1 0.0.0.0 0.0.0.0 is showing as the rule that drops the packet.
Additionally we have not been able to get the 2 subnets to talk to each other even though same-security-traffic permit inter-interface is configured. How to configure the subnet 10.1.5.0 to access the internet or to get the subnets to communicate. Below is a streamlined version of our current config.
!interface Vlan1nameif insidesecurity-level 100ip address 10.1.1.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 66.66.66.66 255.255.255.240 ospf cost 10!interface Vlan13nameif corporatesecurity-level 100ip
[Code].....
I am buying ASA 5505 with security license. It says it can support 20 vlans does it support 20 vlans by allowing to create subinterfaces? As it has 8 physical ports only?
View 3 Replies View RelatedI have a ASA 5510 with Security Plus License and when I looked at the devices a few days ago I had 2 contexts, however after configuring the Mgm port as a regular port the contexts show 0, why? I can not find any post on the internet where this issue has happen: here is the output from show ver:
Cisco Adaptive Security Appliance Software Version 7.0(8)
Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"
[Code]......
Is it possivble to have 10 security licenses, license to a Cisco 5510 and have them transfeered to a Cisco5520?
View 1 Replies View RelatedI have to upgrade to an ASA 5510 CSC, and the new license is generated, the file you sent me licensing, only seen this:Activation Code not required for this renewal. Please go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date (BASE: 09/04/2014, PLUS: 09/04/2014).This means that what I have not make any upgrades or license charge in the ASA? Does the automatic update is made?
View 1 Replies View RelatedI have an ASA 5520 running 8.0(3) with two Subinterfaces configured like this:
=================================
interface GigabitEthernet0/1
nameif inside
security-level 100
no ip address
!
interface GigabitEthernet0/1.72
description VLAN 72
[code]....
(notice that they have the same security-level)I need to control the traffic between them with ACLs so I in ASDM unchecked "enable traffic between two or more interfaces with same security level" and "enable traffic between two or more hosts connected to the same interface"Now I cannot ping from one Vlan to the other, as expected,,, but I tried many different ACLs and I cannot ping or telnet to the other side from either one.
I have a DMZ (50) from where I need to allow some protocols to inside zone (level 0). I am doing that with ACL, but after having done that the implicit security level rule to lower level (outsite level 0) is not working anymore, I guess by the implicity deny after the acl. I'd need allow traffic to the outside zone from DMZ, as well as the inspect traffic from the inside one. Is there anyway to have both ACL and Security levels?
If not, what do I need to do to just allow some protocols going to higher level and leave the higher-to-lower traffic inspected allowed, same schema as we have with security levels.
On a Cisco ASA 5520. I have 2 interfaces that are the same security level. I need hosts on 1 of these interfaces to be able to get to a specific IP and port on the other but I DON'T want to blanket enable 'same-security-traffic permit inter-interface" I have added an ACL inbound on the interface allowing the desired traffic and inbound on the other for return traffic and it simply doesn't work.
interface GigabitEthernet0/3.175
vlan 175
nameif Test175
security-level 30
ip address 172.30.175.1 255.255.255.0
[code]....
I have issue with traffic passing between same security level interfaces. I want to control traffic between same security level interfaces with ACL. Even no restriction, traffic does not go through. [code]
I tried to access server from THREE network to web server at FOUR network I have no response. In sh xlate output it shows "PAT Global 10.124.104.254 (28889) Local 10.124.103.1(2922) " I am not sure what else should I do. I add both same-security-level commands and it is the same.
Ive got a virtualised firewall running 3 security contexts in routed mode. What am experiencing is that i cannot connect to an OUTSIDE host through the security contexts. From the firewall itself i cannot ping the directly attached host on the OUTSIDE interface but i can ping the directly attached host on the INSIDE interface. When i reload the firewall box, the first ping to the OUTSIDE host would be successful but subsequent pings fail and thus total connectivity is lost.
I even tried upgrading to ASA version 8.4(1) but still the same.
We have a Cisco ASA 5520 with the VPN Plus License and 8.04 IOS installed, we want to set up vpn access to our users. We can use the Cisco VPN client which works on Windows Platform, but we also have MAC OS 10.7 which works only with Cisco Any connect.
I am a little bit lost with all the client and the license, actually we can't setup more than 2 vpn session with an Any connect client installed on MAC or Windows. The authentication is by Certificate, the first two connect fine, but the third one don't connect and prompt for a username / password. I joined a SH VER of my ASA, what is wrong on the license or perhaps it's a configuration problem?
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
[Code]....
We have bought L-ASA-AC-PH-5520=Anyconnect Vpn Phone License for our Cisco Phones but when we entered this license into our ASA it shows th following i.e enabled for linksys phones. Is there a diff part no to enable vpn for cisco phones. [code]
View 2 Replies View Relatedi have cisco 880 with NPE licence, but i need encryption on this device. I change IOS to c880data-universalk9-mz.151-3.T1.bin, but i still have NPE License and only Evalution without NPE. How can i have permanent license?
show license all
License Store: Primary License Storage
StoreIndex: 0 Feature: advsecurity_npe Version: 1.0
License Type: Permanent
License State: Active, Not in Use
[code]....
We’ve ordered ASA 5510 with security plus license as below description:
ASA5510-K8
ASA 5510 Appliance with SW, 5FE, DES
L-ASA5510-SEC-PL=
ASA 5510 Security Plus License w/ HA, GE, more VLANs + conns
The license details on the appliance shows as the below,
Fail over : Enabled
Encryption-DES : Enabled
Encryption-3DES-AES : Disabled
Security Contexts : Default
GTP/GPRS : Disabled
Any Connect Premium Peers : Default
Other VPN Peers : Default
Advanced Endpoint Assessment : Disabled
Any Connect for Mobile : Disabled
Any Connect for Cisco VPN Phone : Disabled
Shared License : Disabled
UC Phone Proxy Sessions : Default
Total UC Proxy Sessions : Default
Any Connect Essentials : Disabled
Bot net Traffic Filter : Disabled
Inter company Media Engine : Disabled
I’ve noticed that the 3DES is disabled, do I need to order another license to use 3DES or not ?Also, I need 2 ~ 5 branches to connect simultaneously and have VPN access on their laptops to the main branch via vpn software, which VPN software I should use and is our license enough or I should order another license.
I have 50 SSL Premium licenses on my ASA 5520 running 8.4. I want to run Anyconnect on IPAD- and IPHONE-devices but it seems that this requires a Mobile-license on top of the premium-license. Is it possible to receive an evaluation-license for this? It will take a few days to receive permanent licenses and I want to user this now.
View 1 Replies View RelatedI need to activate AnyConnect SecureMobility client on an IPAD. I have an ASA with the below feature licenses:
[code]...
This platform has an ASA 5520 VPN Plus license
As I've understood that I need the ASA-AC-M-5520 license for each IPAD used but they mentioned that we need also the Essential or premium license to be activated on the ASA as well. As shown above, I have the "VPN Plus license" activated on the firewall.
i had installed the SSL_VPN to the router C2911, running on IOS 15.0 But i couldn't see the SSL_VPN enable while i do show license feature? i did reload the router several time and accept the end user agreement.
attach the
01. show license feature
02. show license detail
I have a Cisco 1921 ISR Router with Security License running software version 15.0. I want to upgrade the router to 15.1. But I don't want to lose the security license that came with the router. When I look at the IOS downloads page on Cisco, all I see is universal images for all versions of 15.1.
My question is - where is the security license stored? In the IOS or programmed in somewhere else of the router? If I upgrade my router to one of the newer 15.1 universal images, will I lose my security license?
We are designing a solution for our customer, they plan to connect 5 site to their main office, on the main office, they use CISCO2911, branch use CISCO1921, so my question is:
1, If I want to use IPSec VPN connect branch and main office, apart from the router, I only need to buy the Security pack, like SL-19-SEC-K9/SL-29-SEC-K9, no need to buy SL-19-DATA-K9/SL-29-DATA-K9, am I right?
2, If I want to use SSL VPN connect branch and main office, apart from the router and SL-19-SEC-K9/SL-29-SEC-K9, I only need to buy L-FL-SSLVPN10-K9 for CISCO2911 in main office, no need to buy L-FL-SSLVPN10-K9 for branch as each CISCO1921 has two default SSL license?
I would like to Upgrade license Cisco 1941-K9 from ipbase to security
View 5 Replies View RelatedI have a cisco router 1941 and i have uploaded before evaluation license , now i have already bought cisco security license .I have already installed on cisco router , but the problem the router is still using the evaluation license not the new license .
RSP#sh flash:
-#- --length-- -----date/time------ path
1 55088360 Oct 10 2012 06:04:10 +00:00 c1900-universalk9-mz.SPA.151-4.M4.bin
2 2903 Feb 4 2013 12:23:32 +00:00 cpconfig-19xx.cfg
[Code].....